Huawei Quidway NetEngine80E Configuration Manual page 508
Universal service router, ip routing
Hide thumbs
Also See for Quidway NetEngine80E:
- Configuration manual - reliability (1432 pages) ,
- Configuration manual (341 pages) ,
- Installation manual (169 pages)
Advertisement
HUAWEI NetEngine80E/40E Router
Configuration Guide - IP Routing
Procedure
Step 1 Assign an IPv6 address to each router interface.
The detailed configuration is not mentioned here.
Step 2 Configure the basic OSPFv3 functions.
# Configure Router A.
[RouterA] ipv6
[RouterA] ospfv3
[RouterA-ospfv3-1] router-id 1.1.1.1
[RouterA-ospfv3-1] quit
[RouterA] interface gigabitethernet 1/0/0
[RouterA-GigabitEthernet1/0/0] ipv6 enable
[RouterA-GigabitEthernet1/0/0] ospfv3 1 area 0
[RouterA-GigabitEthernet1/0/0] quit
[RouterA] interface gigabitethernet 1/0/1
[RouterA-GigabitEthernet1/0/1] ipv6 enable
[RouterA-GigabitEthernet1/0/1] ospfv3 1 area 0.0.0.0
[RouterA-GigabitEthernet1/0/1] quit
# Configure Router B.
[RouterB] ipv6 enable
[RouterB] ospfv3 1
[RouterB-ospfv3-1] router-id 2.2.2.2
[RouterB-ospfv3-1] quit
[RouterB] interface gigabitethernet 1/0/0
[RouterB-GigabitEthernet1/0/0] ipv6 enable
[RouterB-GigabitEthernet1/0/0] ospfv3 1 area 0.0.0.0
[RouterB-GigabitEthernet1/0/0] quit
[RouterB] interface gigabitethernet 1/0/1
[RouterB-GigabitEthernet1/0/1] ipv6 enable
[RouterB-GigabitEthernet1/0/1] ospfv3 1 area 0.0.0.0
[RouterB-GigabitEthernet1/0/1] quit
[RouterB] interface gigabitethernet 1/0/2
[RouterB-GigabitEthernet1/0/2] ipv6 enable
[RouterB-GigabitEthernet1/0/2] ospfv3 1 area 0.0.0.0
# Configure Router C.
[RouterC] ospfv3 1
[RouterC-ospfv3-1] router-id 3.3.3.3
[RouterC-ospfv3-1] quit
[RouterC] interface gigabitethernet 1/0/0
[RouterC-GigabitEthernet1/0/0] ipv6 enable
[RouterC-GigabitEthernet1/0/0] ospfv3 1 area 0.0.0.0
[RouterC-GigabitEthernet1/0/0] quit
[RouterC] interface gigabitethernet 1/0/1
[RouterC-GigabitEthernet1/0/1] ipv6 enable
[RouterC-GigabitEthernet1/0/1] ospfv3 1 area 0.0.0.0
# After the preceding configurations are complete, run the display ospfv3 peer command. You
can view that the neighboring relationship is set up between Router A and Router B, and that
between Router B and Router C. Take the display of Router A as an example:
[RouterA] display ospfv3 peer verbose
OSPFv3 Process (1)
Neighbor 2.2.2.2 is Full, interface address FE80::E0:CE19:8142:1
Issue 02 (2014-09-30)
In the area 0.0.0.0 via interface GE1/0/0
DR Priority is 1 DR is 2.2.2.2 BDR is 1.1.1.1
Options is 0x000013 (-|R|-|-|E|V6)
Dead timer due in 00:00:34
Neighbour is up for 01:30:52
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6 OSPFv3 Configuration
483
Hide quick links:
Advertisement
