Subaru 1600 Service Manual page 625

NOTE:
a. Adjust gaps at front and rear
edges of the glass should be as
equal as possible.
b. If the gaps at the top and bottom
of pillar are not aligned, make
adjustment by shifting the regulator
channel B upward or downward.
In this case, confirm the gap at
top of glass, and check the upper
stoppers for uneven.contact.
@ Fitting pressure adjustment
1) Adjustment at window shoulder
a. Loosen nuts fixing the tops of
front and rear sashes, and make
adjustment by turning the bolt so
as to obtain following clearance
against the door inner flange.
CD-
Glass
2 Outer panel
3 Inner panel
'Fixing nut with
con ical spring washer
Adjust bolt
Approx. 1.3 mm
(0.051 in)/rev.
Adjustable length:
±
3.5 mm
(±
0.138 in)
14.5 mm (0.571 in)
A24·514
Fig. 14-90 Adjusting fitting pressure
at window shoulder
NOTE:
a. Since there is possibility of the
gaps at glass side edges being chang·
ed due to the shift of sash upon
loosening fixing nut of front
sash of 4-Door Sedan or Station
Wagon and of rear sash of 2-Door
Hatchback or Hardtop, it is recom·
mended to mark the original posi·
tion.
BODY
A24·515
Fig. 14-91 Marking sash position
b. In case of front door for 4-Door
Sedan and Station Wagon, turn
evenly two upper bolts of rear
sash so as to prevent rear sash
from inclination.
1 Bracket
2 Sash
Good
No good
Fig. 14-92 Adjusting sash
A24-516
Never incline the sash bracket
against the inner panel seat, other·
wise regulator operating force
might be increased significantly.
b. Confirm the relative position of
retainer and glass as shown below.
50
--'-'li..JL-.>~-,-,>!.!..!- _ _
.......Jw..L...
(1 .97)
~ ~
(;nGlaSS
~t
3 - 4 (Free set value)
Unit: mm (in) (0.12 - 0.16)
Fig. 14-93 Free set at window
shoulder
14-30
A24-517
NOTE:
Never provide free set of 5 mm (0.20
in) or more at the window shoulder.
Otherwise, the window shoulder might
be pressed excessively and glass top
inadequately when mounting roof side
weatherstrip.
2) Adjustment at the top of glass
Since free set changes due to
reaction force of roof side weather
strip, incline the glass to the inside
by adjusting the bolt at the bottom
of sash until the top of glass comes
near the inner flange of retainer.
Max. free set: II mm (0:43 in)
NOTE:
a. Never operate the upper adjust
bolt in this stage, otherwise regula·
tor operating force might be in·
creased due to incorrect adjust·
ment.
b. The bolts at the bottom of front
and rear sashes should be screwed
in the same direction and by the
same amount.
Adjustable length:
±
8 mm
(±
0.31 in)
3) After Adjustment Work
I) Install roof side weatherstrip se-
curely into the retainer, taking special
care of the corner.
2) Completely tighten all bolts and
nuts that have been tightened tem-
porarily.
4) Check
Check for the followings
I) If the glass won't enter the com·
partment side over the top of weather·
strip when raising or lowering the
glass.
If it enters, the free set at window
shoulder is too much. Make adjust.
ment with referring discreption on
adjustment
@.
"
" . ".1 •• 4 ''' .....
-~,..
....
I.-~.,.. .. ' - -...... ' .... , _ ..... , ........ , ... , -...
1 ..
-',..,.1------. . ,-,-----_--__________ _