Huawei Quidway NetEngine80E Configuration Manual page 728
Universal service router, ip routing
Hide thumbs
Also See for Quidway NetEngine80E:
- Configuration manual - reliability (1432 pages) ,
- Configuration manual (341 pages) ,
- Installation manual (169 pages)
Advertisement
HUAWEI NetEngine80E/40E Router
Configuration Guide - IP Routing
[PE1] display ip routing-table 1.1.1.1 32
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Table : Public
Summary Count : 1
Destination/Mask
GigabitEthernet1/0/0
Step 3 Configure an MPLS TE tunnel.
Enable MPLS, MPLS TE, and RSVP-TE on the interfaces of P1, P2, P3, and P4, and enable
CSPF on the ingress of the tunnel.
Configure P1 and P2. The configuration of P3 is similar to that of P1, and the configuration of
P4 is similar to that of P2.
# Configure P1.
[P1] mpls lsr-id 1.1.1.1
[P1] mpls
[P1-mpls] mpls te
[P1-mpls] mpls rsvp-te
[P1-mpls] mpls te cspf
[P1-mpls] quit
[P1] interface gigabitethernet 1/0/0
[P1-GigabitEthernet1/0/0] mpls
[P1-GigabitEthernet1/0/0] mpls te
[P1-GigabitEthernet1/0/0] mpls rsvp-te
[P1-GigabitEthernet1/0/0] mpls te bandwidth max-reservable-bandwidth 200000
[P1-GigabitEthernet1/0/0] mpls te bandwidth bc0 200000
[P1-GigabitEthernet1/0/0] quit
# Configure P2.
[P2] mpls lsr-id 2.2.2.2
[P2] mpls
[P2-mpls] mpls te
[P2-mpls] mpls rsvp-te
[P2-mpls] quit
[P2] interface gigabitethernet 1/0/0
[P2-GigabitEthernet1/0/0] mpls
[P2-GigabitEthernet1/0/0] mpls te
[P2-GigabitEthernet1/0/0] mpls rsvp-te
[P2-GigabitEthernet1/0/0] mpls te bandwidth max-reservable-bandwidth 200000
[P2-GigabitEthernet1/0/0] mpls te bandwidth bc0 200000
[P2-GigabitEthernet1/0/0] quit
[P2] interface gigabitethernet 2/0/0
[P2-GigabitEthernet2/0/0] mpls
[P2-GigabitEthernet2/0/0] mpls te
[P2-GigabitEthernet2/0/0] mpls rsvp-te
[P2-GigabitEthernet2/0/0] mpls te bandwidth max-reservable-bandwidth 200000
[P2-GigabitEthernet2/0/0] mpls te bandwidth bc0 200000
[P2-GigabitEthernet2/0/0] quit
# On P1, configure an explicit path for the TE tunnel. The configuration of P3 is similar to that
of P1 and is not mentioned here.
[P1] explicit-path to_P3
[P1-explicit-path-to_p3] next hop 10.1.1.2
[P1-explicit-path-to_p3] next hop 10.1.4.2
[P1-explicit-path-to_p3] next hop 10.1.6.1
[P1-explicit-path-to_p3] next hop 3.3.3.3
[P1-explicit-path-to_p3] quit
Issue 02 (2014-09-30)
Proto
1.1.1.1/32
ISIS-L2
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Pre
Cost
Flags NextHop
15
5
D
7 IS-IS Configuration
Interface
10.1.10.2
703
Hide quick links:
Advertisement
