077-305 Tray Module Left Hand Cover Interlock Open Rap; 077-307 Dup Cover Open Rap - Xerox WorkCentre 5222 Service Manual

077-305 Tray Module Left Hand Cover Interlock Open RAP

BSD-ON:1.4
• The 2TM Cover is open.
• The TTM Cover is open.
Initial Actions
• Power OFF/ON
• Opening/closing of the Left Cover of the 2TM or TTM.
Procedure
Check opening/closing of the Left Cover of the 2TM or TTM. The Left Cover of the 2TM or
TTM can be opened/closed.
Y N
Reinstall the Left Cover of the 2TM or TTM
Check the installation of the Tray Module Interlock Switch. The Tray Module interlock Switch
is installed correctly.
Y N
Install the Tray Module interlock Switch
Execute Component Control [071-301 Tray Module Left Cover Interlock Switch]. Open and
close the Left Cover of the 2TM or TTM. The display changes.
Y N
Check the connections of P/J554,
connected correctly.
Y N
Connect P/J554, FS812 and FS813.
Check the wire between J554-2 and FS812, and between J554-1 and FS813 for an open
circuit or a short circuit (BSD 1.4 Flag 3/Flag
and between J554-1 and FS813 are conducting without an open circuit or a short
circuit.
Y N
Repair the open circuit or short circuit.
Check the conductivity of the Tray Module Left Cover Interlock Switch
between FS813 and FS812 (BSD 1.4
FS812 is connecting successfully when the 2TM Cover or TTM Cover is closed, and
is insulated when the cover is open.
Y N
Replace the Tray Module Left Cover Interlock Switch
Replace the Tray Module PWB (PL 12.6/PL
Replace the Tray Module PWB (PL 12.6/PL
Status Indicator Raps
077-305, 077-307
(PL 12.4/PL 13.7).
(PL 12.4/PL 13.7) correctly.
FS812 and FS813. P/J554, FS812 and
4). The wires between J554-2 and FS812,
(PL 12.4/PL
Flag 3/Flag 4). The wire between FS813 and
(PL 12.4/PL 13.7).
13.8).
13.8).

077-307 DUP Cover Open RAP

BSD-ON:1.4
The DUP Cover is open.
Initial Actions
• Power OFF/ON
• Opening/closing of the DUP Cover.
Procedure
Check opening/closing of the DUP Cover. The DUP Cover can be opened/closed.
Y N
Reinstall the DUP Cover.
Check the installation of the Duplex Open Switch
installed correctly.
Y N
Install the Duplex Open Switch
Execute Component Control
Cover. The display changes.
Y N
Check the connections of
rectly.
FS813 are
Y N
Connect P/J124
Check the wire between J124 and J541 for an open circuit or a short circuit (BSD 1.4
5/Flag 6). The wire between J124 and J541 is conducting without an open circuit or
a short circuit.
Y N
Repair the open circuit or short circuit.
Check the conductivity of the Duplex Open Switch
(BSD 1.4 Flag 5/Flag
fully when the DUP Cover is closed, and is insulated when the cover is open.
13.7)
Y N
Replace the Duplex Open Switch
Replace the MCU PWB
Replace the MCU PWB
February, 2008
2-554
(PL 8.1). The Duplex Open Switch is
(PL 8.1) correctly.
[071-305 Duplex Open Switch]. Open
P/J124 and P/J541. P/J124 and
and P/J541.
(PL 8.1) between J541-4 and J541-5
6). The wire between J541-4 and J541-5 is connecting success-
(PL 8.1).
(PL 9.1).
(PL 9.1).
and close the DUP
P/J541 are connected cor-
Flag
Launch Version
WorkCentre 5225, 5230