Nvm List Of Lead Edge; Nvm List Of Side Edge - Xerox WorkCentre 5222 Service Manual

Adjustment
1. Access Diagnostic Routines.
a. Enter UI Diagnostics (UI Diagnostic
2. Select NVM Read/Write.
3. Adjust the measured values of the Lead (A) and Side Edges (B) using the following NVM
so that the measured values fall within the specifications of the respective supporting
modes.
If the measured value is shorter than specification above (A or B): Set a larger value.
If the measured value is longer than specification above (A or B): Set a smaller value.
• Adjustment of A (Lead Edge), refer to
• Adjustment of B (Side Edge), refer to
Table 3 NVM List of Lead Edge
Chain Link Name
742-027 LEAD REGI ADJUSTMENT - ALL TRAY
760-001 TRAY1 for Normal Paper - LEAD REGI
ADJUSTMENT
760-002 TRAY2-4 for Normal Paper - LEAD REGI
ADJUSTMENT
760-003 MPT for Normal Paper - LEAD REGI
ADJUSTMENT
760-005 DUP ALL SIZE for Normal Paper - LEAD
REGI ADJUSTMENT
760-013 DUP A3 Group - LEAD REGI ADJUST-
MENT
760-014 DUP A4S Group - LEAD REGI ADJUST-
MENT
760-015 DUP A4L Group - LEAD REGI ADJUST-
MENT
760-016 TRAY1 for Thick-1 Paper - LEAD REGI
ADJUSTMENT
760-017 TRAY1 for Thick-2 Paper - LEAD REGI
ADJUSTMENT
760-018 TRAY2-4 for Thick-1 Paper - LEAD REGI
ADJUSTMENT
760-019 TRAY2-4 for Thick-2 Paper - LEAD REGI
ADJUSTMENT
760-020 MPT for Thick-1 Paper - LEAD REGI
ADJUSTMENT
760-021 MPT for Thick-2 Paper - LEAD REGI
ADJUSTMENT
760-022 DUP ALL SIZE for Thick-1 Paper - LEAD
REGI ADJUSTMENT
760-023 DUP ALL SIZE for Thick-2 Paper - LEAD
REGI ADJUSTMENT
Repairs and Adjustments
ADJ 9.1.1
Mode).
Table 3 below.
Table 4 below.
Initia
Min. l Max Increment
0 33 66 0.2175mm
0 33 66 0.363mm
0 33 66 0.363mm
0 33 66 0.363mm
0 33 66 0.363mm
0 10 16 0.363mm
0 10 16 0.363mm
0 10 16 0.363mm
0 33 66 0.363mm
0 33 66 0.363mm
0 33 66 0.363mm
0 33 66 0.363mm
0 33 66 0.363mm
0 33 66 0.363mm
0 33 66 0.363mm
0 33 66 0.363mm
Chain Link Name
760-24 Tray 2-=4, HCF for Thick-1 Paper-REGI
LOOP TIMER
760-25 Tray3-4, HCF for Thick-2 Paper-REGI
LOOP TIMER
760-031 TRAY1 for Thick-4 Paper - LEAD REGI
ADJUSTMENT
760-032 TRAY2-4 for Thick-4 Paper - LEAD REGI
ADJUSTMENT
760-033 MPT for Thick-4 Paper - LEAD REGI
ADJUSTMENT
760-034 DUP ALL SIZE for Thick-4 Paper - LEAD
REGI ADJUSTMENT
Chain Link Name
749-001 ALL TRAY-LASER SIDE REGI ADJUST-
MENT
749-002 TRAY1-LASER SIDE REGI ADJUSTMENT
749-003 TRAY2-LASER SIDE REGI ADJUSTMENT
749-004 TRAY3-LASER SIDE REGI ADJUSTMENT
749-005 TRAY4-LASER SIDE REGI ADJUSTMENT
749-007 MPT-LASER SIDE REGI ADJUSTMENT
749-009 DUP ALL TRAY-LASER SIDE REGI
ADJUSTMENT
749-010 DUP TRAY1-LASER SIDE REGI ADJUST-
MENT
749-011 DUP TRAY2-LASER SIDE REGI ADJUST-
MENT
749-012 DUP TRAY3-LASER SIDE REGI ADJUST-
MENT
749-013 DUP TRAY4-LASER SIDE REGI ADJUST-
MENT
749-015 DUP MPT-LASER SIDE REGI ADJUST-
MENT
4. After adjustment, print the test pattern in the same mode and measure the Lead and Side
Edge values. Repeat this procedure until the values fall within the specifications.
5. Repeat the procedure until the measured values of the Lead (A) and Side Edges (B) fall
within the specifications.
February, 2008
4-224
Table 3 NVM List of Lead Edge
Initia
Min. l
0 33
0 33
0 33
0 33
0 33
0 33
Table 4 NVM List of Side Edge
Initia
Min. l
1 50
1 50
1 50
1 50
1 50
1 50
1 50
1 50
1 50
1 50
1 50
1 50
WorkCentre 5225, 5230
Max Increment
66 0.363mm
66 0.363mm
66 0.363mm
66 0.363mm
66 0.363mm
66 0.363mm
Max Increment
99 0.254mm
99 0.254mm
99 0.254mm
99 0.254mm
99 0.254mm
99 0.254mm
99 0.254mm
99 0.254mm
99 0.254mm
99 0.254mm
99 0.254mm
99 0.254mm
Launch Version