Comtech EF Data CDM-425 Installation And Operation Manual page 387

Command
Number of
Parameter (Instruction
Arguments
& Qualifier)
Packet PPE= 1 byte,
Processor 0 or 1
Card Enable
QoS Mode QOS= 2 bytes each,
0 thru 3
Switch Ports SPC= 47 bytes
Configuration
Edit entry in SVE= 8 bytes
VLAN table
Packet WMD= 1 byte,
Processor 0 thru 3
Working Mode
Serial Remote Control
Description of Arguments
Command or Query.
Sets or returns Packet Processor Card operation in the form x, where:
0=Packet Processor Card is Disabled
1=Packet Processor Card is Enabled
NOTE: Change of this configuration results in modem auto-reboot only when IP Packet Processor option
card is installed and enabled. Otherwise, when the IP Packet Processor option card is not installed, this
selection is stored but is otherwise non-functional.
Command or Query.
Sets or returns QoS (Quality of Service) Mode in the form ab, where:
a=Layer 2 QoS:
0=Off, Layer 2 QoS is disabled
1=VLAN Priority only
2=Port Priority only
3=VLAN and Port Priority
b=Layer 3 QoS:
0=Off, Layer 3 QoS is disabled
1=Advanced QoS Max / Priority (requires Advanced QoS FAST Option)*
2=Advanced QoS Min Max (requires Advanced QoS FAST Option)*
3=Advanced QoS DiffServ (requires Advanced QoS FAST Option)*
*NOTE: Layer 3 QoS settings 1 through 3 apply to modem only with IP Packet Processor option card
installed and enabled.
Command or Query.
Sets or returns Ethernet switch ports' priority and PVID in the form
1abccccdxxx;2abccccdxxx;3abccccdxxx;4abccccdxxx, where:
1, 2, 3, or 4=Port number.
a=Port priority: Value=1, 2, 3 or 4 (the higher the number, the higher the priority).
b=Port Native Mode: 0=Native Mode Disabled, 1=Native Mode Enabled.
cccc=Port VLAN ID: Value range=0000-4095 – Value 0000 is only valid when port Native Mode is
disabled.
d=Pause flow control. 0=Off, 1=On
xxx=Reserved.
Command only.
Edit VLAN table entry in the form aaaabcde, where:
aaaa=existing VLAN ID – Value range is 0001-4095.
b=property of port 1: 0=Tagged, 1=Filtered, 2=Untagged
c=property of port 2: 0=Tagged, 1=Filtered, 2=Untagged
d=property of port 3: 0=Tagged, 1=Filtered, 2=Untagged
e=property of port 4: 0=Tagged, 1=Filtered, 2=Untagged
Command or Query.
Sets or returns Packet Processor Working Mode in the form x, where:
0=Managed Switch
1=Router Point to Point*
2=Router Multipoint Hub*
3=Router Multipoint Remote*
*NOTE: Settings 1 through 3 apply to modem only with IP Packet Processor option card installed and
enabled.
8–63
CDM-425 Advanced Satellite Modem
Revision 0
Query
Response to
(Instruction Response to Query
Command
& Qualifier)
PPE= PPE? PPE=x
PPE? (see Description of
PPE* Arguments)
PPE#
QOS= QOS? QOS=ab
QOS? (see Description of
QOS* Arguments)
QOS#
SPC= SPC? SPC=1abccccdxxx,2ab
SPC? ccccdxxx,3abccccdxxx,
SPC* 4abccccdxxx
SPC# (see Description of
Arguments)
SVE= N/A SVE=aaaabcde
SVE? (see Description of
SVE* Arguments)
SVE#
WMD= WMD? WMD=x
WMD? (see Description of
WMD* Arguments)
WMD#
MN-CDM-425