Seat Leon 2013 Workshop Manual page 301

Front axle
a)
PR no.
Maximum permissible differ‐
ence between sides
Maximum wheel turning angle
(not adjustable)
Ground clearance
⇒ page 296
3) Camber cannot be adjusted. Corrections are possible by moving the subframe
slightly.
4) The toe-out on turns can be displayed as a negative value on the wheel align‐
ment computer, depending on the manufacturer.
Rear axle
Total toe
Max. permissible deviation
from direction of travel
Camber
Maximum permissible differ‐
ence between sides
Ground clearance
⇒ page 296
Multi-link suspension
a)
⇒ "1.13 Vehicle data label", page 309
Front axle
a)
PR no.
Total toe
Camber (wheels
straight)
5)
Maximum permissible
difference between
sides
Differential angle of
convergence with the
wheels at 20°
6)
Caster
Maximum permissible
difference between
sides
Standard running
gear
G01/G02/G04 +
2UA
G17
Max. 30'
40° 38'
384 mm
Standard running
gear
With torsion
beam axle (VL)
20' ± 10'
Max. 10'
-1° ± 10'
Max. 30'
381 mm
Standard Running
running gear gear for
sports model
G01/G02/ G02/G03/
G04 + 2UA G05 + 2UC
G17 G02 + 2UP
G14/G16
10' ± 10' 10' ± 10'
-30' ± 30' -41' ± 30'
Max. 30' Max. 30'
1° 19' ± 20' 1° 20' ± 20'
7° 23' ± 30' 7° 38' ± 30'
Max. 30' Max. 30'
León 2013 ➤ , León ST 2013 ➤
Running gear, axles, steering - Edition 06.2018
Running gear for Running gear for
sports model poor roads
G02/G03/G05 + G01/G02/ + 2UF
2UC G15/G18
G02 + 2UP G14/
G16
Max. 30' Max. 30'
40° 13'
369 mm 399 mm
Running gear for Running gear for
sports model poor roads
With torsion With torsion
beam axle (VL) beam axle (VL)
24' ± 10' 16' ± 10'
Max. 10' Max. 10'
-1° ± 10' -1° ± 10'
Max. 30' Max. 30'
366 mm 396 mm
Running Running
gear for poor gear for poor
roads roads
G01/G02/ + G03/G04 +
2UF G15/ 2UF
G18
10' ± 10' 10' ± 10'
-16' ± 30' -30' ± 30'
Max. 30' Max. 30'
1° 09' ± 20' 1° 19' ± 20' 1° 42' ± 20' 1° 30' ± 20'
7° 09' ± 30' 7° 23' ± 30' 7° 52' ± 30' 7° 38' ± 30'
Max. 30' Max. 30'
Running gear for
poor roads
G03/G04 + 2UF
Max. 30'
41° 05' 40° 38'
384 mm
Running gear for
poor roads
With torsion
beam axle (VL)
20' ± 10'
Max. 10'
-1° ± 10'
Max. 30'
381 mm
Cupra run‐ Cupra run‐
ning gear ning gear
with DCC without DCC
G05 + 2UG G04 + 2UC
10' ± 10' 10' ± 10'
-47' ± 30' -41' ± 30'
Max. 30' Max. 30'
Max. 30' Max. 30'
1. Wheel alignment
295