Download Print this page

GRAPHTEC CE6000 SERIES User Manual: Setting The Tool Condition

Graphtec ce6000 series cutting plotter.
Hide thumbs

Advertisement

Setting the Tool Condition

This section describes how to make the tool, speed, force,
acceleration, and tool number settings. Before cutting media, the
following five cutter-pen conditions must be specified.
(1) Cutter-blade length . ... Adjust the blade length by referring to the
(2) FORCE . ..................... Set the FORCE by referring to the table
(3) SPEED ...................... Set the SPEED by referring to the table
(4) ACCELERATION . ...... Set the ACCELERATION by referring to
(5) OFFSET .................... Set to suit the cutter blade being used.
CAUTION
It may result to damaging the cutter blade or the cutting mat if the blade is extended too much. Make sure the blade length is set
less than the thickness of the media.
Tool Conditions (Cutter Blade) for Each Media Type
Media type
Film for outdoor use
Film for decorative use
Transparent or semitransparent film
Reflective film
Fluorescent film
Car film
Tool Conditions for Each Media Type (Simple mode: initial value)
Media type (LCD indications)
Film for outdoor use (For outdoor use)
Film for decorative use (For decorative use)
Transparent or semitransparent film (Transparent film)
Reflective film (Reflective film)
Fluorescent film (Fluorescent film)
Blade Part Nos., Displayed Blade Types, and CUTTER OFFSET Values
Blade material/tool
Ultra-hard blade
Other
Pen
When a blade type has been selected, the OFFSET is automatically adjusted by ±5 with respect to the default
cutter offset value for that blade type.
Select OTHER to use settings other than those displayed for hard-to-cut media.
Select pen to set the plotting pen.
media thickness table below.
below.
below.
the table below.
Thickness (mm)
0.05 to 0.08
0.08 to 0.1
0.08 to 0.1
0.08 to 0.1
0.20 to 0.25
0.05 to 0.08
Blade type
CB09UB
CB09U
CB15U
CB15U
CB15UB
CB15UB
CB09UB-K60
CB09U-K60
OTHER
PEN
Blade used
CB09UB
CB09UB
CB09UB
CB09UB
CB09UB, CB15U
CB09UB-K60
Blade used
CB09UB
CB09UB
CB09UB
CB09UB
CB09UB
LCD panel indication
Blade (tool) type
2-34
Supplement
See the appropriate references for details
about the "Setting the Tangential Emulation"
, "Setting Length of the Overcut"
P.7-3
, "Setting the Distance Adjust"
P.7-4
, and "Setting of the Initial Down
P.7-14
Force"
.
P.7-6
For method to manually adjust the blade
length, see "Adjust the Blade Length
Manually"
P.2-44
Length Automatically"
Force
Speed (cm/s)
10 to 14
30 or under
14 to 17
30 or under
14 to 20
30 or under
14 to 20
30 or under
20 to 24
10 to 20
14 to 20
5 to 15
Standard Value
with Cut Pressure
Speed (cm/s)
(Force)
(12)+0
(15)+0
(17)+0
(17)+0
(22)+0
Setting
range
Default value
0
±5
0
±5
0
±5
0
±5
1
1 to 45
N/A
N/A
and "Adjust the Blade
.
P.2-48
Acceleration
2
2
2
2
2
2
20
20
20
20
15
Setting value
for other
19
29
7
19
0

Advertisement

   Also See for GRAPHTEC CE6000 SERIES

Comments to this Manuals

Symbols: 0
Latest comments:
  • Jishad Jan 10, 2018 08:16:
    my graphtec ce 6000-60 showing an error message
    Hardware illegal code. Can you solve this
  • sina oyekunle Dec 21, 2017 02:44:
    my graphtec ce 6000-60 showing an error message: check cam_b-pcb
  • jitendra solanki Jun 14, 2017 05:31:
    i want ce6000 series user manual pdf file