074-101 Tray 4 Miss Feed Jam Rap - Xerox WorkCentre 5222 Service Manual

074-101 Tray 4 Miss Feed JAM RAP

BSD-ON:3.3/7.10/8.5
After the Tray 4 Feed/Lift Motor turned On, the Tray 4 Feed Out Sensor did not turn On within
the specified time.
Initial Actions
• Power OFF/ON
Procedure
Check the Transport Roll for wear and paper powder. The Transport Roll is ok.
Y N
Replace the Transport Roll.
Check for foreign substances, distortion and paper powder in the paper transport path. No
distortion, foreign substances, or paper powder are found in the paper transport path.
Y N
Clear away the foreign substances and paper powder. Correct the distortion.
Execute Component Control [071-102 Tray 4 Feed Out Sensor]. Actuate the Tray 4 Feed Out
Sensor (PL 12.5/PL 13.4) with paper. The display changes.
Y N
Check the connections of P/J825, P/J842, P/J548,
tors are connected correctly.
Y N
Connect the connectors.
Check the wire between J825 and J548 for an open circuit or a short circuit (BSD 8.5).
The wire between J825 and J548 is conducting without an open circuit or a short
circuit.
Y N
Repair the open circuit or short circuit.
Measure the voltage between the Tray Module PWB P548-1 (+) and GND (-) (BSD 8.5).
The voltage is approx. +5VDC.
Y N
Replace the Tray Module PWB
Measure the voltage between the Tray Module PWB P548-3 (+) and GND (-) (BSD 8.5).
Actuate the Tray 4 Feed Out Sensor
changes.
Y N
Replace the Tray 4 Feed Out Sensor
Check the wire between J541-11 and J413-B5 for an open circuit or a short circuit (BSD
3.3 Flag 2). The wire between J541-11 and J413-B5 is conducting without an open
circuit or a short circuit.
Y N
Repair the open circuit or short circuit.
Measure the voltage between the MCU PWB P413-B5 (+) and GND (-) (BSD 3.3
A
Launch Version
WorkCentre 5225, 5230
P/J541 and P/J413. The connec-
(PL 12.6/PL 13.8).
(PL 12.5/PL 13.4) with paper. The
(PL 12.5/PL 13.4).
A
Actuate the Tray 3 Feed Out Sensor
changes.
Y N
Replace the Tray Module PWB
Replace the MCU PWB
Execute Component Control
Motor (PL 12.3/PL 13.6) can be heard.
Y N
Check the connections of P/J220A, P/J661A, P/J549,
P/J661A, P/J549, P/J541
Y N
Connect P/J220A, P/J661A, P/J549,
Remove the Tray 4 Feed/Lift Motor
12.3/PL 13.6).
Replace the Tray 4 Feed/Lift Motor with the Tray 3 Feed/Lift Motor.
Execute Component Control
Motor (PL 12.3/PL 13.6) can be heard.
Y N
Return the Tray 3 Feed/Lift Motor to its original position.
Check the wire between J220A and J549 for an open circuit or a short circuit (BSD
7.10 Flag 1 / BSD 7.12
without an open circuit or a short circuit.
Y N
Repair the open circuit or short circuit.
Replace the Tray Module PWB
Return the Tray 3 Feed/Lift Motor to its original position.
Replace the Tray 4 Feed/Lift Motor
Replace the Tray Module PWB
voltage
Flag 2).
February, 2008
2-535
(PL 12.5/PL 13.5) with paper. The
(PL 12.6/PL 13.8).
(PL 9.1).
[073-010 Tray 4 Feed/Lift Motor ON]. The
P/J541 and P/J413.
and P/J413 are connected correctly.
P/J541 and P/J413.
(PL 12.3/PL 13.6) and the Tray 3 Feed/Lift Motor
[073-010 Tray 4 Feed/Lift Motor ON]. The Tray 3 Feed/Lift
Flag 1). The wire between J220A and J549 is conducting
(PL 12.6/PL 13.8).
(PL 12.3/PL 13.6).
(PL 12.6/PL 13.8).
voltage
Tray 4 Feed/Lift
P/J220A,
(PL
Status Indicator Raps
074-101