Page 1
___________________ SCALANCE XM-400/XR-500 Command Introduction Line Interface ___________________ General information ___________________ Configuration SIMATIC NET Functions specific to ___________________ SCALANCE Industrial Ethernet switches ___________________ SCALANCE XM-400/XR-500 System time Command Line Interface ___________________ Network structures Configuration Manual ___________________ Network protocols Layer 2 management...
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
3.1.1.10 show pnio ............................. 48 3.1.1.11 show broadcast-block config ......................49 3.1.1.12 show unicast-block config ......................49 3.1.1.13 show multicast-block config ......................50 3.1.1.14 show versions ..........................51 3.1.2 clear counters ..........................51 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 4
............................84 3.2.6.2 tftp filename ..........................85 3.2.6.3 tftp load............................86 3.2.6.4 tftp save ............................87 3.2.6.5 tftp server ............................ 88 Reset and Defaults ........................89 3.3.1 restart ............................89 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 5
Commands in the global configuration mode ................115 4.4.2.1 set signaling contact mode ......................115 4.4.2.2 set signaling contact status ......................116 System time ............................117 System time setting ........................117 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 6
6.1.2.1 interface range .......................... 149 6.1.2.2 no interface range ........................150 6.1.2.3 map protocol ..........................151 6.1.2.4 no map protocol ........................152 6.1.2.5 protocol-vlan ..........................153 6.1.2.6 no protocol-vlan ......................... 153 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 8
........................232 Network protocols ..........................233 IPv4 protocol ..........................233 7.1.1 show ip route ..........................233 7.1.2 show ip static route ........................234 7.1.3 show ip gateway ........................234 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 9
........................ 264 7.3.4.2 no ip dhcp relay circuit-id ......................265 7.3.4.3 ip dhcp relay remote-id ......................266 SNMP ............................267 7.4.1 The "show" commands ......................267 7.4.1.1 show snmp ..........................267 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 10
..........................301 HTTP server ..........................302 7.6.1 show ip http server status ......................302 7.6.2 Commands in the global configuration mode................302 7.6.2.1 ip http ............................303 7.6.2.2 no ip http............................ 304 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 11
......................... 333 8.4.3 show hrp counters ........................334 8.4.4 show ring-redundancy ........................ 334 8.4.5 Commands in the global configuration mode ................335 8.4.5.1 ring-redundancy configuration ....................335 8.4.5.2 ring-redundancy mode ....................... 336 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 12
9.3.12.1 router ospf ..........................369 9.3.12.2 no router ospf ..........................370 9.3.13 Commands in the Router Configuration mode................371 9.3.13.1 ASBR Router ..........................371 9.3.13.2 no ASBR Router ........................372 9.3.13.3 area range ..........................373 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 13
............................. 415 9.4.2.2 no router rip ..........................416 9.4.3 Commands in the RIPv2 Router configuration mode ..............416 9.4.3.1 auto-summary ..........................417 9.4.3.2 no auto-summary ........................417 9.4.3.3 distance ............................418 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 14
Commands in the interface configuration mode ............... 455 10.1.2.1 rate-limit output ......................... 455 10.1.2.2 no rate-limit output ........................456 10.1.2.3 storm-control ..........................456 10.1.2.4 no storm-control ........................458 10.1.2.5 storm-control level ........................459 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 15
11.3.3 Commands in the global configuration mode ................487 11.3.3.1 mac access-list extended ......................488 11.3.3.2 no mac access-list extended ...................... 489 11.3.4 Commands in the interface configuration mode ................ 489 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 16
11.7.4.2 no dot1x guest-vlan ........................528 11.7.4.3 dot1x mac-auth ......................... 529 11.7.4.4 no dot1x mac-auth ........................530 11.7.5 Commands in the interface configuration mode ............... 530 11.7.5.1 dot1x guest-vlan ........................530 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 17
12.1.14.13 no link ............................ 564 12.1.14.14 syslogserver .......................... 565 12.1.14.15 no syslogserver ........................566 12.2 Syslog client ..........................568 12.2.1 show events syslogserver ......................568 12.2.2 Commands in the Events configuration mode ................568 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 18
12.5.4.3 no loopd port reset ........................599 12.5.4.4 loopd reaction local ........................599 12.5.4.5 no loopd reaction local ......................600 12.5.4.6 loopd reaction remote ....................... 601 12.5.4.7 no loopd reaction remote ......................602 Index ..............................603 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This Configuration Manual applies to the following software versions: ● SCALANCE XR-500 firmware as of version 4.1 ● SCALANCE XM-400 firmware as of version 4.1 Purpose of the Configuration Manual This Configuration Manual is intended to provide you with the information you require to install, commission and operate IE switches.
Page 20
Apart from the configuration manual you are currently reading, the products also have the following documentation: ● Configuration Manual: – SCALANCE XM-400/XR-500 Web Based Mangement This document is intended to provide you with the information you require to commission and configure IE switches using Web Based Management.
Page 21
Siemens recommends strongly that you regularly check for product updates. For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept.
Page 22
Introduction 1.1 Information on the configuration manual (CLI) SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Even commands that bring about fundamental changes to the configuration are executed without a prompt for confirmation. Errors in the configuration can mean that no further operation is possible in the entire network. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
It is not possible to modify parameters in this mode. To be able to modify configuration parameters, you need to change to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 25
From the Global Configuration mode, you can change to other configuration modes for special tasks. These are either general configuration modes (for example line configuration, interface configuration) or protocol-specific configuration modes (SNTP, NTP). SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Management ACLs (access rules for management) Rules for port ACL MAC Ingress and egress rules for port ACL MAC Rules for port ACL IP Ingress and egress rules for port ACL IP SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 27
OSPF interfaces per OSPF area OSPF virtual links (within an autonomous system) OSPF interface authentication key (40 interfaces each with 5 keys) OSPF virtual link authentication key (8 virtual links each with 5 keys) SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Make sure, however, that names used by the operating system or other programs are correctly written. Blank To use blanks in a text, enter the text in quotes, for example "H e l l o" SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you use the keyword, you need to specify exactly one of the values "A", "B" or "C" keyword { [A] [B] [C] } After the keyword, enter one or more of the values "A", "B" or "C" SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● Multicast addresses Layer 2 multicast addresses as used on this device use the notation of MAC addresses. For permitted address ranges, check the rules or ask your network administrator. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● a fixed RJ-45 port ● an SFP transceiver slot that can be equipped individually Of these two ports, only one can ever be active. You can set the active port with the command media-type SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 32
Type of interface Command prompt cpu0 cli(config-if-cpu0)# vlan cli(config-if-vlan-$)# port-channel cli(config-if-po-$)# gigabitethernet cli(config-if-Gi$-$)# extreme-ethernet cli(config-if-Ex$-$)# Router-Port cli(config-RPort-Gi$-$)# The placeholders denote the numbering of the interface. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are then in the Privileged EXEC mode. Requirement You are in a configuration mode. Syntax Call the command without parameters: Result You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● Command completion with the tab key ● Automatic completion of incomplete commands ● Paging in the list of most recently used commands ● Display of the list of most recently used commands ( show history SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Both the mode-specific as well as the global commands are displayed. Note Incomplete command names If you have specified an incomplete command when calling help, a list of all commands that start with the term you have entered is created. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
-- more -- the display, you can move to the next page with the spacebar. If the display is in pages, you cannot page back. You exit the page display with the key. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If the entry is not yet complete, enter further characters. With , you obtain a list of the possible commands. Repeat this if necessary until the command is complete and can execute. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If the command you are looking for is displayed, you can edit the command line as required and execute the command with the enter key. Further notes You display the list of commands last used with the command. This function is show history available in every mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
CLI#conf t; int gi 1/1; shut; no switchport; no shut; no ip address; end; write startup has the same effect as: CLI#conf t CLI(config)#int gi 1/1 CLI(config-IF-gi1-1)#shutdown CLI(config-IF-gi1-1)#no switchport CLI(config-IF-gi1-1)#no shutdown CLI(config-IF-gi1-1)#no ip address CLI#write startup SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show history Result The list of used commands is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show cli-console-timeout Result The configuration for the timeout is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show device information Result The information about the device is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Syntax Call the command without parameters: show hardware Result The table of interface cards is displayed. The slot ID, the status and the type or name of the card is listed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For further information on the media modules, refer to the compact operating instructions of the MM900 media modules for SCALANCE XR-500M. Result The settings are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameters from the parameter list, the status and configuration of all available interfaces will be displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
(Page 30)". If you do not select any parameter from the parameter list, the entries are displayed for all available counters. Result The counters of the selected interfaces are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
(Page 30)". If you do not select any parameter from the parameter list, the configuration is displayed for all available IP interfaces. Result The configuration of the selected IP interface is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show pnio Result The current PROFINET IO configuration is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows the unicast blocking settings for ports. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Range of values port Keyword for a port description interface-type Type of interface • gigabitethernet • extreme-ethernet interface-id Slot no. and port no. of the interface Enter a valid interface name SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The version information of the entire system is displayed. 3.1.2 clear counters Description With this command, you reset the counters of an interface. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you change to the Global configuration mode. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# Syntax Call the command without parameters: configure terminal SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: disable Result You are in the User EXEC mode. The command prompt is as follows: cli> 3.1.5 enable Description With this command, you change to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Syntax Call the command without parameters: lock Result The console is locked. The system expects the entry of the password. Further notes You cancel the lock by entering the Login password. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call up the command with the following parameters: ping [ip]<destination-address> [size<packet_size(0-2080)>] [count<packet_count(1-10)>] [timeout<time_out(1-100)>] SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you close a console session on the device. With the option, you close a session and that is not reacting. forceful-clear Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
There you can edit the settings for one interface. You select the interface with the parameters of this command. If you specify a logical interface that does not exist, it will be created. The name of the selected interface is displayed in the command prompt. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 58
The ranges of values for the logical interfaces VLAN and port channel can be found in the table above. You can only call up interfaces that you created with the vlan channel-group command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The logical interface is deleted. Further notes You configure an interface with the command. interface You display the status and the configuration of the interfaces with the show interfaces command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The time is configured and automatic logout is enabled. Further notes You disable automatic logout with the command. no cli-console-timeout You display the current timeout setting with the command. show cli-console-timeout SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you enter a height coordinate. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: coordinates height <meter> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Input box for the latitude max. 32 characters coordinate To use spaces in the entry, enter the latitude coordinate in quotes: coordinates latitude "123 456" Result The latitude coordinate is created. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you enter contact information for the system. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
<string> The parameter has the following meaning: Parameter Description Note string Input box for the location information max. 255 characters Result The location information is created in the system. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you change the password of a user. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: username {user|admin}password<passwd> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the Interface configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you configure the duplex mode of an interface. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: no duplex Result The duplex mode of the Interface is reset to the default value. Further notes You configure the duplex mode of the interface with the command. duplex SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can shut down the interface with the command. shutdown You display this setting with the command. show interface mtu You display this setting and other information with the command. show interfaces SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable autonegotiation of connection parameters on an interface. Requirement You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no negotiation SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The blocking of broadcast frames is disabled. Default: disabled Result The blocking of broadcast frames is enabled / disabled. 3.1.11.8 set multicast-block Description With this command, you enable / disable the blocking of multicast frames on an interface. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The Interface is shut down. A connection continues to be indicated if a switch port is turned off. The LED for the port status flashes 3 times cyclically. However no data is sent or received. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The Interface is activated. Further notes You activate the interface with the command. shutdown You can display the status of this function and other information with the show command. interfaces SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Transmission speed 1000 Mbps Result The transmission speed of the interface is configured. 3.1.11.12 switchport Description With this command, you configure the interface as a switch port. Requirement ● The Interface is shut down. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no switchport Result The interface is configured as a router port. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The receipt of LLDP packets is enabled. Default: enabled Note Enabling both options When you call this command, you can only select one option. If you want to enable both options, call up the command again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you want to disable both options, call up the command again. Result The setting is configured. Further notes You enable the sending or receipt of LLDP packets with the command. lldp SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
In this mode, the SFP transceiver port is used independent of the fixed RJ-45 port. If an RJ-45 connection is established, it is terminated because the power of the RJ- 45 port is turned off. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 79
Configuration 3.1 System Result The mode of the combo port is configured. Further notes You display the mode of a combo port with the command and the parameter show interface description SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The current Load&Save file information is displayed. 3.2.2 show loadsave tftp Description This command shows the current Load&Save TFTP server configuration. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The current Load&Save TFTP server configuration is displayed. 3.2.3 load tftp Firmware The firmware is signed and encrypted. This ensures that only firmware created by Siemens can be downloaded to the device. Description With this command, you load the files from a TFTP server.
Shows that the name follows that will be assigned to the file type filename Name of the file max. 100 characters Result The file is saved on the TFTP server. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: loadsave Result You are now in the LOADSAVE configuration mode. The command prompt is as follows: cli(config-loadsave)# Further notes You exit the LOADSAVE configuration mode with the command. exit SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Shows the available files filetype Shows that the file type follows that will be deleted filetype Name of the file type max. 100 characters Result The files are displayed or the file is deleted. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Shows that the name follows that will be assigned to the file type filename Name of the file max. 100 characters Result The file types are displayed or the file type is assigned a name. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
3.2.6.3 tftp load Firmware The firmware is signed and encrypted. This ensures that only firmware created by Siemens can be downloaded to the device. Description With this command, you load a file from a tftp server into the file system of the device. The tftp protocol is used for the transfer.
Name of the file type max. 100 characters Result The file types are displayed or the file is copied. Further notes You configure the name of the file with the command. tftp filename SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
TFTP connection runs tcp port Parameter 1 … 65535 For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The settings are configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● if no parameters are specified: restarts the system with the current configuration Parameter Description factory Restarts the system with the factory configuration settings Result The device is restarted with the selected settings. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Shows the configuration settings of the Syslog function dhcp shows the configuration settings of the Dynamic Host Configuration Protocol Shows the configuration settings of the Spanning Tree protocol Shows the configuration settings of the Link Aggregation function SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 91
Shows the configuration settings of the system time Shows the configuration settings of the Network Time Protocol auto-save Shows the configuration settings of the auto save function panel-button Shows the configuration settings of the Panel Button function SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement ● The Trial mode is activated. You are in the Privileged EXEC mode. The command prompt is as follows: *cli(...)# Syntax Call the command without parameter assignment: write startup-config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You save the changes to the configuration with the command. write startup-config With the command, you enable the auto save function. auto-save Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The auto save function is disabled. The Trial mode is disabled. Further notes You enable the function with the command. auto-save You can display the status of this function and other information with the show device command. information SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
E.g. 1/2 for slot 1, port 2 separated by a slash Note Calling commands without parameters If you use the command without setting parameters, information about all PoE interfaces is displayed. Result The information is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
An event is also entered in the logbook. Requirement You are in the Global Configuration mode. The command prompt is as follows: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: poe pse usage Result Usage Threshold is set to 80%. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config-if-Gi$-$)# The placeholders $-$ stand for the numbering of the interface. Syntax Call the command without parameters: poe active Result PoE is activated for the corresponding interface. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Interface Configuration mode of a PoE interface. The command prompt is as follows: cli(config-if-Gi$-$)# The placeholders $-$ stand for the numbering of the interface. Syntax Call up the command with the following parameters: poe type <string> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you specify the priority of the power supply for an interface. Requirement You are in the Interface Configuration mode of a PoE interface. The command prompt is as follows: cli(config-if-Gi$-$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The placeholders $-$ stand for the numbering of the interface. Syntax Call the command without parameters: no poe prio Result The priority of the corresponding interface has been set to "low". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show nfc active status Result The status of the NFC function is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Further notes You deactivate NFC with the command. no nfc active You display the status, i.e. whether the NFC function is activated or deactivated with the command show nfc active status SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
NFC is deactivated. Further notes You activate NFC with the command. nfc active You display the status, i.e. whether the NFC function is activated or deactivated with the command show nfc active status SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show plug Result The current information of the C-PLUG or KEY-PLUG is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands in the C-PLUG configuration mode This section describes commands that you can call up in the Plug Configuration mode. In the Global Configuration mode, enter the command to change to this mode. plug SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you format the C-PLUG or KEY-PLUG and copy the current device configuration to it. Requirement ● The C-PLUG or KEY-PLUG is formatted. You are in the Plug Configuration mode. The command prompt is as follows: cli(config-plug)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 108
Functions specific to SCALANCE 4.1 C-PLUG Syntax Call the command without parameter assignment: write Result The current device configuration has been copied to the formatted C-PLUG or KEY-PLUG. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The time is configured and automatic logout is enabled. Further notes You disable automatic logoff with the command. no web-session-timeout You display the current timeout setting with the command. show web-session-timeout SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no web-session-timeout Result Automatic logoff is disabled. Additional notes You enable automatic logoff with the command. web-session-timeout SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameters have the following meaning: Parameter Description enable Enables the function for restarting with factory settings Default: enabled disable Disables the function for restarting with factory settings SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Default: enabled disable disables the function for setting the fault mask Result The function of the "SELECT/SET" button for setting the fault mask is enabled / disabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show signaling-contact Result The current configuration of the signaling contact is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The signaling contact can be opened or closed as required by user actions. Result The reaction of the signaling contact is specified. Further notes You display the setting with the command. show signaling contact SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description open Signaling contact is opened. close Signaling contact is closed. Result The signaling contact is opened or closed. Further notes You display the setting with the command. show signaling contact SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows all the entries for daylight saving time stored on the device. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The system time is entered by the user The system time is obtained from an NTP server sntp The system time is obtained from an SNTP server SINEC The system time is obtained using the SIMATIC time protocol SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Year 2000 ... 2035 Result The system time is set. Further notes You display the settings for the system clock with the command. show time SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Keyword for the end of daylight saving time. MMDDhh Time for the end of daylight saving time. Time in the format Month Hour Result The entry for the start and end of daylight saving time was created. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Hour 0 ... 23 Keyword for the end of daylight saving time. Result The entry for the start and end of daylight saving time was created. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameter has the following meaning: Parameter Description Range of values name Name of the entry maximum 16 characters Result An entry or the entries for the start and end of daylight saving time was/were deleted. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the NTP configuration mode with the command, you return to the Global exit configuration mode. ● If you exit the NTP configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The connection to a server is configured on the NTP client. Further notes You delete the connection to a server with the command. no ntp server SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Domain name (Fully Qualified Domain Name) Maximum of 100 characters Result The connection to a server is deleted on the NTP client. Further notes You configure the connection to a server with the command. ntp server SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Number of minutes difference Enter the number of hours and number of minutes with two digits each. Default: No time difference. Result The time difference between the device and the NTP server is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows the current configuration of the unicast mode of SNTP. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the SNTP configuration mode with the command, you return to the Global exit configuration mode. ● If you exit the SNTP configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You display the settings for the unicast mode with the show sntp unicast-mode status command. You display the settings for the broadcast mode with the show sntp broadcast-mode status command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The time zone of the system time of day is configured. Further notes You can display the settings of this function and other information with the show sntp command. status SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Default: 64 Result The polling interval of the SNTP client in unicast mode is configured. Further notes You display this setting and other information with the show sntp unicast–mode status command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The SNTP unicast server is configured. Further notes You can reset the setting to the default with the command. no sntp unicast-server You display this setting and other information with the show sntp unicast–mode status command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The SNTP unicast server is reset to the default value. Further notes You configure the setting with the command. sntp unicast-server ipv4 You display this setting and other information with the show sntp unicast–mode status command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 136
System time 5.3 SNTP client SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● Improved reliability by adapting the tree structure if transmission is disrupted (Spanning Tree) ● Splitting up of the network into smaller units that are connected together via managed connection pairs (standby connection) SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the entries are displayed for all available interfaces. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the entries are displayed for all available interfaces. Result The entries are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the entries are displayed for all available interfaces. Result The entries are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the entries are displayed for all available interfaces. Result The entries are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the entries are displayed for all available interfaces. Result The entries are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Number of the addressed VLAN 1 ... 4094 If you do not select any parameter from the parameter list, the total number of entries is displayed for all VLANs. Result The number is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you do not select any parameter from the parameter list, all entries are displayed. For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The entries are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows all the global information that is valid for all VLANs. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Number of the addressed VLAN or VLAN range 1 ... 4094 If you do not select any parameter from the parameter list, the entries of all available interfaces are displayed. Result The settings are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the entries of all available interfaces are displayed. Result The information is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The interfaces or interfaces of VLANs were put together to form an interface range. The following configuration commands apply to this range. Further notes With the command, you remove VLANs from this range or break it up. no interface range SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
5 - 10 Result The VLANs are removed. Further notes With the command, you can put several interfaces or VLANs together to be interface range able to configure them together. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The protocol group is created. Further notes You delete the protocol group with the command. no map protocol You can display the status of this function and other information with the show vlan command. protocols-group SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The protocol is removed from all protocol groups. Further notes You create the protocol group with the command. map protocol You can display the status of this function and other information with the show vlan command. protocols-group SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable the protocol-based classification on all interfaces. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no protocol-vlan SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can display the status of this function and other information with the show vlan device command. info 6.1.2.8 no subnet-vlan Description With this command, you disable the subnet-based VLAN classification on all interfaces. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: vlan <vlan-id(1-4094)> The parameter has the following meaning: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call up the command with the following parameter: no vlan <vlan-id(2-4094)> Parameters Description Range of values vlan-id Number of the addressed VLAN 2 ... 4094 The VLAN with number 1 cannot be deleted. Result The VLAN is deleted SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Range of values / note ip-subnet- IP subnet address Enter a valid subnet address address mask Subnet mask aaa.bbb.ccc.ddd vlan Keyword for a VLAN vlan-id Number of the addressed VLAN 1 ... 4094 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you do not select any parameters from the parameter list, the default value is used. For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can reset the setting to the default with the no switchport acceptable-frame-type command. You can display the status of this function and other information with the show vlan port command. config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you assign a VLAN to the interface and configure the port VLAN identifier (PVID) for it. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no switchport access vlan Result The setting is reset to the default value. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The group is assigned to the port and the VLAN. Further notes You delete the setting with the command. no switchport map protocols-group You can display the status of this function and other information with the show vlan command. protocols-group SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you specify the operating mode for the switch port. Requirement ● The interface is configured as a switch port. You are in the Interface configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you reset the operating mode for the switch port to the default. The default value is Hybrid. Requirement ● The interface is configured as a switch port. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call up the command with the following parameters: switchport priority default <0-7> The parameter has the following meaning: Parameter Description Range of values Value for the default priority 0 ... 7 Default: 0 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
(PVID) for it. If a received frame has no VLAN tag, it has a tag added with the VLAN-ID specified here and is sent according to the switch rules for the port. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The default value is 1. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no switchport pvid SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
VLAN ID is removed. ● Forbidden ports This interface is not used for communication in a VLAN The "tagged port" and "untagged port" you specify with this command are used for outgoing data traffic. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 169
Keyword for the name assignment vlan-name Name of the VLAN max. 32 characters For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config-vlan-$$$)# Syntax Call up the command with the following parameters: no ports [<interface-type><0/a-b,0/c,...>] [<interface-type><0/a-b,0/c,...>] [port-channel<a,b,c-d>] [all] untagged<interface-type> <0/a-b,0/c,...> [<interface-type><0/a-b,0/c,...>] [port-channel <a,b,c-d>] [all] forbidden<interface-type><0/a-b,0/c,...> [<interface-type><0/a-b,0/c,...>] [portchannel<a,b,c-d>] [all] SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
6.1.4.3 name Description With this command, you assign a name to the VLAN. Requirement You are in the VLAN Configuration mode. The command prompt is as follows: cli(config-vlan-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config-vlan-$$$)# Syntax Call the command without parameters: no name Result The name of the VLAN is deleted. Further notes You assign the VLAN a name with the command name SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The TIA interface is enabled exclusively for the specified VLAN. The function was disabled on the other interfaces. Further notes Note that only one VLAN interface can become the TIA interface. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● As long as a VLAN is configured as a transparent VLAN, the ports belonging to this VLAN cannot be modified. ● Note that only one VLAN can become a transparent VLAN. You disable the setting with the command. no transparent-vlan SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● The port VLAN ID of the previous transparent ports remains set to the ID of this VLAN. ● All other ports remain marked as forbidden in this VLAN. Further notes You enable the setting with the command. transparent-vlan SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Specification of the protocol set for a channel-group If you do not select any parameters from the parameter list, the settings of all channels will be displayed in detail. Result The Etherchannel settings are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description This command shows the information about the settings and information about the ports involved in the link aggregation. The number of sent and received packets is also displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can reset the setting for the load balancing policy to the default with the no port-channel command. load-balance You can display the status of this function and other settings with the show etherchannel command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can change the setting for the load balancing policy with the port-channel load-balance command. You can display the status of this function and other settings with the show etherchannel command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This corresponds to manual bundling. active The negotiation of a connection via LACP is started unconditionally passive The negotiation of a connection via LACP is started when an LACP packet arrives from the connection partner SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no channel-group Result The interface is deleted from the Etherchannel. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Shows the blocked ports pathcost method shows whether 16-bit (short) or 32 bit (long) values are used in the calculation Result The settings for the spanning tree function are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Range of values instance-id Number of the instance or range of instances whose 1 ... 64 settings are displayed detail Shows detailed information about the selected interface Result The settings are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows the settings of the spanning tree function of the bridge. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show spanning-tree detail Result The detailed settings for the spanning tree function are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Shows detailed information about the spanning tree settings of the interface. For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Slot no. and port no. of the interface Enter a valid interface name For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The settings are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Shows the interface via which the spanning tree is set up priority Shows the priority of the bridge detail Shows detailed information about the root bridge Result The settings of the root bridge for the spanning tree function are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call up the command with one of the following parameter assignments: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you restart the protocol transmission process on a specific or on all interfaces and force renegotiation of the connection settings with the neighboring devices. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: clear spanning-tree counters Result The counters are reset. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can display the status of this function and other information with the show spanning tree command. detail You can display information about active ports with the show spanning tree active command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you configure the compatibility version of the protocol that will be used by the spanning tree function. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The default value is MST. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no spanning-tree compatibility SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can only change the value for the priority in the steps of 4096. Result The priority of the device is configured. Further notes You can reset the setting to the default with the command. no spanning-tree mst priority SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You display this setting and other information with the commands that start with show spanning tree ... 6.3.4.7 spanning-tree mst configuration Description With this command, you change to the MSTP configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: spanning-tree mst max-hops <value(6-40)> The parameter has the following meaning: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The setting for the maximum number of nodes is reset to the default value. Further notes You can configure the setting for the maximum number of nodes with the spanning-tree mst command. max-hops SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Further notes You disable the root bridge with the command. no spanning-tree mst instance-id root You display this setting and other information with the commands that start with show spanning tree ... SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Further notes You enable the root bridge function with the command. spanning-tree mst instance-id root You display this setting and other information with the commands that start with show spanning tree ... SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
1 ... 2 Default: 2 max-age Keyword for the time after which the information of the BPDUs becomes invalid seconds Maximum age of the BPDUs in seconds 6 ... 40 Default: 20 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 203
2 seconds max-age 20 seconds Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: no spanning-tree{forward-time|hello-time|max-age} SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the Interface configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Describes the costs of the port for calculating the Default: lowest cost path. if dynamic calculation of the path costs is not enabled: 200000 for physical • interfaces 199999 for port channels • SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 206
You can reset the setting to the default with the (properties) command. no spanning-tree You display these settings and other information with the commands that start with show spanning tree ... SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Keyword for the costs of the port for calculating the lowest-cost path. disable Enables the interface for spanning tree. link-type Connection status of the following network segment portfast Disables the PortFast function. port- Keyword for the priority of the interface priority SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call up the command with the following parameters: spanning-tree mst<instance-id(1-64)> {cost(0-200000000)|port-priority (0-240)|disable} SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You display these settings and other information with the commands that start with show spanning tree ... 6.3.5.4 no spanning-tree mst Description With this command, you reset the various properties of the multiple spanning tree function to the default value. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 210
The selected setting is reset to the default value. Further notes You configure the setting with the command (properties). spanning-tree mst You display these settings and other information with the commands that start with show spanning tree ... SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable automatic discovery of a bridge connected to the interface. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no spanning-tree auto-edge SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The BPDU transmit status has switched over. Further notes You can display the status of this function and other information with the show spanning tree command with the option. interface detail SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
6.3.5.9 spanning-tree bpdufilter Description With this command, you configure the BPDU transmission status for a port. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You delete the configuration of a port as a layer 2 gateway port with the command spanning-tree layer2-gateway-port You can display other information with the command with the show spanning tree interface option. detail SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you enable the function. Requirement ● Spanning tree is enabled. You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable the function. Requirement You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no spanning-tree loop-guard Result The function is disabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The port is prevented from adopting the role of root port. Further notes You cancel the lock with the command. no spanning-tree restricted-role You can display the status of this function and other information with the show spanning tree command. detail SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The port cannot initiate any modifications to the network topology. Requirement You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: spanning-tree restricted-tcn SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you configure the Hello time after which the bridge sends its configuration BPDUs. A change to this value applies to all MST instances active on this interface. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you reset the hello time after which the bridge sends its configuration BPDUs to the default value. The default value is 2 seconds. Requirement You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Keyword for a spanning tree instance instance-id Number of the instance 1 ... 64 priority Keyword for the priority value Value for the priority 0 ... 61440 Default: Priority of the device SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● The MAC address is configured to the MAC address of the device. Requirement You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call up the command with the following parameters: no spanning-tree[mst<instance-id(1-64)>]pseudoRootId SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the MSTP configuration mode with the command, you return to the Global exit configuration mode. ● If you exit the MSTP configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You cancel the assignment of the VLAN to an MST instance with the command. no instance You delete the MST instance with the command. no instance You display this setting and other information with the show spanning-tree mst command. configuration SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The assignment of a VLAN to an MST instance is canceled or the MST instance is deleted. Further notes You delete a VLAN of an MST instance with the command. instance You display this setting and other information with the show spanning-tree mst command. configuration SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The name is configured. Further notes You delete the name of the MST region with the command. no name You display this setting and other information with the show spanning tree mst command. configuration SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The name is reset to the default value. Further notes You configure the name of the MST region with the command. name You display this setting and other information with the show spanning tree mst command. configuration SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The MST region is assigned a revision number. Further notes You delete the revision number with the command. no revision You display this setting and other information with the show spanning tree mst command. configuration SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The revision number of the MST region is reset to the default value. Further notes You assign a revision number to the MST region with the command. revision You display this setting and other information with the show spanning tree mst command. configuration SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli> cli# Syntax Call up the command with the following parameters: show passive-listening Result is displayed if passive listening is disabled. If passive listening is enabled, disabled enabled is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The passive listening function is enabled. Further notes You disable passive listening with the command. no passive-listening You display the status of passive listening with the command. show passive-listening SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The passive listening function is disabled. Further notes You enable passive listening with the command. passive-listening You display the status of passive listening with the command. show passive-listening SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Defines an address range using the subnet mask. /8, /16 or /24 connected Shows the direct connections. ospf Shows the OSPF routes. static Shows the static routes. summary Shows a summary. Result The routing table is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip gateway Result The default gateway is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show dcp server Result The overview of the status of the DCP function and access rights is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Enter a valid interface name For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The overview of the DCP forwarding behavior is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip dns cache SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows DNS statistics. It provides information about the type and number of queries to the DNS server. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Range of values prefix specifies the IP address or the address range enter a valid IP address mask specifies the subnet mask used for enter a valid subnet prefix Use decimal notation. mask SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Use decimal notation. mask next-hop specifies the IP address to which the selected addresses enter a valid IP address were forwarded. distance The value for the administrative distance. 1 ... 255 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: ip routing Result The routing function is enabled. Further notes You disable the function with the command. no ip routing You display the setting with the command. show ip route SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
(ICMP) can be sent to it. These packets of type 8 request the recipient to send a packet back to the sender (echo reply). With this command, you enable the ICMP echo reply messages. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
ICMP echo reply messages are disabled. Further notes You change the setting with the command. ip echo-reply You can display the setting of this function and other information with the show ip command. information SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable the Telnet server. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no telnet-server SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The read and write permissions for the DPC server are configured. The DCP server is enabled. Further notes You disable the DCP server with the command. no dcp server SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command enables the DNS client of the device. To be able to use the function, a DNS server must be reachable. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: ip domain lookup SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: ip name-server ipv4 <ip-address> [index <id1-3>] SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameters have the following meaning: Parameter Description Range of values index Keyword for the index Index of the DNS server 1 ... 3 Result The specified entries for the DNS servers were deleted. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
0 ... 32 length a number of "1" bits secondary Further subnet for this interface For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Specify this parameter if you want to disable the DHCP function explicitly. For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call up the command with the following parameters: dcp forwarding {block|forward} The parameters have the following meaning: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 252
Network protocols 7.1 IPv4 protocol Parameter Description block DCP frames are discarded forward DCP frames are forwarded Default: forward Result The forwarding behavior of the interface for DCP frames is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip dhcp client SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: ip dhcp config-file-request Result The DHCP config file request option is enabled. Further notes You disable the DHCP config file request option with the no ip dhcp config-file-request command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: no ip dhcp config-file-request Result The DHCP config file request option is disabled. Further notes You enable the DHCP config file request option with the ip dhcp config-file-request command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The client registers with the assigned system name pnio-name-of- the client registers with the PNIO name. The name station is assigned with the PST tool. Result The registration mode of the DHCP client is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: show dhcp server Result The IP addresses of the DHCP servers are displayed. Further notes With the " " command, you specify the IP addresses. ip dhcp server SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You display the settings with the command. show ip dhcp relay information 7.3.3.2 no ip dhcp server Description With this command, you delete the IP address of the DHCP server. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The Circuit ID is encoded in the DHCP packet if the "DHCP relay information" option is enabled. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Global Configuration mode or in the Interface Configuration mode of VLAN. The command prompt is as follows: cli(config)# cli(config-if-$$)# Syntax Call the command without parameter assignment: ip dhcp relay information option SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You enable the option with the command. no ip dhcp relay information option You can display the status of this option and other information with the show ip dhcp relay command. information SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
7.3.3.7 no service dhcp-relay Description This command disables the DHCP relay agent. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● The interface is a router port. You are in the Interface Configuration mode of VLAN The command prompt is as follows: cli(config-if-$$)# Syntax Call up the command with the following parameters: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameter assignment: no ip dhcp relay circuit id Result The Circuit ID is removed. Further notes You configure the Circuit ID with the command. ip dhcp relay circuit-id SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You configure the interface as a router port with the command. no switchport You display the IP addresses with the command. show dhcp server You display the settings with the command. show ip dhcp relay information SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows the details of the configured of SNMP communities. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description This command shows the configured SNMP filters. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows the rights of the configured SNMP groups. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you display the configured SNMP notification types. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description This command shows the configured SNMP target parameters. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows the settings for the SNMP user. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable the SNMP agent function. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no snmpagent SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call up the command with the following parameters: snmp agent version{v3only|all} The parameters have the following meaning: Parameter Description v3only only SNMP V3 queries are processed all SNMP queries are processed Default: Result The setting is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
• priv enables authentication and encryption read the data can be read • ReadView Keyword • none write the data can be read and written • WriteView Keyword • none SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 277
You display the access configurations for SNMP groups with the show snmp group access command. You display the configured SNMP tree views with the command. show snmp viewtree SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You display the access configurations for SNMP groups with the show snmp group access command. You display the configured SNMP tree views with the command. show snmp viewtree SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The settings are retained after a restart If optional parameters are not specified when configuring a community, the following defaults apply: Parameter Default values nonvolatile Storage type Result The settings are configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You show the details of an SNMP community with the command. show snmp community You show the status information of the SNMP communication with the command. show snmp SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Parameter Default value nonvolatile Storage type Result The details of the group are configured. Further notes You delete the details of an SNMP group with the command. no snmp group SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You change the details of an SNMP group with the command. snmp group You display the created SNMP groups with the command. show snmp group You display the created SNMP user with the command. show snmp user SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You delete the details of an SNMP group with the command. no snmp notify You display the configured SNMP notifications with the command. show snmp notif You display the configured SNMP target addresses with the show snmp targetaddr command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You change the details of an SNMP group with the command. snmp notify You display the configured SNMP notifications with the command. show snmp notif You display the configured SNMP target addresses with the show snmp targetaddr command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Keyword for the maximum number of attempts to obtain a response to an inform request message RetryCount Number of attempts 1 ... 3 taglist Keyword for • TagIdentifier • none SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
7.4.2.13 no snmp targetaddr Description With this command, you delete the SNMP target address. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameters have the following meaning: Parameter Description Range of values ParamName Name of the SNMP parameter max. 32 characters user Keyword for the user name UserName Value for the user name max. 32 characters SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 288
You configure the user profile with the command. snmp user You configure a filter with the command. snmp filterprofile You display the list of users with the command. show snmp user SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you block write access for SNMP V1 and V2 PDUs. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You block write access for SNMP V1 and V2 PDUs with the command. snmp v1-v2 readonly 7.4.2.18 snmp user Description With this command, you configure the details of an SNMP user. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 291
The details of the SNMP user are configured. Further notes You delete the settings with the command. no snmp user You display the configured users with the command. show snmp user SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● An SNMP group has been created ● The access to the group is configured with snmp access You are in the Global Configuration mode. The command prompt is as follows: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 293
You display the configured view trees with the command. show snmp viewtree You display the SNMP group access rights with the command. show snmp group access You configure the SNMP group access rights with the command. snmp access SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Name of the view max. 32 characters OIDTree Object ID Path information of the MIB tree Result The SNMP view is deleted. Further notes You configure a view with the command. snmp view SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show events sender email SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the EVENTS configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the EVENTS configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
An entry for the SMTP server is configured. Further notes You delete an SMTP server entry with the command. no smtp-server 7.5.4.2 no smtp-server Description With this command, you delete an SMTP server entry. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
7.5.4.3 sender mail-address Description With this command, you configure the e-mail name of the sender. Requirement You are in the EVENTS Configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The e-mail name of the sender is reset. Further notes You configure the e-mail name of the sender with the sender mail-address You display the setting with the command. show events sender email SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you configure an SMTP port. Requirement You are in the EVENTS Configuration mode. The command prompt is as follows: cli(config-events)# Syntax Call up the command with the following parameters: smtp-port <smtp-port(1-65535)> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The SMTP port is reset to the default value. Further notes You configure the setting with the command. smtp-port You display the setting with the command. show smtp-port SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can display the setting of this function and other information with the show ip http command. server status You deactivate HTTP on the device with the command. no ip http SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
HTTP is disabled on the device. Further notes You can display the setting of this function and other information with the show ip http command. server status You enable HTTP with the command. ip http SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip http secure server status Result The status, cipher suite and version of the HTTP secure server is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ssl server-cert Result The SSL server certificate is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the IP ARP table is displayed. Result The IP ARP table is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Slot no. and port no. of the interface Enter a valid interface name Cpu0 The interface is configured as "Out-of-band management interface" For information on addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You generate a static entry in the ARP cache with the command. You can display the status of this function and other information with the show ip command. You configure the router port with the command. no switchport SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can reset the timeout setting to the default with the command. no arp timeout You can display the status of this function and other information with the show ip arp command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The timeout setting for the ARP cache is reset to the default value. Further notes You change the timeout setting with the command. arp timeout You can display the status of this function and other information with the show ip command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: ssh-server As default the function is "enabled". Result The SSH protocol is enabled on the device. Further notes You disable the SSH protocol with the command. no ssh-server SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no ssh-server Result The SSH protocol is disabled on the device. Further notes You enable the SSH protocol with the command. ssh-server SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show forward-all Result The entries of the GMRP forward all table are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you want to enable or disable the function for a specific interface on the device, use the command in the Interface Configuration mode. gmrp You can display the status of this function and other information with the show vlan device command. info SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you want to enable the function for a specific interface on the device, use the gmrp command. You can display the status of this function and other information with the show vlan device command. info SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you want to disable the function for a specific interface on the device, use the no gvrp command. You can display the status of this function and other information with the show vlan device command. info SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you want to enable the function for a specific interface on the device, use the gvrp command. You can display the status of this function and other information with the show vlan device command. info SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The information is displayed. 8.2.2 show ip igmp snooping forwarding-database Description This command shows the Multicast forwarding entries for all or a selected VLAN. Requirement ● IGMP snooping is enabled on the device SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
[Vlan<vlan id>] The parameters have the following meaning: Parameters Description Range of values Vlan Keyword for a VLAN connection vlan id Number of the addressed VLAN 1 ... 4094 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip igmp snooping switch-ip Result The IP address is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable IGMP snooping for all VLANs. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no ip igmp vlan-snooping SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Shows that the number of a VLAN follows vlan id Number of the addressed VLAN 1 ... 4094 If you do not select a VLAN, the counters of all VLANs will be deleted. Result The counters are deleted. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Address of the source Enter a valid IP address For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The IP address is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can reset the setting to the default with the no ip igmp snooping port-purge-interval command. You can display the status of this function and other information with the show ip igmp command. snooping globals SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Further notes You configure the setting with the command. ip igmp snooping port-purge-interval You can display the status of this function and other information with the show ip igmp command. snooping globals SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Further notes You delete the setting with the command. no ip igmp snooping querier You can display the status of this function and other information with the show ip igmp command. snooping SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Further notes You configure the setting with the command. ip igmp snooping querier You can display the status of this function and other information with the show ip igmp command. snooping SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Note Avoiding bad configurations When using the commands in this section, you should take particular care because a bad configuration of this function can have serious negative affects on the network. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you reset the counters of the standby function. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# Syntax Call the command without parameters: clear standby counter Result The counter is reset. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ring-redundancy Result The current Ring redundancy configuration is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: ring-redundancy configuration Result You are now in the Redundancy Configuration mode. The command prompt is as follows: cli(config-red)# Further notes You exit the Redundancy Configuration mode with the command. exit SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
8.4.5.3 no ring-redundancy Description With this command, you disable the ring redundancy function on a device. Requirement You are in the Global Configuration mode. The command prompt is as follows: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The standby function is enabled / disabled. Further notes You disable the setting with the command. no ring-redundancy standby You can display the status of this function and other information with the show ring- command. redundancy SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the Redundancy Configuration mode with the command, you return to the exit Global Configuration mode. ● If you exit the Redundancy Configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Note Differing port addresses The first and second port must be configured on different interfaces Result The ports of the ring redundancy are configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Redundancy Configuration mode. The command prompt is as follows: cli(config-red)# Syntax Call the command without parameters: no standby connection-name Result The name of the standby connection is deleted. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you disable the standby force-master function. Requirement ● HRPis activated You are in the Ring Redundancy Configuration mode. The command prompt is as follows: cli(config-red)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Enter a valid interface name For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The ports for a standby connection are configured and enabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The ports for a standby connection are disabled. Further notes You enable the setting with the command. standby port {<iftype> <ifnum>} You display the status of this function and other information show ring-redundancy SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Redundancy configuration mode. The command prompt is as follows: cli(config-red)# Syntax Call the command without parameters: standby wait-for-partner Result The "Wait for standby partner" function is enabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Redundancy configuration mode. The command prompt is as follows: cli(config-red)# Syntax Call the command without parameters: no standby wait-for-partner Result The "Wait for standby partner" function is disabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Enter a valid interface name For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The unicast blocking settings for ports are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you do not select any parameters from the parameter list, the default value is used. For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The table is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you do not select any parameters from the parameter list, the default value is used. For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The table is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Type or speed of the interface gigabitethernet type extreme-ethernet interface-id Slot no. and port no. of the interface # digit /digit# Slot: 0 ... 6 or 12 Port: 1 ... 4 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 350
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The static unicast function is disabled. Further notes You activate the setting with the command. no mac-address-table static unicast SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If no parameters are specified, the settings for all ports are displayed. Result The multicast blocking settings for ports are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Auto-Hotspot". Result The table is displayed. 8.6.3 show mac-address-table static multicast Description This command shows the MAC addresses of the static multicast configurations. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
(Page 30)". Result The settings for static multicast blocking are configured. Further notes You enable / disable the setting with the no mac-address-table static multicast <mac command. address> <vlan-id(1-4094)> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The settings for static multicast are configured. Further notes You disable the setting with the no mac-address static multicast <mac-address><vlan-id(1- command. 4094)> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you do not select any parameters from the parameter list, the default value is used. For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The static multicast function is disabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● VRRP The layer 3 functions describe the routing properties of the device. These are not normally included in the basic device and if necessary must be enabled or released extra. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Shows the OSPF entries in the routing table. Shows the RIP entries in the routing table. static Shows the static routes in the table. Result The routing table is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show ip protocol Result The current settings of the activated routing protocols are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows the routes that were generated with OSPF. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
= 0 ... 255 0.0.0.0 = backbone area database-summary Number of LSA types per area and the total number of areas self-originate Number of LSAs generated by the local router. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call up the command with the following parameters: show ip ospf [area-id] database asbr-summary|external|network| nssa-external|router|summary [link-state-id] adv-router <ip-address>|self-originate SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows the routes to the area border routers and to the AS boundary routers. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the information is displayed for all available interfaces. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
IP address of the router. detail OSPF information on the neighbor For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the request list is displayed for all neighbors. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the list is displayed for all neighbors. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call up the command with the following parameters: show ip ospf {area-range|summary-address } SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command is available only with layer 3. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: router ospf SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: no router ospf Result Routing with OSPF is disabled. Further notes You enable routing with OSPF with the command. router ospf SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# Syntax Call the command without parameters: ASBR Router Result The autonomous system boundary router is enabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Further notes You enable the autonomous system boundary router with the command. ASBR Router You can display the status of this function and other information with the show ip ospf command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The address range is advertised to the outside. A summary LSA of Type 3 is generated. notadvertise The address range is not advertised to the outside. Result The address range is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
0.0.0.0 = backbone area Network IP address of the address range specify the IP address Mask Subnet mask of the address range specify the subnet mask. summary Summary LSA Type7 LSA type 7 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command is available only with layer 3. Requirement You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# Syntax Call up the command with the following parameters: area <AreaId> range <Network> <Mask> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# Syntax Call up the command with the following parameters: area <area-id> nssa no-summary | default-information-originate SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# Syntax Call up the command with the following parameters: area <area-id> stub [ no-summary ] The parameters have the following meaning: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# Syntax Call up the command with the following parameters: no area <area-id> { stub | nssa } SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config-ospf)# Syntax Call up the command with the following parameters: area <area-id> virtual-link <router-id> [authentication simple |messagedigest| null [hello-interval <value (1-65535)>] [retransmit-interval <value(0-3600)>] [transmit-delay <value (0-3600)>] [dead-interval <value>] SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 380
Keyword for the unencrypted password Password enter the password. Maximum length: characters message-digest-key Keyword for the ID of the password key-id ID of the password. specify the ID 0 ... 255 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config-ospf)# Syntax Call up the command with the following parameters: no area <area-id> virtual-link <router-id> [authentication] [hello-interval] [retransmit-interval] [transmit-delay] [dead-interval authentication-key | message-digest-key <Key-id (0-255)> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 382
Maximum length: characters message-digest-key Keyword for the ID of the password key-id ID of the password. specify the ID 0 ... 255 Result The virtual link is removed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The compatibility with RFC 1583 is enabled. Further notes You disable the compatibility with the command. no compatible rfc1583 You can display the status of this function and other information with the show ip command. ospf SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you enable the function with which a standard route is generated for external routes into the OSPF routing domain. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable the function with which a standard route is generated for external routes into the OSPF routing domain. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you enable the function with which a standard route is always generated for external routes into the OSPF routing domain. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable the function with which a standard route is always generated for external routes into the OSPF routing domain. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
9.3.13.17 network area Description With this command, you specify an OSPF interface and the Area ID connected to the OSPF interface. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you remove the OSPF interface and the Area ID connected to the OSPF interface. Note This command is available only with layer 3. Requirement You are in the OSPF Router configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you configure the information for the route. The routes are further distributed with this information Note This command is available only with layer 3. Requirement You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you delete the information for the new external routes. Note This command is available only with layer 3. Requirement You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# Syntax Call up the command with the following parameters: redistribute {static | connected | rip | default | all} SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# Syntax Call up the command with the following parameters: no redistribute {static | connected | rip | default | all} SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
<name(1-20)> in The parameters have the following meaning: Parameter Description Values name Name of the routing table. Maximum of 20 characters. Incoming routing information is filtered. Result The filtering is enabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you specify the ID of the router. Note This command is available only with layer 3. Requirement You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# Syntax Call up the command with the following parameters: summary-address <Network> <Mask> <AreaId> allowAll | denyAll | advertise |not-advertise SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 397
You delete the address range with the command. no summary-address You can display the status of this function and other information with the show ip ospf - command area-range / summary-address SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This section describes commands that you can call up in the interface configuration mode. Depending on the Interface selected, various command sets are available. In the Global configuration mode, enter the command to change to this mode. interface SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameters have the following meaning: Parameter Description Range of values / note message-digest Authentication using MD5 If you enter the command without parameters, an unencrypted password is used for authentication. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameter assignment: ip ospf authentication Result The type of authentication is reset. Further notes You enable the authentication with the command. ip ospf authentication SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Range of values / note Password Password Enter a password. Maximum length: 8 characters Result The password is specified. Further notes You delete the password with the command. no ip ospf authentication-key SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you specify the costs for the OSPF interface. Note This command is available only with layer 3. Requirement ● The interface is a layer 3 interface. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command is available only with layer 3. Requirement ● The interface is a layer 3 interface. You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call up the command with the following parameters: ip ospf dead-interval <seconds (0-0x7fffffff)> The parameter has the following meaning: Parameter Description Range of values / note seconds 0 ... 0x7fffffff Interval in seconds SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You specify the interval with the command. ip dead-interval You show the configuration of the OSPF interface with the show ip ospf interface command. You configure the router port with the command. no switchport SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The interval is specified. Further notes You delete the interval with the command. no ip hello-interval You show the configuration of the OSPF interface with the show ip ospf interface command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
9.3.14.11 ip ospf message-digest-key Description With this command, you specify the password and the ID for authentication with MD5. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command is available only with layer 3. Requirement ● The interface is a layer 3 interface. You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● The interface is a layer 3 interface. You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call up the command with the following parameters: ip ospf retransmit-interval <seconds (0 - 3600)> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameter assignment: no ip ospf retransmit-interval Result The interval is deleted. Further notes You configure the interval with the command. ip retransmit-interval You configure the router port with the command. no switchport SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you delete the interval. Note This command is available only with layer 3. Requirement ● The interface is a layer 3 interface. You are in the Interface Configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call up the command with the following parameters: ip ospf priority <value (0 - 255)> The parameter has the following meaning: Parameter Description Range of values / note Value Priority 0 ... 255; Default: 100 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The priority is deleted. Further notes You configure the priority with the command. ip ospf priority You display the router ID and other information with the command. show ip ospf interface SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Routing with RIP is enabled. You are now in the Router configuration mode. The command prompt is as follows: cli (config-rip)# Further notes You disable the RIP protocol with the command. no router rip SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the RIPv2 Router configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the RIPv2 Router configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the RIP Router configuration mode. The command prompt is as follows: cli(config-rip)# Syntax Call the command without parameter assignment: no auto-summary Result Subnets are not summarized according to classes. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The value for the administrative distance is set. 9.4.3.4 no distance Description This command resets the administrative distance to the default (120). Requirement You are in the RIP Router configuration mode. The command prompt is as follows: cli(config-rip)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameters have the following meaning: Parameter Description Values name Name of the routing table. Maximum of 20 characters. Incoming routing information is filtered. Outgoing routing information is filtered. Result The filtering is enabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The filtering for outgoing routing information is disabled. Result The filtering is disabled. 9.4.3.7 network Description This command enables the RIP protocol for an IP interface. Requirement You are in the RIP Router configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameter has the following meaning: Parameter Description Values ip-address The IP address for which RIP will be disabled. Specify a valid IP address. Result RIP is disabled for the specified IP interface. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Routes learned by OSPF are distributed. static Static routes are distributed. route-map Keyword for a route map. name Name of the route map. Maximum of 20 characters Result The information forwarded by RIP has been specified. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
No static routes are forwarded. route-map Keyword for a route map. name Name of the route map. Maximum of 20 characters Result In certain cases, forwarding of routing information is disabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The updating of route information is according to RIPv1 or RIPv2 (default for this parameter) Requirement You are in the RIP Router configuration mode. The command prompt is as follows: cli(config-rip)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call up the command with the following parameters: output-delay <milli-seconds(8-50)> The parameter has the following meaning: Parameter Description Values milli-seconds Delay in milliseconds. 8 ... 50 Result RIP updates are forwarded only after the set delay. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
%% is a short name for the interface type and $$$ is the numbering of the interface. Syntax Call up the command with the following parameters: ip rip default route originate <metric(1-15)> The parameter has the following meaning: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command specifies the RIP version for incoming routing information. Requirement You are in the VLAN configuration mode of the VLAN interface with the ID $$$ or in the configuration mode for a router port. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config-if-vlan-$$$)# cli(config-if-RPort-%%$$$)# where %% is a short name for the interface type and $$$ is the numbering of the interface. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Only RIPv1 updates are sent. Only RIPv2 updates are sent. RIPv1 and RIPv2 updates are sent. none No RIP updates are sent. Result It has been specified which RIP version outgoing updates need to have. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
%% is a short name for the interface type and $$$ is the numbering of the interface. Syntax Call the command without parameters: no ip rip send version Result All RIP updates are sent. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Parameters Description Range of values vlan Keyword for a VLAN connection VlanId Number of the addressed VLAN 1 ... 4094 interface-type Type or speed of the interface • gigabitethernet • extreme-ethernet SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call up the command with the following parameters: show vrrp interface vlan <VlanId(1-4094)>| <interface-type><interface-id> <VrId(1-255)> brief|detail |statistics SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Privileged EXEC mode again. 9.5.3.1 router vrrp Description With this command, you enable routing with VRRP and change to the VRRP Router Configuration mode. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command is available only with layer 3. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: no router vrrp SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command is available only with layer 3. Requirement You are in the VRRP Router Configuration mode. The command prompt is as follows: cli(config-vrrp)# Syntax Call up the command with the following parameters: interface{vlan<vlan-id(1-4094) <interface-type><interface-id>} SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you delete a VRRP interface. Note This command is available only with layer 3. Requirement You are in the VRRP Router Configuration mode. The command prompt is as follows: cli(config-vrrp)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement ● The Router Configuration mode is activated. You are in the Router vrrp Configuration mode. The command prompt is as follows: cli(config-vrrp)# Syntax Call the command without parameters: vrrp virtual-ping SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The function for pings to virtual addresses is disabled. Further notes You enable the setting with the command. vrrp virtual-ping You can display the status of this function and other information in Exec mode with the show command. vrrp SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameters have the following meaning: Parameter Description Range of values vrid ID of the virtual router 1 ... 255 ip_addr Value for an IP address specify a valid IP address SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Range of values vrid ID of the virtual router 1 ... 255 ip_addr Value for an IP address specify a valid IP address Result The IP address is removed from the virtual router. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
All IP addresses of the group are removed. Further notes You configure a VRRP interface with the command. interface You display the IP addresses with the command. show vrrp interface - vrid SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You disable the function with the command. no vrrp preempt You can display the status of the function with the or with the show vrrp interface - vrid command. show vrrp interface SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You enable the function with the command. vrrp preempt You can display the status of the function with the or with the show vrrp interface - vrid command. show vrrp interface SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You configure a VRRP interface with the command. interface You remove the primary IP address with the command. no vrrp pirmary-ip You show the configuration of the virtual router with the show vrrp interface - vrid command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You configure a VRRP interface with the command. interface You assign IP addresses to a virtual router with the command. vrrp associated-ip You display the IP addresses with the command. show vrrp interface - vrid SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You remove the priority with the command. no vrrp priority You assign IP addresses to a virtual router with the command. vrrp associated-ip You display the priority with the command. show vrrp interface - vrid SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You configure a VRRP interface with the command. interface You create the priority with the command. vrrp priority You assign IP addresses to a virtual router with the command. vrrp associated-ip SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You configure a VRRP interface with the command. interface You disable the authentication with the command. no vrrp text-authentication You assign IP addresses to a virtual router with the command. vrrp associated-ip SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You configure a VRRP interface with the command. interface You enable the authentication with the command. vrrp text-authentication You assign IP addresses to a virtual router with the command. vrrp associated-ip SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You remove the interval with the command. no vrrp timer You assign IP addresses to a virtual router with the command. vrrp associated-ip You show the interval with the command. show vrrp interface - vrid SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You configure the interval with the command. vrrp timer You assign IP addresses to a virtual router with the command. vrrp ipv4 You show the interval with the command. show vrrp interface - vrid SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Load control This part contains the sections describing the functions for controlling and balancing network load. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameter from the parameter list, the entries are displayed for all available interfaces. Result The entries are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
1 ... 80000000 Default: The packet rate is set to The outgoing data stream is not limited. If you do not select any parameters from the parameter list, the default value is used. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This function is known as storm control. With this command, you enable the storm control function for broadcast, multicast or unknown unicast packets of an interface. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 457
The packets are sent without any delay even when there is high network load. To have the sending of the packets delayed when necessary, configure the threshold value with the command. storm-control level Result The storm control function is enabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The storm control function is disabled. Further notes You enable the function with the command. storm-control SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The value for the storm control function is configured. Further notes You can reset the setting to the default with the command. no storm-control level SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The value for the storm control function is reset to the default. Further notes You configure the value for the storm control function with the storm-control level command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Number of the addressed VLAN 1 ... 4094 For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The static multicast MAC address is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Specifies the name of a port channel forbidden- Keyword for the interface description of the blocked ports ports For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Number of the addressed VLAN 1 ... 4094 For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The entry is deleted. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Enter a valid interface name port-channel Specifies the name of a port channel a,b,c-d For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The entry is deleted. Further notes With the command, you display the list of show mac-address-table static unicast configured entries. With the command, you create an entry. mac-address-table static unicast SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Further notes You disable the filter with the command. no switchport ingress-filter You can display the status of the ingress filter and other settings with the show vlan port command. config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The ingress filter is deactivated. Further notes You enable the filter with the command. switchport ingress-filter You can display the status of the ingress filter and other settings with the show vlan port command. config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows whether or not MAC aging is enabled. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call up the command with the following parameters: mac-address-table aging-time <seconds(10-630)> The parameter has the following meaning: Parameter Description Range of values seconds Life of the entry in seconds 10 ... 630 Default: 40 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you enable the "Aging" function. The "Aging" function ensures that an entry in the MAC address list that was learned dynamically is deleted again after a certain time. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no mac-address-table aging Result The "Aging" function is disabled. Further notes You enable the "Aging" function with the command. mac-address-table aging SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
(Page 30)". If you do not select any parameters from the parameter list, the information for the router will be displayed. Result The settings of the flow control function are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameters have the following meaning: Parameters Description Enables the function Disables the function Result The settings are configured. Further notes You can display the status of this function with the command. show flow-control SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows assignment table for DSCP. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: Result You are now in the QOS configuration mode. The command prompt is as follows: cli(config-qos)# Further notes You exit the QOS configuration modewith the command exit SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Queue that it is assigned to this service class 1 … 8 Default: 2 For the following default service classes, the rule applies accordingly. Result The assignment table for service classes is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● The DSCP codes 0 to 7 are assigned to queue 1. ● The DSCP codes 8 to 15 are assigned to queue 2. The rules apply accordingly to the DSCP codes following. Result The assignment table for DSCP codes is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Security and authentication This part contains the sections that describe the access rights and authentication methods. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
This command shows the logged-in CLI users. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# Syntax Call the command without parameters: show users Result The logged-in CLI users are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: whoami Result The user name of the logged in user is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The connection statistics are displayed. 11.2.2 show radius server Description This command shows the RADIUS server configuration. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: radius-server {ipv4 <ip address> | fqdn-name <FQDN(100)>} [auth-port <number(1- 65535)>] [retransmit <rtm(1-254)>][key<secret-key-string>][primary] SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
11.2.3.2 no radius-server Description With this command, you delete a RADIUS server entry on the RADIUS client. Requirement You are in the Global configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 485
You show the configuration of a RADIUS server on the client with the show radius server command. You show the statistical information of this function with the show radius statistics command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you do not select any parameters from the parameter list, the configuration of all access control lists will be displayed. Result The configuration of the access control lists is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You delete the MAC access control list with the command. no mac access-list extended You exit the MAC ACL configuration mode with the command. exit You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the Interface configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The packets are filtered according to the access control list (ACL). Further notes You disable the setting with the command. no mac access-group You display the statistical data of the access control list with the show access-lists command. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the MAC ACL configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the MAC ACL configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
MAC address of the permitted outgoing connection Enter a valid MAC address For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The index number of the access control list is not used for this. Requirement You are in the MAC ACL Configuration mode. The command prompt is as follows: cli(config-ext-macl)# Syntax Call up the command with the following parameters: deny {any|host<src-mac-address>}{any|host<dest-mac-address>} SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 494
You exit the MAC ACL Configuration mode with the command. exit You delete the MAC access control list with the command. no mac access-list extended You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameters have the following meaning: Parameter Description Range of values standard Specifies that a standard access control list is generated access-list-number Number of the standard access control list 1 ... 1000 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The access control list is deleted. Further notes You generate an IP access control list with the command. ip access-list You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The parameters have the following meaning: Parameters Description Values access-list-number Number of the access control list 1 ... 65535 Specifies that incoming packets are filtered Specifies that outgoing packets are filtered SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
1 ... 65535 Specifies that incoming packets are filtered Specifies that outgoing packets are filtered If you do not specify a number of for an access control list, all lists are deleted. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● Incoming and/or outgoing frames of a specific host are forwarded. ● Incoming and/or outgoing frames of hosts of a specific subnet are forwarded. ● Incoming and/or outgoing frames of a specific protocol are forwarded. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 500
Keyword for a 32 bit long subnet mask. dest-ip Destination IP address Enter a valid IP address. network-dest-ip Network destination address Enter a valid combination of IP address and subnet mask. mask Corresponding subnet mask SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Processing order of the lists The access control lists are processed on the interface in the order in which they were created. The index number of the access control list is not used for this. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 502
Corresponding subnet mask value Value 0 ... 63 dscp Keyword for the Differentiated Services Codepoint value Value for the Differentiated Services Codepoint 0 ... 63 Result The IP access list has been configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The access control lists are processed on the interface in the order in which they were created. The index number of the access control list is not used for this. Requirement You are in the ACL standard configuration mode. The command prompt is as follows: cli(config-std-nacl)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 504
Further notes You delete an IP access control list with the no ip access-list standard <acl-num> command. You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Blocks all outgoing frames host Keyword for a 32 bit long subnet mask. dest-ip Destination IP address enter a valid IP address. network-dest-ip Network destination address enter a valid combination of SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● Incoming and/or outgoing TCP segments of a specific host are forwarded. ● Incoming and/or outgoing TCP segments of hosts of a specific subnet are forwarded. ● Incoming and/or outgoing TCP segments are forwarded to specific ports. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 507
Forwards all outgoing TCP segments. host Keyword for a 32 bit long subnet mask. dest-ip Destination IP address enter a valid IP address. network-dest-ip Network destination address enter a valid combination of SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● Incoming and/or outgoing TCP segments of a specific host are not forwarded. ● Incoming and/or outgoing TCP segments of hosts of a specific subnet are not forwarded. ● Incoming and/or outgoing TCP segments are not forwarded to specific ports. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 509
Blocks all outgoing TCP segments host Keyword for a 32 bit long subnet mask. dest-ip Destination IP address enter a valid IP address. network-dest-ip Network destination address enter a valid combination of SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Processing order of the lists The access control lists are processed on the interface in the order in which they were created. The index number of the access control list is not used for this. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 511
Corresponding subnet mask dscp Keyword for the Differentiated Services Codepoint value Value for the Differentiated Services Codepoint 0 ... 63 Result The IP access list for UDP datagrams has been configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Syntax Call up the command with the following parameters: deny udp {any | host <src-ip> | <network-src-ip> <mask>} [{ gt <port-number(1-65535)> | lt <port-number(1-65535)> | eq <port-number(1-65535)> | range <port-number (1- SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 513
Further notes You delete the IP access control list with the no ip access-list standard <acl-num> command. You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
(Page 30)". If you do not select an interface, the configuration of all interfaces is displayed. Result The configuration of the interface for the learning of MAC entries is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The static unicast MAC address entries are deleted from the MAC address table. 11.5.2.2 auto-learn Description With this command, you change to the AUTOLEARN mode. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you block the learning of MAC entries. Only the static address entries of the MAC address list are used on the port. Requirement You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Syntax Call the command without parameters: no switchport lock Result The learning of MAC addresses is enabled. Further notes You block the learning of MAC addresses with the command. switchport lock SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The learned MAC addresses are entered in the port database with the aging time 0 (the entries are NOT deleted when the mac address aging time expires). Further notes You stop automatic learning with the command. stop SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Syntax Call the command without parameters: stop Result Automatic learning is stopped and all learned entries are converted to static entries. Further notes You start automatic learning with the command. start SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Enter a valid IP address For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The information about the configuration of the authorized managers is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: authorized-manager Result The function is enabled. Further notes You disable the function with the command. no authorized-manager SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: authorized-manager ip-source <ip-address> [{<subnet-mask>|/<prefixlength(1-32)>}] [interface[<interface-type<0/a-b,0/c,...>] SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 523
As soon as the list contains an entry and the "authorized-manager" command is executed, access to the system is blocked for all others. You should therefore configure the interface via which you access the system first because your access is otherwise blocked. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Decimal representation of the mask as a number of 1 ... 32 "1" bits For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 525
You configure the interfaces and protocols via which an authorized manager is allowed to access the device with the command. authorized-manager ip-source You show the information about the configuration of the authorized managers with the show command. authorized-manager SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Slot no. and port no. of the interface Enter a valid interface name For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The dot1x information is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show dot1x mac-auth mac-info Result A list of the MAC addresses is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Interface configuration dot1x guest-vlan mode. You disable the function with the command no dot1x guest-vlan 11.7.4.2 no dot1x guest-vlan Description With this command, you disable the guest VLAN function for the device. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You also still need to enable MAC authentication for every port intended to use this function. You do this with the command in the Interface configuration mode. dot1x mac-auth You disable the function with the command no dot1x mac-auth SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Privileged EXEC mode. 11.7.5.1 dot1x guest-vlan Description With this command, you enable the guest VLAN function for a port. Requirement You are in the Interface configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no dot1x guest-vlan Result The guest VLAN function is disabled for the device. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, the guest VLAN ID is reset to the default value 1. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no dot1x guest-vlan vlan-id SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you specify how many end devices are allowed to be connected to the port at the same time. Requirement You are in the Interface configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You also still need to enable MAC authentication for the device. You do this with the dot1x command in the Global configuration mode. mac-auth You disable the function with the command no dot1x mac-auth SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you reset MAC authentication for a port. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call up the command with the following parameters: dot1x mac-auth port [mac <aa:aa:aa:aa:aa:aa>] reset SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command you disable the assignment of the VLAN ID for a MAC address by the RADIUS server. Requirement You are in the Interface configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Default: enabled force-authorized force- data traffic via the interface is blocked unauthorized The default value of the function is " ". force-authorized Result The port control parameter is configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
11.7.5.14 set dot1x mac-auth mac-addr count Description With this command, you specify how many end devices are allowed to be connected to the port at the same time. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: dot1x reauthentication Result Periodic authentication is enabled for all interfaces. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Periodic authentication is disabled. Further notes You enable the function with the command. dot1x reauthentication You can display the status of this function and other information with the show command. dot1x SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Mirroring of ports to analyze the data stream without disturbing operation ● Loop detection Detection and elimination of damaging loops. Loops in the network can cause total failure of the transfer and must be detected and eliminated. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you disable the logging of inputs and outputs to the console. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show events config Result The current configuration of the events display is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● Monitoring of the network connections for a change in the connection status Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show events faults status Result A table with the status messages of the error monitoring functions is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show logbook Call up the command with the following parameters: show logbook { info | warning | critical } SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The content of the logbook is deleted. 12.1.10 show cabletest interface Description You can display the status of this function and other information with the show cabletest command. interface SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Addresses and interface names (Page 30) 12.1.11 show interface transceiver details Description This command runs error diagnostics for an SFP port. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show power-line-state Result The status of the power supply is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: events Result You are now in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# Further notes You exit the EVENTS configuration mode with the command exit SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you do not select any parameters from the parameter list, the default value is used. For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result Following the test phase, the result is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
<log entry> The parameter has the following meaning: Parameters Description Note log entry Entry in the logbook max. 150 characters Result The entry has been made in the logbook. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The function of the client selected for the transfer is enabled. Further notes You display the status of the events and the clients with the command. show events config You disable a client with the command. no client config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The client selected for the transfer is disabled. Further notes You display the status of the events and the clients with the command. show events config You enable the function with the command. client config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the EVENTS Configuration mode. The command prompt is as follows: cli(config-events)# Syntax Call up the command with the following parameters: event config {cold-warmstart|linkchange|authentication-failure| rmon-alarm|power-change|rm-state-change|standby-state-change|faultstate-change| stp-change|vrrp-state-change|loopd-state-change|ospf-state-change|all} {logtable|syslog|email|trap|faults|all} The parameters have the following meaning: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 556
With each command call, you can only select one message type and one client. If you want to process several message types or clients, it may be more efficient to first select the option and then disable individual elements. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Client that sends the e-mails trap Client that sends the SNMP traps faults Error LED lights up. The setting is possible only for a cold or warm restart. All clients at once SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Message level warning critical Message level critical If you do not select any parameters from the parameter list, the default value is used. Result The settings of the event grouping are configured. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The settings of the EVENTS grouping are disabled. Further notes You enable the setting with the command. eventgroup You can display the status of this function and other information with the show events configcommand. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The settings are configured. The severity function is enabled. Further notes You disable the setting with the command. no severity You display the status of this function and other information show events config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The settings for sending event messages are configured. Further notes You enable the setting with the command. severity You display the status of this function and other information show events config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You disable the function with the command. no power 12.1.14.11 no power Description With this command, you disable the monitoring of the power supplies. Requirement You are in the EVENTS configuration mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the EVENTS Configuration mode. The command prompt is as follows: cli(config-events)# Syntax Call up the command with the following parameters: The parameters have the following meaning: link {up|down}[{<ifXtype><iface_list>}] SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement You are in the EVENTS Configuration mode. The command prompt is as follows: cli(config-events)# Syntax Call up the command with the following parameters: no {up|down}[{<ifXtype><iface_list>}] SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the EVENTS configuration mode. The command prompt is as follows: cli (config-events) # Syntax Call up the command with the following parameters: syslogserver {ipv4 <ip address> | fqdn-name <FQDN(100)>} [<port(1-65535)>] SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
12.1.14.15 no syslogserver Description With this command, you configure the Syslog server address. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli (config-events) # SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 567
The settings for the Syslog server are disabled. Further notes You enable the setting with the command. syslogserver You can display the status of this function and other information with the show events command. config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
● If you exit the EVENTS configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the EVENTS configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The settings for the Syslog server are configured. The Syslog server was entered in the table Further notes You delete the entry with the command. no syslogserver You can display the status of this function and other information with the show events command. config SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Information Base (MIB) can be monitored for violation of limit values and to store or forward these events in the following ways: ● Entry in the local log ● Sending as SNMP trap SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you can display several parameters with one call. If you do not select any parameters from the parameter list, only the status enabled disabled is shown. Result The settings of the remote monitoring function are displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
1 ... 65535 time absolute The current absolute value of the monitored MIB is evaluated delta The difference between the current and the previous value of the monitored MIB is evaluated SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 573
The alarm for monitoring a MIB variable is configured. Further notes You delete an alarm with the command. no rmon alarm You display the list of configured RMON alarms with the command. show rmon alarms SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You specify its name and the owner and whether or not a logbook entry is made or an SNMP trap is generated. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you delete an entry from the RMON event table. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: no rmon event <index (1-52)> SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Disables the remote monitoring function Default: disabled Result The remote monitoring function is enabled or disabled. Further notes You can display the status of this function and other information with the show command. rmon SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
User name of the user max. 127 characters Result The recording of statistical data is started. Further notes You can display the content of a recording with the command. show rmon statistics SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you configure the collection of statistical data of the interface in a selectable number of recording intervals ("Buckets ") with a specified period. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you end the recording of statistical data of the interface. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 580
Call up the command with the following parameters: no rmon collection history <index(1-52)> The parameter has the following meaning: Parameters Description Range of values index Number of the recording 1 ... 52 Result The data recording is ended. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show monitor status Result The status of the port mirroring function is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you enable the port mirroring function. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: monitor As default the function is "disabled". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Result The port mirroring function is disabled. Further notes You can display the status of this function with the command. show monitor You enable the function with the command. monitor SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Communication via the monitor port is disabled. Further notes You enable the communication with the command. no monitor barrier enabled You display the configuration settings with the command. show monitor barrier SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you configure the destination for mirroring a port. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: monitor session <session-id(1)> destination {interface <interface-type><interface-id>} SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you delete the destination for mirroring a port. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you configure the source for mirroring a port or a VLAN. Requirement ● You are in the Global Configuration mode. ● Monitoring is enabled The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 589
You delete the source for mirroring a port with the command. no monitor session ... source You end and delete a session with the command. no monitor session You display the configuration settings with the command. show monitor session SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". If you do not select any parameters from the parameter list, the default value (both) is used. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The monitor session is deleted. Further notes You display the configuration settings with the command. show monitor session You configure and start mirroring of a port with the command. monitor session SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show loopd For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
If you do not select any parameters from the parameter list, the default value is used. For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The loop interface is displayed. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The loop detection function is enabled Further notes You disable the function with the command. no loopd You can display the status of this function and other information with the show loopdcommand. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Description With this command, you enable the loop detection function for VLAN. Requirement ● Loopd is activated You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
The loop detection function is disabled for VLAN. Further notes You enable the function with the command. loopd vlan mode You can display the status of this function and other information with the "show loopd" command SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Call the command without parameters: loopd port reset For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result The port reset function is enabled. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
You can display the status of this function and other information with the show loopdcommand. 12.5.4.4 loopd reaction local Description With this command, you activate "disable" for loopd reaction local. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
With this command, you enable "no action" for loopd reaction local. Requirement ● Loop detection is enabled. You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no loopd reaction local SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
For information on names of addresses and interfaces, refer to the section "Addresses and interface names (Page 30)". Result "disable" is activated for the loopd reaction remote function. "disable" is the default after enabling loop detection. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
"disable" is the default after enabling loop detection. Further notes You enable the "disable" setting with the command. loopd reaction remote You can display the status of this function and other information with the show loopdcommand. SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 604
259 no ip dhcp server, 259 loadsave, 83 ip domain lookup, 246 lock, 54 no ip domain lookup, 247 logout, 55 ip echo-reply, 242 no ip echo-reply, 243 ip http, 303 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 605
578 no ntp server, 126 no rmon collection history, 579 ntp time diff, 127 rmon collection stats, 577 no rmon collection stats, 578 rmon event, 574 no rmon event, 575 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 606
80 show events faults config, 544 show lock port, 514 show events faults status, 545 show logbook, 546 show events sender email, 295 show mac-address-table, 138 show events severity, 544 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 607
134 show spanning-tree mst, 184 no sntp unicast-server, 135 show spanning-tree mst configuration, 190 spanning-tree, 193 show spanning-tree mst interface, 190 no spanning-tree, 194 show spanning-tree root, 189 spanning-tree (properties), 205 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...
Page 608
398 no vrrp associated-ip, 440 switchport, 74 vrrp group shutdown, 441 no switchport, 75 vrrp ipv4 switchport acceptable-frame-type, 159 no vrrp ipv4, 445 no switchport acceptable-frame-type, 160 vrrp preempt, 442 SCALANCE XM-400/XR-500 Command Line Interface Configuration Manual, 05/2014, C79000-G8976-C252-07...