Honda Prelude 1993 Service Manual page 29

Standards and Service Limits
Conditioning
Section 22
. Wh* u"ing I new belt, adjust dellection or tension to now values. Run tho engine lor 5 minutes thsn turn it o{f
R€Ediust d€flgction or tension to used belt values
Section 23
* When usang a new belt, adjust detlection or tonsion to new valuos. Run the engine lor 5 minutes then turn it ofl.
Re€djust detloction or tension to used bolt and values.
il
ii
:1
! I
I
Air
MEASUREMENT
STANDARD {NEW)
Air conditioning
system
Lubricant capacity
Condenser
cc (ll oz)
Evaporator
Line or hose
R€servoir
1 0 ( 1 / 3 )
3 0 ( 1 )
1 0 { r / 3 )
1 0 ( 1 / 3 )
Compressor
Lubricant capacity cc {tl oz}
Field coil resistance Et 68oF {2OoC) 0
Pulley-to-pressure plate clearance
1 3 0 - 1 5 0 ( 4 1 / 3 - 5 )
3.05-3.35
0.35-0.65 (0.014-0.026)
Comprgasor
belt'
Dollection with lOO N (10 kg, 22 lbs)
between pulleys
10.0-12.0 {0.39-0.471 with used belt
4.5-7.0 {0.18-O.28} with new b€lt
Belt tsnsion N (kg. lbs)
M€asured with belt tension gauge
450-600 (45-60, 99-132) with used bslt
950'1.150 (95'115, 209-254) with new bslt
Electlical -
MEASUREMENT
STAI{DARD INEW)
lgnition coil
Rated voltage V
Primary winding resistanc€ 8t 68 oF (2OoC) o
S€coodarv winding resistance at 68 oF (20ocl kO
1 2
0.6-0.8
Spark Plug
Type
Gap
S6e Sgction 23
1 . 0 - 1 . 1 { 0 . 3 9 - 0 . 4 3 )
lgnition timing
At idling
o BTOC
STDC
1 5 o l 2 o { R e d )
Alternator belt'
Defloction with 1OO N (10 kg, 22 lbs)
between pulleys
10.5-1 2.5 (0.42-0.51 ) with used belt
8.O- 10.0 {0.32-O.4Ol with new b€lt
Belt tension N (kg, lbsl
Mgasured with belt t€nsion gauge
3OO-45O {30-45, 66-99} with usod belt
550-750 {55-75, 121-165) with new belt
MEASUREMENT
STANDARD {NEW)
SERVICE LIMIT
Alternator
(NIPPONDENSO
Output 13.5 V at hot A
Coil r€sistance (rotor) O
SIip ring O.D.
Erush l€ngth
Brush spring t€nsion
g {oz)
80/90
2 . 7 - 3 . 1
1 4 . 2 - 1 4 . 4 { 0 . 5 6 - 0 . 5 7 }
1 0 . 5 ( O . 4 1 )
300-360 t10.6-12.7)
t r.e to.sot
1 . 5 t 0 . 0 6 )
Starter motor
(MITSUBA
1 . 4 k W )
Tvpo
Mica depth
Commutator runout
Commutator O,O.
Brush length
Brush spring t6naion (new)
N (kg, lbsl
Spar gear reduction, Permanent
0.4-0.5 (0.016-0.o20)
o-0.02 {o-0.ooo8)
2 8 . 0 - 2 8 . 1 ( 1 . 1 0 2 , 1 . 1 0 6 )
1 5.8-16.2 (0.62-O.64t
1 6 . 0 , 1 8 . 0 ( 1 . 6 0 - 1 . 8 0 ,
3 . 5 3 - 3 . 9 3 )
magn€t
0.1 5 t0.oo6)
o.o5 (0.oo2)
2 7 . 5 ( 1 . 0 8 3 )
10.0 (0.39)
Starter motor
(MITSUBA
1 . 6 k W )
Tvpe
Mic8 depth
Commutator runout
Commutator O.D.
Brush length
Brush spring tension ln€w)
N lkg, lbs)
Spar gear reduction, Permanent
0.4-0.5 (o.0'16-0.o20l
o-o.02 {o-o.ooo8)
2 8 . 0 - 2 8 . 1 ( 1 . 1 0 2 - 1 . 1 0 6 )
1 5 . 8 - 1 6 . 2 ( 0 . 6 2 - 0 . 6 4 )
1 6 . 0 - 1 8 . O ( 1 . 6 0 - 1 . 8 0 ,
3.53-3.93)
magnet
0 . 1 5 ( 0 . 0 0 6 )
0.o5 t0.o02)
2 7 . 5 { 1 . 0 8 3 )
10.0 (0.39)