Pacific Power Source LMX Series Operation Manual page 7

8.1.2 Command Terminators .................................................................................................................................. 203
8.2 Remote Control Command Descriptions by Subsystem ................................................................... 204
8.3 Calibration Commands ........................................................................................................................ 205
8.3.1 LMX Calibration Commands .......................................................................................................................... 205
8.3.2 UPC Specific commands. ................................................................................................................................ 207
8.3.3 AUX I/O Interface Calibration Commands .................................................................................................... 207
8.4 Measurement Commands .................................................................................................................. 208
8.4.1 Voltage Measurement Commands ............................................................................................................... 208
8.4.2 Frequency Measurement Commands .......................................................................................................... 209
8.4.3 Current Measurement Commands ............................................................................................................... 209
8.4.4 Power Measurement Commands ................................................................................................................. 211
8.4.5 KWh Measurement Commands .................................................................................................................... 211
8.4.6 Other Measurement Commands .................................................................................................................. 212
8.4.7 Measurement Data Logging Commands ...................................................................................................... 213
8.4.8 Waveform Capture Commands ..................................................................................................................... 217
8.4.9 Harmonic Measurements Commands .......................................................................................................... 219
8.5 Output Control Commands ................................................................................................................ 224
8.6 Program Commands ........................................................................................................................... 228
8.6.1 Program Control Commands ......................................................................................................................... 228
8.6.2 Execution Commands..................................................................................................................................... 236
8.6.3 Transient Segments Commands .................................................................................................................... 237
8.6.4 Memory Management Commands ............................................................................................................... 242
8.7 Source Commands .............................................................................................................................. 245
8.7.1 Source Configuration Programming Commands .......................................................................................... 245
8.7.2 Voltage Programming Commands ................................................................................................................ 249
8.7.3 Frequency Programming Commands............................................................................................................ 254
8.7.4 Current Programming Commands ................................................................................................................ 255
8.7.5 Phase Programming Commands ................................................................................................................... 258
8.7.6 Waveform Programming Commands ........................................................................................................... 260
8.7.7 Voltage Protection Programming Commands .............................................................................................. 268
8.7.8 Current Protection Programming Commands .............................................................................................. 270
8.7.9 Power Protection Programming Commands ................................................................................................ 272
8.7.10 Impedance Programming Commands .......................................................................................................... 278
8.7.11 STEP Transient Commands ............................................................................................................................ 281
8.7.12 PULSE Transient Commands .......................................................................................................................... 298
8.7.13 IEC413 Option Interharmonics Commands .................................................................................................. 309
8.8 Status Commands ............................................................................................................................... 313
8.9 System Commands .............................................................................................................................. 315
8.9.1 System Error Commands ............................................................................................................................... 315
8.9.2 System Information Commands .................................................................................................................... 316
8.9.3 System Interface Soft Key Preset Commands ............................................................................................... 319
8.9.4 System Configuration Commands ................................................................................................................. 323
8.9.5 Parallel System Commands ............................................................................................................................ 325
8.9.6 System Sanitization Commands .................................................................................................................... 326
8.9.7 Communication LAN Commands .................................................................................................................. 326
8.9.8 Communication Serial Port Commands ........................................................................................................ 330
8.9.9 Communication USB Commands .................................................................................................................. 331
8.9.10 Communication GPIB Commands ................................................................................................................. 333
8.9.11 System Firmware Commands ........................................................................................................................ 334
8.9.12 System Remote Access Commands .............................................................................................................. 335
8.9.13 Miscellaneous System Commands ................................................................................................................ 336
8.10 Auxiliary I/O System Commands ........................................................................................................ 337
8.10.1 Analog & Digital IO Programming Commands .............................................................................................. 337
8.10.2 SOURce:SYNChronize Commands ................................................................................................................. 350

Entire Contents Copyright 2018 by Pacific Power Source, Inc. (PPS) • All Rights Reserved • No reproduction without written authorization from PPS.
LMX Series Power Source Operation Manual
LMX SERIES™ OPERATION MANUAL
Page 7 of 463
CONTENTS