078-945 Ttm Tray 3 Lift Rap - Xerox WorkCentre 5222 Service Manual

078-945 TTM Tray 3 Lift RAP

BSD-ON:7.9/7.11/7.12
There is a problem with the TTM Tray 3 Lift.
Procedure
Enter Component Control [071-002 or 073-009 Tray 3 Feed/Lift Motor ON]. The Tray 3 Feed/
Lift Motor (PL 12.3) can be heard (the lifted paper plate drops when the tray is opened).
Y N
Check the connections of P/J220B, P/J661B, P/J549. P/J220B, P/J661B,
connected correctly.
Y N
Connect P/J220B, P/J661B, P/J549.
Remove the Tray 3 Feed/Lift Motor (PL
Replace the Tray 3 Feed/Lift Motor with the Tray 2 Feed/Lift Motor.
Enter Component Control [071-002 or 073-009 Tray 3 Feed/Lift Motor ON]. The Tray 3
(2) Feed/Lift Motor (PL 12.3) can be heard (the lifted paper plate drops when the tray
is opened).
Y N
Return the Tray 2 Feed/Lift Motor to its original position.
Check the wires between P/J220B
(BSD 7.12 Flag 1). The circuit between J220B and J549 is conducting without
an open circuit or a short circuit.
Y N
Repair the open circuit or short circuit.
Replace the Tray Module PWB
Return the Tray 2 Feed/Lift Motor to its original position.
Replace the Tray 3 Feed/Lift Motor (PL
Check the installation of the Tray 3 Level Sensor
The Tray 3 Level Sensor is installed correctly and the actuator works.
Y N
Reinstall the Tray 3 Level Sensor (PL
Enter Component Control [071-208 Tray 3 Level Sensor]. Manually actuate the Tray 3 Level
Sensor (PL 12.3). The display changes.
Y N
Check the connections of P/J101B,
J549 are connected correctly.
Y N
Connect P/J101B, P/J661B and P/J549.
Check the wires between P/J101B and
7.12 Flag 2/Flag 3). The circuit between J101B and J549 is conducting without an
open circuit or a short circuit.
Y N
Repair the open circuit or short circuit.
A B
Launch Version
WorkCentre 5225, 5230
P/J549
12.3) and the Tray 2 Feed/Lift Motor (PL
and P/J549 for an open circuit or a short circuit
(PL 13.8).
12.3).
(PL 12.3) and the operation of the actuator.
12.3).
P/J661B and P/J549. P/J101B, P/J661B
P/J549 for an open circuit or a short circuit (BSD
A B
Measure the voltage between the Tray Module PWB P/J549-7 (+) and P/J549-8 (-) (BSD
7.12 Flag 3). The voltage is approx. +5VDC.
Y N
Replace the Tray Module PWB
Measure the voltage between the Tray Module PWB P/J549-9 (+) and GND (-) (BSD
7.12 Flag 2).
Activate the actuator of the Tray 3 Level Sensor
Y N
Replace the Tray 3 Level Sensor
are
Replace the Tray Module PWB
Check the TTM paper lift components and repair as required
12.3).
and P/
February, 2008
2-563
(PL 13.8).
(PL 12.3). The voltage changes.
(PL 12.3).
(PL 13.8).
(PL 12.3, PL 13.8).
Status Indicator Raps
078-945