Delta C2000 Series User Manual page 555

Chapter 12 Description of Parameter SettingsC2000
Modbus
address
2205H
2206H
2207H
2208H
2209H
220AH
220BH
220CH
220DH
220EH
220FH
2210H
2211H
2212H
2213H
2214H
2215H
2216H
2217H
2218H
2219H
221AH
221BH
221CH
221DH
221EH
221FH
2220H
2221H
2222H
2223H
2224H
2225H
2226H
RW
R Power angle (XXX.X)
R Display actual motor speed kW of U, V, W (XXXXX kW)
Display motor speed in rpm estimated by the drive or encoder feedback
R
(XXXXX rpm)
Display positive/negative output torque in %, estimated by the drive (t0.0:
R
positive torque, -0.0: negative torque) (XXX.X %)
R Display PG feedback (see NOTE 1 in Pr. 00-04)
R PID feedback value after enabling PID function (XXX.XX %)
Display signal of AVI analog input terminal, 0–10V corresponds to
R
0.00–100.00% (1.) (see NOTE 2 in Pr. 00-04)
Display signal of ACI analog input terminal, 4–20mA / 0–10V corresponds to
R
0.00–100.00% (2.) (see NOTE 2 in Pr. 00-04)
Display signal of AUI analog input terminal, -10V–10V corresponds to
R
-100.00–100% (3.) (see NOTE 2 in Pr. 00-04)
R IGBT temperature of drive power module (XXX.X ºC)
R The temperature of capacitance (XXX.X ºC)
The status of digital input (ON/OFF), refer to Pr. 02-12
R
(see NOTE 3 in Pr. 00-04)
The status of digital output (ON/OFF), refer to Pr. 02-18
R
(see NOTE 4 in Pr. 00-04)
R The multi-step speed that is executing (S)
The corresponding CPU pin status of digital input (d.)
R
(see NOTE 3 in Pr. 00-04)
The corresponding CPU pin status of digital output (O.)
R
(see NOTE 4 in Pr. 00-04)
Number of actual motor revolution (PG1 of PG card) (P.) it starts from 9
R when the actual operation direction is changed or the keypad displays at
stop is 0. The maximum is 65535
R Pulse input frequency (PG2 of PG card) (XXX.XX Hz)
R Pulse input position (PG card PG2), the maximum setting is 65535.
R Position command tracing error
R Display times of counter overload (XXX.XX %)
R GFF (XXX.XX %)
R DCBUS voltage ripples (XXX.X V)
R PLC register D1043 data (C)
R Number of poles of a permanent magnet motor
R User page displays the value in physical measure
R Output Value of Pr. 00-05 (XXX.XX Hz)
Number of motor turns when drive operates (saves when drive stops, and
R
resets to zero when operating)
Operating position of the motor (saves when drive stops, and resets to zero
R
when operating)
R Fan speed of the drive (XXX %)
R Control mode of the drive 0: speed mode 1: torque mode
R Carrier frequency of the drive (XX kHz)
R Reserve
Drive
status 00b: No direction
bit1–0 01b: Forward
10b: Reverse
R
bit3–2 01b: Drive ready
10b: Error
bit4 0b: Motor drive did not output
1b: Motor drive did output
Function
12.1-09-10