YASKAWA HV600 Technical Reference page 658

9.16 Y: Application Features
No.
Name
(Hex.)
Y1-15 Maximum Setpoint
Difference
(3C0E)
RUN
Y1-16 Not Maintaining Setpoint
Time
(3C0F)
RUN
Y1-17 Not Maintaining Setpoint
Sel
(3C10)
Y1-18 Prime Loss Detection
Method
(3C11)
Y1-19 Prime Loss Level
(3C12)
RUN
Y1-20 Prime Loss Time
(3C13)
RUN
Y1-21 Prime Loss Activation
Freq
(3C14)
Y1-22 Prime Loss Selection
(3C15)
Y1-23 Prime Loss Max Restart
Time
(3C16)
Y1-40 Maximum Speed
(3C27)
RUN
◆
Y2: PID Sleep and Protection
No.
Name
(Hex.)
Y2-01 Sleep Level Type
(3C64)
Y2-02 Sleep Level
(3C65)
RUN
658
Sets a percentage of difference between the setpoint and the feedback. The difference must
be more than this value for the time set in Y1-16 [Not Maintaining Setpoint Time] to
trigger the drive response set in Y1-17 [Not Maintaining Setpoint Sel].
Note:
• Unit and decimal place change when the system units change.
• If there is a fault, the drive will coast to a stop.
• Set this parameter to 0.0 to disable the function.
• This function is only active during run when in Auto Mode.
Sets the delay time before a Setpoint Not Met condition occurs. The drive must detect the
setpoint difference set in Y1-15 [Maximum Setpoint Difference] before the timer will start.
Note:
Set Y1-15 = 0 [Maximum Setpoint Difference = 0] to disable this function.
Sets the drive response when the feedback increases to more or decreases to less than the
setpoint for more than the amount set in Y1-15 [Maximum Setpoint Difference].
0 : Fault (and Digital Output)
1 : Alarm (and Digital Output)
2 : Digital Output Only
Sets the units and quantity that the drive will use to determine LOP [Loss of Prime].
0 : Current (A)
1 : Power (kW)
2 : Torque (%)
Sets the level to detect the LOP [Loss of Prime] in the pump when in Auto or Sleep Boost
Mode.
Sets the delay time before the drive detects an LOP [Loss of Prime] condition. The timer
starts when the drive detects the conditions in Y1-18 [Prime Loss Detection Method] and
Y1-19 [Prime Loss Level].
Sets the frequency level above which the drive enables Loss of Prime detection.
Sets the drive response when the drive is in the Loss of Prime condition.
0 : Fault (and Digital Output)
1 : Alarm (and Digital Output)
2 : Digital Output Only
Sets the time in minutes that the drive will wait before it tries a restart after a restart fails or
after it does not do a restart because of a fault.
Sets the maximum speed.
Note:
This parameter is not effective when Y1-40 = 0.0 Hz or Y1-40 > E1-04 [Maximum
Output Frequency] × d2-01 [Frequency Reference Upper Limit].
Sets the data source that the drive uses to know when to activate the Sleep Function.
0 : Output Frequency
1 : Output Current
2 : Feedback
3 : Output Speed (RPM)
5 : Output Frequency (non-PID)
Note:
• Feedback depends on PID direction operation.
• When the Sleep Function is active, the keypad will show the "Sleep" Alarm.
Sets the level that the level type set in Y2-01 [Sleep Level Type] must be at for the time set
in Y2-03 [Sleep Delay Time] for the drive to enter Sleep Mode.
Note:
• When you set this parameter to 0.0, this function will not be active.
• This function is active only when the drive operates in AUTO Mode.
• When Y2-01 = 5 [Output Frequency (non-PID)], the drive will disable the Sleep
function when you set this parameter to 0.0.
• When Y2-01 ≠ 5, the drive will set the sleep level to the largest value from d2-02
[Frequency Reference Lower Limit], Y1-06 [Minimum Speed], and Y4-12 [Thrust
Frequency] when you set this parameter to 0.0.
Description
Description
YASKAWA SIEPYAIH6B01A HV600 AC Drive Bypass Technical Reference
Default
Ref.
(Range)
0.0% 409
(0.0 - 6000.0%)
60 s 410
(0 - 3600 s)
0 410
(0 - 2)
0 410
(0 - 2)
0.0 411
(0.0 - 1000.0)
20 s 411
(0 - 600 s)
0.0 Hz 411
(0.0 - 400.0)
0 411
(0 - 2)
0.2 min 411
(0.2 - 6000.0 min)
0.0 Hz 412
(0.0 - 416.0)
Default
Ref.
(Range)
5 413
(0 - 5)
0.0 413
(0.0 - 6000.0)