024-953 Tray 4 Empty Rap; 024-954 Mpt Empty Rap - Xerox WorkCentre 5222 Service Manual

024-953 Tray 4 Empty RAP

Tray 4 has run out of paper.
Initial Actions
• Refer to BSD 7.10/7.12.
Procedure
Check the installation of the Tray 4 No Paper Sensor
the actuator. The Tray 4 Level Sensor is installed correctly and the actuator works.
Y N
Reinstall the Tray 4 Level Sensor.
Execute Component Control[071-204 Tray 4 No Paper Sensor]. Manually activate the Tray 4
No Paper Sensor (PL 12.3/PL 13.6). The display changes.
Y N
Check the connections of P/J102A,
J549 are connected correctly.
Y N
Connect P/J102A, P/J661A and P/J549.
Check the wire between J102A and J549 for an open circuit or a short circuit (BSD 7.10
Flag 4/Flag 5 / BSD 7.12 Flag 4/Flag
ducting without an open circuit or a short circuit.
Y N
Repair the open circuit or short circuit.
Measure the voltage between the Tray Module PWB P549-A10 (+) and GND (-) (BSD
7.10 Flag 5 / BSD 7.12 Flag 5). The voltage is approx. +5VDC.
Y N
Replace the Tray Module PWB
Measure the voltage between the Tray Module PWB P549-A12 (+) and GND (-) (BSD
7.10 Flag 4 / BSD 7.12 Flag 4).
Activate the actuator of the Tray 4 No Paper Sensor
changes.
Y N
Replace the Tray 4 No Paper Sensor
Replace the Tray Module PWB (PL 12.6/PL
Replace the Tray Module PWB (PL 12.6/PL
Status Indicator Raps
024-953, 024-954
(PL 12.3/PL 13.6) and the operation of
P/J661A and P/J549. P/J102A, P/J661A
5). The wire between J102A and J549 is con-
(PL 12.6/PL 13.8).
(PL 12.3/PL 13.6). The
(PL 12.3/PL 13.6).
13.8).
13.8).

024-954 MPT Empty RAP

The MPT has run out of paper.
Initial Actions
• Refer to BSD 7.13.
Procedure
Check the installation of the MPT No Paper Sensor
The MPT No Paper Sensor is installed correctly and the actuator works.
Y N
Reinstall the MPT No Paper Sensor.
Execute Component Control[071-205 MPT No Paper Sensor]. Manually activate the MPT No
Paper Sensor (PL 7.1). The display changes.
Y N
and P/ Check the connections of P/J108,
are connected correctly.
Y N
Connect P/J108,
Check the wire between J108 and J411 for an open circuit or a short circuit (BSD 7.13
Flag 3/Flag 4). The wire between J108 and J411 is conducting without an open cir-
cuit or a short circuit.
Y N
Repair the open circuit or short circuit.
Measure the voltage between the MCU PWB P411-6 (+) and GND (-) (BSD 7.13
The voltage is approximately. +5VDC.
Y N
Replace the MCU PWB
Measure the voltage between the MCU PWB P411-8 (+) and GND (-) (BSD 7.13
Activate the actuator of the MPT No Paper Sensor
voltage Y N
Replace the MPT No Paper Sensor
Replace the MCU PWB
Replace the MCU PWB (PL
February, 2008
2-354
(PL 7.1) and the operation of the actuator.
P/J605 and P/J411. P/J108,
P/J605 and P/J411.
(PL 9.1).
(PL 7.1). The voltage changes.
(PL 7.1).
(PL 9.1).
9.1).
P/J605 and P/J411
Flag 4).
Flag 3).
Launch Version
WorkCentre 5225, 5230