Subaru 1600 Service Manual page 577

HEATING, VENTILATING AND AIR-CONDITIONING SYSTEM
~
19-21N·m
I
Torque
I
(Shaft nut)
(l.9 -
2.1 kg-m,
I
14 - 15 ft-lb)
~ _ _ _ _ _ _ J _ _ _ _ _ _ _ _ ~
6) Using a thic kness gauge, measure
the dutch hub-to-pulley clearance.
1-----·
Hub-to-pulley clearance:
~.------------------------~
0.5 - 0.8 mm
(0.020 - 0.031 in)
If the speciHed clearance is not ob-
tained, replace adjusting spacer and
readjust.
2) Condenser
S ~9~~;;-i;;gtorqUe
N'm (kg·m, ft·lb)
T.10-18(1.0-1.8,7-13)
...
_
.....
__
.
--------------------'
Fig. 13-78
1)
Renwve front grille and lower
slay.
2)
Discharge refrigerant.
3) Disconned grounding wiring from
radiator.
4)
Disconnect pipe connections.
5) Loosen two mounting bolts from
r<ldiator, and then take out condenser.
6) Condenser should be installed in
the reverse order of removal.
Fig. 13-77
NOTE:
When replacing compressor clutch
ASSY, do not forget break-in opera-
tion, accomplished by engaging and
disengaging the clutch some thirty
times. Break-in operation raises the
level of transmitted torque.
A26-126
, - - - - - - - - - - -
---_._--._------
Torque N·m (kg-m, tl-lb)
f - - - - - - - - - - - . - - - -
Left-hand
piping flare nut
- - - - - - -
15 - 25
(1.5
-~ 2.5,
11- 18)
f - - - - - - - - - - - - - - . -
f - - - - - - - -
Right-hand
piping flare nut
13-32
10 - 20
(1.0 - 2.0,
7 - 14)
Inspection
I) Make sure the condenser fins are
free from dust and insects.
I f the fins
are clogged, clean by blowing air or
water through them.
NOTE:
To prevent dust and water from
getting into the condenser, this work
work must be done when the con-
denser is installed in an actual vehicle.
2) Check all
of
the condenser's parts
to see if they show any sign of
oil
see-
page. Should oil ooze or gas leak from
a particular part, replace it with <l new
one.
3) Receiver Drier
Removal and installation
1) Drain the fluid from the washer
tank, remove the washer tank, and
then place it in the rear.
Fig. 13-79
A26-089
2) Discharge refrigerant.
3)
Disconnect the wiring from the
low-pressure switch.
4)
Disconnect two pipes.
5)
Loosen the two mounting bolts
and remove the receiver drier.
NOTE:
The receiver drier contains a desicant.
Be sure to put a blind plug in the
detached receiver drier to protect it
from moisture.
6) The receiver drier should be in·
stalled in the reverse order in which it
was removed.
IJ~
II
~"
I
*
·>,.,-1,,-"""'-,,!.,..,..,....._"' ..
~
...... , _ _ ..... ...,+I .........
oj_' ... , ...
r' ' ' ' ' · · ... ' ... ,_' ... , ___ .........
' t _ ...
'F .... , ...
qqq,_. ,." ..... , _____ - -____ , ..... _______ _