Honda Prelude 1993 Service Manual page 27

I
F
Standards and Service Limits
Differential (Manual transmission)
Section
1 5
Differential (Automatic tlansmission)
Section
1 5
Ste6ring
Section 1 7
t
! i
l i
i
!
MEASUREMENT STANDARD INEW} I
SERVICE LIMIT
Final driven
geal
Backlash
0.085-o. 1 42 {O.OO33-0.0056)
o.20 (o.o08l
Dillerontial
carriet
Pinion shaft contact area l.D.
Carrier-to-pinion clearance
Driveshatt contact aroa LD.
Carrisr-to-driveshaft clearance
Right
Left
'1 8.000,1 8.01 8 {0.7087-0.7094}
0.01 3-0.047 (0.0005-o.oo1 9l
28.005-28.025 {' 1. 1026-1.10331
0.025-o.066 (0.001 0-o.oo26l
0.o55-0.091 {o.oo22-o.oo36l
0.10 {o.oo4t
0 . 1 2 t o . o o s t
0.1 5 (0.006I
Dillerential
Backlash
t . D .
Pinion gearto-pinion shaft claarance
o.05-0.'t 5 to.o02-0.0061
18.042-18.066 tO.7103-0.71
' l 3)
0.055-o.095 (0.oo22-o.0037)
AdjLrst with a shim
o.15 {0.006)
Taper roller
bearing preload
Starting Torque N.m {kg-cm, lb-in)
1.4-2.6 ( 4-26, 12-231
Adjust with a shim
MEASUREMENT
STANDARO (NEW}
SERVICE LIMIT
Final driv€n g€ar
Escklash
o.o85-o. 1 42 {O.0033-0.0056)
0.20 (o.oo8)
Dlflerential
carnef
Pinion shaft contact area l.D.
Caftier-to-pinion clearance
Driveshaft contact area l.D.
CarrieFto-driveahaft clearanace
1 8.000-1 8.01 8 t0.7087-0.7094)
o.o17 -o.o47 {0.0007-0.oo1 9}
2 8 . 0 O 5 - 2 8 . 0 2 5
{ 1 . 1 0 2 6 - 1 . 1 0 3 3 )
0.025-0.066 to.oo1 0-o.oo26)
0 . 1 0 ( 0 . 0 0 4 )
o . 1 2 ( 0 . 0 0 5 )
Differcntial Backlash
L O .
Pinion gear-to-pinion shaft clearance
0.05,0. 1 5 (o.oo2-o.oo6t
1 8.042,18.066
(O.7103-0.71
1 3)
0.059-o.o95 (o.oo23-o.oo37)
Adjust with a shim
o.12 (O.OO5)
Taper roller
bearim preload
Starting Torque New bearing
N.m lkg.cm, lb-inl Reused bearing
2.A-4.O QA-40, 24-3sl
2.5-3.7 t25-37 , 22-321
Adjust with I thim
MEASUREMEl{T
STAI{DARD INEW}
St€sring whsel
Play at steering wheel circumterence
Starting load at stoering wheel circuml€ronce N {kg, lbsl
Engine running
When the hydraulic system to the power steerang
soeed sensor is cut ofl
o-10 (o-o.4)
30 {3.O, 6.61
50 (5.0, 1 1.Ol
Gearbox
Angle ot rack-guide-screw loosengd trom locked position
Pump
Pump pressure with valve closed (oil temp./spoed: 1O5"F
{4OoCl min./idle. Do not run for more than 5 s€conds}.
kPa {kg/cm2, psi}
7.O00-8,OOO
(70-80, 995-1, 1 38t
Power steering
lluid
Recommend€d fluid
Fluid capacity System
, (US qt. lmp qt)
Reservoir
Honda power steoring fluid-V
1 . 7 { 1 . 8 0 , 1 . 5 0 1
0.5 {o.53, 0.441
Power st€gring
belt'
Deflection with
'lOO N (1o kg, 22 lbs) between pulleys
13.5-16.5 10.53-0.65) with used belt
9.5-1 1,5 {0.37-0.451 with new belt
Belt tension N (kg, lbsl
Mgasured with belt tension gauge
350-5OO {35-50. 77-1101 with used bslt
7OO-9OO (7O-9O, 154-198) with new b€lt
* When using a nsw belt, adjust deflection or tension to new values. Run the engine for 5 minutes then turn it off.
Readiust deflsction or tension to used belt values.