YASKAWA HV600 Technical Reference page 791

Parameters (keypad to drive) ..................................... 146
Reverse Operation Selection........................................... 191
RJ-45 connector ......................................................... 119
Rotational Auto-Tuning
Induction Motor .................................................... 169
Precautions .......................................................... 170
Run command ........................................................... 188
Run Command at Power Up ........................................... 195
S
S-curve characteristics
Parameter ............................................................ 228
SAFE...................................................................... 507
Sampling time setting
Data log .............................................................. 162
SC ......................................................................... 493
SCF........................................................................ 493
Schematic ................................................................. 72
SE ......................................................................... 507
Sequence Timer
HOME screen display.............................................. 379
Sequence Timers ........................................................ 376
SEr ........................................................................ 493
Set date and time
Operation ............................................................ 157
Set time
Operation ............................................................ 157
Setpoint selection
System Feedback Monitor......................................... 419
Side-by-side
Derating.............................................................. 345
Simple Positioning Stop................................................ 241
Sleep Function
Sleep.................................................................. 412
Wake-up ............................................................. 412
Sleep Wake-up level
Absolute Mode...................................................... 412
Delta to Setpoint Mode ............................................ 412
Slip compensation
Parameter ............................................................ 229
SMK_ALRM ............................................................ 507
Softcharge Relay Maintenance Set ................................... 367
Software Current Limit Selection
Protective function ................................................. 344
Software version
Display procedure .................................................. 165
Speed Agreement
Parameter ............................................................ 328
Speed Detection
Parameter ............................................................ 328
Speed Estimation Speed Search ....................................... 199
Speed Search function
Operation during momentary power loss........................ 320
Parameter ............................................................ 197
Stall Prevention function
Parameter ............................................................ 322
Stationary Auto-Tuning
Induction Motor .................................................... 169
Precautions .......................................................... 170
Stationary Auto-Tuning for Line-to-Line Resistance .............. 169
Precautions .......................................................... 170
Stator resistance Auto-Tuning
Precautions .......................................................... 170
YASKAWA SIEPYAIH6B01A HV600 AC Drive Bypass Technical Reference
STo ........................................................................ 507
SToF ...................................................................... 507
Stop command ........................................................... 188
Stopping Method Selection ............................................ 189
STPo ...................................................................... 493
Surge protective device
Connection .......................................................... 114
T
Temperature
Environment.......................................................... 34
Terminal function selection
Terminal A1 ......................................................... 106
Terminal A2 ......................................................... 106
Terminal AM........................................................ 107
Terminal FM ........................................................ 107
Termination resistor
Setting switch ....................................................... 107
Test run
Fine tuning .......................................................... 171
Thrust Mode
Thrust frequency.................................................... 416
Tightening torque
Main circuit terminals............................................... 81
TiM
Fault .................................................................. 493
Minor Fault.......................................................... 507
Timer function
Parameter ............................................................ 206
Torque Compensation
Parameter ............................................................ 230
Trend Plot
Monitors ............................................................. 138
Troubleshooting
Code Displayed ............................................... 459, 466
No Code Displayed................................................. 520
Troubleshooting without Fault Display .............................. 520
TrPC....................................................................... 508
Tuning .................................................................... 227
U
U2, U3 Initialization .................................................... 368
UL3
Fault .................................................................. 494
Minor Fault.......................................................... 508
UL4
Fault .................................................................. 494
Minor Fault.......................................................... 508
UL6
Fault .................................................................. 494
Minor Fault.......................................................... 508
Undertorque detection
Parameter ............................................................ 336
Unit selector ............................................................. 362
Up command
Parameter ...................................................... 240–241
USB port ................................................................. 119
Connecting a PC .................................................... 109
User Parameter Default Value ......................................... 363
User-Set Display Units Max Value ................................... 357
User-SetDisplayUnits Dec Display ................................... 357
Uv ......................................................................... 508
Speed Search Selection at Start................................... 206
Uv1........................................................................ 494
791