Subaru 1600 Service Manual page 380

REAR WHEEL DRIVING SYSTEM (4WD MODEL)
Rear
Pinion height adjusting washer thickness Part No.
differential 383495200 3.09mm (0.1217 in)
( continued) 383505200 3.12 mm (0.1228 in)
383515200 3.15 mm (0.1240 in)
383525200 3.18mm (0.1252 in)
383535200 3.21 mm (0.1264 in)
383545200 3.24 mm (0.1276 in)
383555200 3.27 mm (0.1287 in)
383565200
3.30 mm (0.1299 in)
383575200 3.33 mm (0.1311 in)
383585200
3.36 mm (0.1323 in)
383595200 3.39 mm (0.1335 in)
383605200 3.42 mm (0.1346 in)
383615200 3.45 mm (0.1358 in)
383625200 3.48 mm (0.1370 in)
383635200 3.51 mm (0.1382 in)
383645200 3.54 mm (0.1394 in)
383655200 3.57 mm (0.1406 in)
383665200 3.60 mm (0.1417 in)
383675200 3.63 mm (0.1429 in)
383685200 3.66 mm (0.1441 in)
Side gear to thrust washer clearance
0.1 - 0.2 mm (0.004 - 0.008 in)
Side gear thrust washer thickness Part No.
383445201 0.75 - 0.80 mm (0.0295 - 0.0315 in)
383445202 0.80 - 0.85 mm (0.0315 - 0.0335 in)
383445203 0.85 - 0.90 mm (0.0335 - 0.0354 in)
Side bearing standard width
20.00 mm (0.7874 in)
Side bearing retainer shim thickness Part No.
383475201 0.20 mm (0.0079 in)
383475202 0.25 mm (0.0098 in)
383475203 0.30 mm (0.0118 in)
383475204 0.40 mm (0.0157 in)
383475205 0.50 mm (0.0197 in)
Drive gear to drive pinion backlash 0.10 - 0.20 mm (0.0039 - 0.0079 in)
Drive gear runout on its back surface Limit
0.05 mm (0.0020 in)
Oil capacity 0.8 Q (1.7 US pt, 1.4 Imp pt)
Propeller Tube runout Limit 0.6 mm (0.024 in)
shaft Joint bending resistance Maximum 1.5 N·m (I5 kg.cm, 13 in.lb)
Axial play of journal 0.02 mm (0.0008 in) or less
Axial play adjusting snap ring thickness
Part No. Paint color
622033000
White 2.00 ± 0.01 mm (0.0787
±
0.0004 in)
622033010 Yellow 2.02
± 0.01 mm (0.0795 ± 0.0004 in)
622033020 Red 2.04 ±
om
mm (0.0803
±
0.0004 in)
622033030 Green 2.06
± 0.01 mm (0.0811 ± 0.0004 in)
622033040 Blue 2.08
±
0.01 mm (0.0819
±
0.0004 in)
622033050
Light Brown
2.10
± 0.01 mm (0.0827 ± 0.0004 in)
622033060 No paint 2.12
±
0.01 mm (0.0835
±
0.0004 in)
622033070 Pink 2.14
± 0.01 mm (0.0843 ± 0.0004 in)
8-3
----!