Alcatel-Lucent OmniSwitch 6850-48 Cli Reference Manual page 3696

show router ldp bindings ingress-label start-label [end-label]
show router ldp bindings egress-label start-label [end-label]
show router ldp bindings prefix ip-prefix/mask [session ip-address[:label-space]]]
show router ldp bindings active [prefix ip-prefix/mask]
show router ldp bindings vc-type vc-type [vc-id vc-id [session ip-address [:label-space]]
show router ldp bindings service-id service-id
show router ldp discovery [state {trying | established | down}] [detail]
show router ldp discovery peer ip-address [state {trying | established | down}] [detail]
show router ldp discovery interface ip-intf-name [state {trying | established | down}] [detail]
show router ldp interface [ip-intf-name | ip-address] [detail]
show router parameters
show router ldp peer [ip-address] [detail]
show router ldp session [ip-address
show router ldp status
MPLS Static LSP and FRR Commands
configure router mpls {no shutdown | shutdown}
configure router mpls interface ip-intf-name
configure router mpls no interface ip-intf-name
configure router mpls interface ip-intf-name {no shutdown | shutdown}
configure router mpls interface ip-intf-name label-map in-label
configure router mpls interface ip-intf-name no label-map in-label
configure router mpls interface ip-intf-name label-map in-label swap out-label next-hop ip-
address
configure router mpls interface ip-intf-name label-map in-label no swap
configure router mpls interface ip-intf-name label-map in-label pop
configure router mpls interface ip-intf-name label-map in-label no pop
configure router mpls interface ip-intf-name label-map in-label {no shutdown | shutdown}
configure router mpls static-lsp lsp-name
configure router mpls no static-lsp lsp-name
configure router mpls static-lsp lsp-name {no shutdown | shutdown}
configure router mpls static-lsp lsp-name to ip-address
configure router mpls static-lsp lsp-name push out-label next-hop ip-address
configure router mpls static-lsp lsp-name no push out-label
configure router mpls interface ip-intf-name label-map in-label protect-swap out-label next-
hop ip-address
configure router mpls interface ip-intf-name label-map in-label no protect-swap
show router mpls interface [ip-intf-name] [label-map label [protect-swap [out-label]]]
show router mpls label start-label [end-label [label-filter]]
show router mpls label-range
show router mpls static-lsp [lsp-name | transit | terminate | count]
show router mpls status
OmniSwitch CLI Reference Guide
[ ]
:label-space ] [detail | statistics [packet-type]]
June 2012
Virtual Private LAN Service (VPLS) Commands
configure service customer customer-id create
configure service no customer customer-id
configure service customer customer-id contact contact-info
configure service customer customer-id no contact
configure service customer customer-id phone phone-info
configure service customer customer-id no phone
configure service customer customer-id description desc-info
configure service customer customer-id no description
configure service sdp sdp-id [mpls] create
configure service no sdp sdp-id
configure service sdp sdp-id description desc-info
configure service sdp sdp-id no description
configure service sdp sdp-id far-end ip-address
configure service sdp sdp-id no far-end
configure service sdp sdp-id {no shutdown | shutdown}
configure service sdp sdp-ip
configure service sdp sdp-ip
configure service sdp sdp-ip signaling
configure service sdp sdp-ip
configure service sdp sdp-ip
configure service sdp sdp-ip
configure service sdp sdp-ip
configure service sdp sdp-ip
configure service sdp sdp-ip
configure service vpls service-id
configure service no vpls service-id
configure service vpls service-id
configure service vpls service-id
configure service vpls service-id
configure service vpls service-id
configure service no vpls service-id
configure service vpls service-id
configure service no vpls service-id
configure service vpls service-ip
configure service vpls service-ip
configure service vpls service-id
configure service vpls service-id
configure service vpls service-id
configure service vpls service-id
configure service vpls service-id
configure service vpls service-id
configure service vpls service-id
page 28
ldp
no ldp
{off | tldp}
lsp
lsp-name
no lsp
lsp-name
adv-mtu-override
no adv-mtu-override
path-mtu
bytes
no path-mtu
customer
customer-id create
[customer
customer-id] description desc-info
[customer
customer-id] no description
[customer
customer-id] {no shutdown | shutdown}
[customer
customer-id] def-mesh-vc-id vc-id
[customer
customer-id] no def-mesh-vc-id
[customer
customer-id] send-flush-on-failure
[customer
customer-id] no send-flush-on-failure
[customer service-mtu
customer-id]
[customer no service-mtu
customer-id]
mesh-sdp
sdp-id[:vc-id] [vc-type {ether | vlan} create
no mesh-sdp
sdp-id
mesh-sdp
sdp-id[:vc-id] {no shutdown | shutdown}
mesh-sdp
sdp-id[:vc-id] egress vc-label egress-vc-label
no mesh-sdp
sdp-id no egress vc-label
mesh-sdp
sdp-id[:vc-id] ingress vc-label ingress-vc-label
no mesh-sdp
sdp-id no ingress vc-label
MPLS Static LSP and FRR Commands
bytes