Huawei Quidway NetEngine80E Configuration Manual page 727
Universal service router, ip routing
Hide thumbs
Also See for Quidway NetEngine80E:
- Configuration manual - reliability (1432 pages) ,
- Configuration manual (341 pages) ,
- Installation manual (169 pages)
Advertisement
HUAWEI NetEngine80E/40E Router
Configuration Guide - IP Routing
Procedure
Step 1 Configure IP addresses for interfaces.
Configure the IP address and mask for each interface according to
This example assumes that you know the configuration method and no details are provided here.
Step 2 Configure IS-IS.
Configure IS-IS on all the PE and P nodes, and configure P1 and PE1. The configurations of
other nodes are similar to the configurations of P1 and PE1 and therefore are not mentioned here.
# Configure P1.
[P1] router id 1.1.1.1
[P1] isis 64
[P1-isis-64] network-entity 86.0010.0010.0100.1001.00
[P1-isis-64] is-level level-2
[P1-isis-64] cost-style wide
[P1-isis-64] is-name P1
[P1-isis-64] quit
[P1] interface loopback 0
[P1-LoopBack0] isis enable 64
[P1-LoopBack0] quit
[P1] interface gigabitethernet 1/0/0
[P1-GigabitEthernet1/0/0] isis enable 64
[P1-GigabitEthernet1/0/0] isis cost 5
[P1-GigabitEthernet1/0/0] quit
[P1] interface gigabitethernet 2/0/0
[P1-GigabitEthernet2/0/0] isis enable 64
[P1-GigabitEthernet2/0/0] isis cost 5
[P1-GigabitEthernet2/0/0] quit
[P1] interface gigabitethernet 3/0/0
[P1-GigabitEthernet3/0/0] isis enable 64
[P1-GigabitEthernet3/0/0] isis cost 5
[P1-GigabitEthernet3/0/0] quit
[P1] interface gigabitethernet 3/1/0
[P1-GigabitEthernet3/1/0] isis enable 64
[P1-GigabitEthernet3/1/0] isis cost 5
[P1-GigabitEthernet3/1/0] quit
# Configure PE1.
[PE1] router id 7.7.7.7
[PE1] isis 64
[PE1-isis-64] network-entity 86.0010.0070.0700.7007.00
[PE1-isis-64] is-level level-2
[PE1-isis-64] cost-style wide
[PE1-isis-64] is-name PE1
[PE1-isis-64] quit
[PE1] interface loopback 0
[PE1-LoopBack0] isis enable 64
[PE1-LoopBack0] quit
[PE1] interface gigabitethernet 1/0/0
[PE1-GigabitEthernet1/0/0] isis enable 64
[PE1-GigabitEthernet1/0/0] isis cost 5
[PE1-GigabitEthernet1/0/0] quit
[PE1] interface gigabitethernet 2/0/0
[PE1-GigabitEthernet2/0/0] isis enable 64
[PE1-GigabitEthernet2/0/0] isis cost 5
[PE1-GigabitEthernet2/0/0] quit
After the preceding configurations, run the display ip routing-table command on each node.
The command output shows that the nodes have learned routes from each other. For example,
when checking whether there are routes to the IP address of Loopback 0 on PE1, you can find
the following information:
Issue 02 (2014-09-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7 IS-IS Configuration
Table 7-3
and
Table
7-4.
702
Hide quick links:
Advertisement
