Canon ImageRunner 600 Service Manual page 17

A. Adjusting Images ................. 13-7
1. Adjusting the Image Position
....................................... 13-7
2. Adjusting the Left/Right Image
Margin ............................ 13-8
3. Adjusting the Image Leading
Edge Margin ................. 13-12
4. Adjusting the Left/Right Non-
Image Width ................. 13-12
5. Adjusting the Image Leading
..................................... 13-13
B. Scanner System ................ 13-14
1. Replacing the Scanner Drive
Cable ............................ 13-14
2. Adjusting the Scanner Mirror
Mount ........................... 13-14
3. After Replacing the Scanning
Lamp ............................ 13-14
C. Image Formation System .. 13-15
1. Routing the Primary Charging
Assembly Grid Wire ...... 13-15
2. Routing the Charging
Assembly Charging Wires
..................................... 13-15
3. Mounting the Drum Cleaning
Blade ............................ 13-15
4. Mounting the Developing
Blade ............................ 13-15
5. Replacing the Potential
Sensor/Potential Control PCB
..................................... 13-15
D. Pickup/Feeding System ..... 13-18
1. Orienting the Deck/Cassette
Pickup Roller ................ 13-18
2. Orienting the Deck/Cassette
Separation Roller .......... 13-19
3. Orienting the Deck/Cassette
Pickup Assembly Feeding
Roller ............................ 13-19
4. Orienting the Manual Feed
Tray/Side Paper Deck Pickup
Roller ............................ 13-20
5. Orienting the Manual Feed
Pickup Roller ................ 13-21
6. Orienting the Side Paper Deck
Feeding Roller .............. 13-21
7. Adjusting the Pressure of the
Deck/Cassette Separation
Roller ............................ 13-22
8. Adjusting the Pressure of the
Manual Tray Pickup/Feeding
Roller ............................ 13-23
9. Mounting the Solenoids
..................................... 13-24
9-1. Position of the Fixing Inlet
COPYRIGHT © 2000 CANON INC. CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.
Guide Solenoid (SL1) ... 13-25
9-2. Position of the Fixing Cleaning
Belt Solenoid (SL2) ...... 13-26
9-3. Position of the Delivery
Flapper Solenoid (SL3)
..................................... 13-27
9-4. Position of the Fixing/Feeding
Unit Locking Solenoid (SL4)
..................................... 13-27
9-5. Position of the Multifeeder
Pickup Latching Solenoid
(SL6)............................. 13-28
9-6. Position of the Deck (right)
Pickup Solenoid (SL7) .. 13-29
9-7. Position of the Deck (left)
Pickup Solenoid (SL8) .. 13-30
9-8. Position of the Cassette 3/4
Pickup Solenoid (SL9/10)
..................................... 13-31
9-9. Position of the Side Paper
Deck Pickup Roller Releasing
Solenoid ....................... 13-32
10. Routing the Manual Feed Tray
Assembly Side Guide Timing
Belt ............................... 13-32
11. Routing the Drive Belt .. 13-33
E. Fixing System .................... 13-34
1. Point to Note When Mounting
the Fixing Heater .......... 13-34
2. Position of the Fixing
Assembly Inlet Guide ... 13-34
3. Adjusting the Lower Roller
Pressure (nip) ............... 13-36
F. Laser Exposure System .... 13-37
1 After Replacing the Laser Unit
..................................... 13-37
2 Checking the Laser Power
..................................... 13-38
G. Electrical Parts .................. 13-41
1 After Replacing the CCD Unit
..................................... 13-41
2 After Replacing the Image
Processor PCB ............. 13-42
3 After Replacing the MFC PCB
..................................... 13-43
4. After Replacing the Hard Disk
..................................... 13-44
5. After Replacing the DC
Controller PCB ............. 13-45
6. Checking the Surface
Potential Control System
..................................... 13-45
7. Checking the Potential
System ......................... 13-51
xv