Of 3 Main Drive Assy Rap; Of 4 Dark / Blank Display Rap - Xerox WorkCentre 5222 Service Manual

Tabloid black-and-white multifunction printer
Hide thumbs Also See for WorkCentre 5222:
Table of Contents

Advertisement

OF 3 Main Drive Assy RAP

Procedure
Execute
Component Control
[071-037 Drum Motor ON]. The Drum Motor can be heard.
Y
N
Check the connections of
P/J408
and P/J214.
rectly.
Y
N
Connect
P/J408
and P/J214.
Check the wire between
P/J408
and P/J2144 for an open circuit or a short circuit (BSD
4.1
Flag 3/Flag 4/Flag 5/Flag 6/Flag
ducting without an open circuit or a short circuit.
Y
N
Repair the open circuit or short circuit.
Measure the voltage between the MCU PWB P408-13 (+) and GND (-), and between
P408-14 (+) and GND (-) (BSD 4.1
Y
N
Replace the MCU PWB
(PL
9.1).
Measure the voltage between the MCU PWB P408-10 (+) and GND (-) (BSD 4.1
The voltage is approx. +5VDC.
Y
N
Replace the MCU PWB
(PL
9.1).
Replace the Main Drive Assembly
PWB
(PL
9.1).
Check the wires between the following points for an open circuit or a short circuit. The wire
between the points is conducting without an open circuit or a short circuit.
Between J408-3 and J214-12 (BSD 4.1
Between J408-8 and J214-7 (BSD 4.1
Between J408-9 and J214-6 (BSD 4.1
Y
N
Repair the open circuit or short circuit.
Replace the Main Drive Assembly
(PL
1.1). If the problem persists, replace the MCU PWB
9.1).
Launch Version
WorkCentre 5225, 5230
P/J408
and
P/J214
are connected cor-
7). The wire between
P/J408
and
P/J214
Flag
4). The voltage is approx. +24VDC.
(PL
1.1). If the problem persists, replace the MCU
Flag
2)
Flag
2)
Flag
1)

OF 4 Dark / Blank Display RAP

Touch Screen is dark with minimal legibility, or no text or graphics are visible, or text or graph-
ics are distorted, or indicator LED's are not lit.
Initial Actions
Ensure all external cables and power cords are connected.
Procedure
NOTE: If a Status Code is displayed, go to the appropriate status code RAP.
is con-
There is some luminance in the UI display.
Y
N
Switch off the power. Listen to the cooling fans on the right side and at the rear of the
machine and switch on the power. Cooling fans are audible either momentarily or
continuously.
Y
N
There is a +5VDC failure. Go to BSD 1.1 and check 5VDC standby voltages.
+24VDC is measured between
Y
N
Flag
3).
+24VDC is measured between
2.3).
Y
N
+24VDC is measured between
1.1).
Y
N
+24VDC is measured between
Unit (BSD 1.1).
Y
N
AC voltage is measured between
the Power unit (BSD 1.1).
Y
(PL
AC voltage is measured at
Y
Replace Power Unit
Go to BSD 1.1 and check circuit between P/J521 on Power Unit and P/
J387 on ESS PWB.
A
B
C
D
February, 2008
2-719
P/J1
pin 40 and ground on Control Panel (BSD 2.3).
P/J388
pin 40 and pins 25, 26 on the ESS (BSD
P/J300
pin 2 and ground on the ESS (BSD
P/J521
pin 3 and ground on Power
P/J11
pin 1 and J12 pin 1 on
N
AC voltage is measured at wall outlet.
Y
N
Contact key operator to resolve power problem.
GFI Breaker is tripped.
Y
N
Replace GFI Breaker
(PL
9.1).
Reset GFI Breaker.
P/J1
pin 3 and ground (BSD 1.1).
N
Replace Main Power Switch
(PL
9.1).
(PL
9.1).
Status Indicator Raps
OF 3, OF 4

Advertisement

Table of Contents
loading

This manual is also suitable for:

Workcentre 5225Workcentre 5230

Table of Contents