078-104 Hcf Feed Out Sensor Fault Rap; 078-210 Hcf To Tray 1 Lift Rap - Xerox WorkCentre 5222 Service Manual

078-104 HCF Feed Out Sensor Fault RAP

BSD-ON: 8.9
The paper transported from HCF did not turn on the Feed Out Sensor within the specified time.
Initial Actions
• Clear any jam and switch the power off then on.
• Check for out-of-spec paper.
• Paper Path for a foreign object/burr/piece of paper
Procedure
Execute Component Control [078-101 Tray 6 Feed out Sensor]. Place paper in front of the
Feed Out Sensor. The display changes.
Y N
Go to 8.9 BSD and check the following for an open wire, short or poor contact:
• Feed Out Sensor PF67-2 to HCF PWB PF01-2
• Feed Out Sensor PF67-1 to HCF PWB JF01-3
• Feed Out Sensor PF67-3 to HCF PWB JF01-1
If OK, replace the Feed Out Sensor
Execute Component Control [078-007 Tray 6 Takeaway Motor]. There is operation noise
from the Tray 6 Takeaway Motor.
Y N
Check the wire-wound resistance of Tray 6 Takeaway Motor is approx. 0.8 ohms at the mea-
surement points below.
• JF57-3 to pins 1/2
• JF57-4 to pins 5/6
If OK, go to 8.9 BSD and troubleshoot the Tray 6 Takeaway Motor circuit.
Check the HCF paper lift components and repair as required
Status Indicator Raps
078-104 , 078-210
(PL 18.7) before replacing the HCF PWB
(PL 18.2, PL 18.3).

078-210 HCF to Tray 1 Lift RAP

BSD-ON:7.7
The Tray 1 Level Sensor did not actuate in time after the Tray 1 Feed/Lift Motor energized.
Initial Actions
Ensure the tray is set up and loaded correctly.
Procedure
Execute Component Control
Lift Motor (PL 2.3) can be heard (the lifted paper plate drops when the tray is opened).
Y N
Check the connections of P/J201,
J409 are connected correctly.
Y N
Connect P/J201,
Remove the Tray 1 Feed/Lift Motor
Replace the Tray 2 Feed/Lift Motor with the Tray 1 Feed/Lift Motor.
(PL 18.8). Execute Component Control
Lift Motor can be heard (the lifted paper plate drops when the tray is opened).
Y N
Return the Tray 1 Feed/Lift Motor to its original position.
Check the wires between
(BSD 7.7 Flag
out an open circuit or a short circuit.
Y N
Repair the open circuit or short circuit.
Replace the Tray Module PWB
Return the Tray 1 Feed/Lift Motor to its original position.
Replace the Tray 2 Feed/Lift Motor
Check the installation of the Tray 1 Level Sensor
The Tray 1 Level Sensor is installed correctly and the actuator works.
Y N
Reinstall the Tray 1 Level Sensor
Execute Component Control
Sensor (PL 2.3). The display changes.
Y N
Check the connections of P/J100,
are connected correctly.
Y N
Connect P/J100,
Check the wires between
7.7 Flag 2/Flag 3). The wires between
open circuit or a short circuit.
A
February, 2008
2-558
[071-001 or 007 Tray 1 Feed/Lift Motor ON]. The Tray 1 Feed/
P/J601 and P/J409. P/J201,
P/J601 and P/J409.
(PL 2.3) and the Tray 2 Feed/Lift Motor
[072-001/002 Tray 2 Feed/Lift Motor ON]. The Tray 2 Feed/
P/J201 and P/J409 for an open circuit or a short circuit
1). The circuit between P/J201 and
(PL 13.8).
(PL 2.3).
(PL 2.3) and the operation of the actuator.
(PL 2.3).
[071-201 Tray 1 Level Sensor]. Manually activate the Tray 1 Level
P/J601 and P/J409. P/J100,
P/J601 and P/J409.
P/J100 and P/J409 for an open circuit or a short circuit (BSD
P/J100 and P/J409
P/J601 and P/J549 P/
(PL 2.3).
P/J409 is conducting with-
P/J601 and P/J409
are conducting without an
Launch Version
WorkCentre 5225, 5230