JVL MAC050 User Manual page 423

6.12
Firmware /
MacRegIo Name
21 U_24V
22 FLWERRMAX
23 UV_HANDLE
24 FNCERR
25 P_IST_TURNTAB
26 FNCERRMAX
27 TURNTAB_COUN
T
28 MIN_P_IST
29 DEGC
30 MAX_P_IST
31 DEGCMAX
32 ACC_EMERG
JVL A/S - User Manual - Integrated Servo Motors MAC050 - 4500
Registers
MacTal Size /
k Name Acces
Na / Word /
0 R
Na / Word /
0 RW
- Na / Word /
Set 0 RW
error
bit
-
Go to
passiv
e
-
Set
velocit
y to 0
Na / Word /
(not
0 RW
present)
Na / Word /
(not
0 R
present)
Na / Word /
(not
present) 0 RW
Na / Word /
(not
present) 0 RW
Na / Word /
(not
0 RW
present)
Na / Word /
(not
present) 0 R
Na / Word /
(not
0 RW
present)
Na / Word /
(not
present) 690 R
(84'C
)
Na / Word /
(not
0 RW
present)
Unit Description
The internal control voltage measured.
Encoder When Reg20, FLWERR, exceeds this limit, bit 1,
counts FLW_ERR, in Reg35, ERR_STAT, is set and the
motor will stop if Reg22 is non-zero. Usually this value
is set experimentally to detect situations where a
movement is blocked or fails.
Bits to determine what will happen when the main
supply voltage to the motor is below the threshold for
motor operation. Any combination of the following bits
can be set.
Bit 0: Set bit 9, UV_ERR, in Reg35, ERR_STAT.
Bit 1: Perform a controlled stop, then go passive.
Bit 2: Set V_SOLL to zero, do not go passive.
Encoder Shows how much the motor is behind the ideal
counts movement; precise operation depends on mode.
When this accumulated value exceeds Reg26,
FNCERRMAX, the FNC_ERR bit is set in Reg35,
ERR_STAT and the motor will stop.
- Displays the actual position, like P_IST, but is offset
by N times the rotary table working range so
P_IST_TURNTAB is always between MIN_P_IST and
MAX_P_IST. Used mainly with the Rotary table
option.
Encoder The limit used with Reg24, FNCERR.
counts
- Holds a count of the number of times the value of
Reg25, P_IST, wraps around one of its limits,
MIN_P_IST or MAX_P_IST. Used only with the Rotary
table option. Counts up or down depending on the
direction of the wrap around.
Encoder Used to define and enable the minimum software
counts position limit, so the motor will stop (and enter passive
mode) if the value of P_IST (the actual position) gets
below this value. If MIN_P_IST is zero, the low
position limit will not be enabled. In Rotary Table
operation, this limit is used as the lower wrap-around
position count.
-> The temperature measured inside the drive.
Approximately 0.1221 Degree Celsius per count.
Encoder Used to define and enable the maximum software
counts position limit, so the motor will stop (and enter passive
mode) if the value of P_IST (the actual position) gets
above this value. If MAX_P_IST is zero, the high
position limit will not be enabled. In Rotary Table
operation, this limit is used as the higher wrap-around
position count
- The maximum value of Reg29, DEGC, before the
motor will set the Temperature error bit in ERR_STAT
and change into Passive mode. Same scaling as
Reg29, DEGC.
- Acceleration to use during emergency stops.
Only MAC400 to 4500
TT1503-02GB
419