Nortel DMS-10 Series Installation, Operation And Maintenance Manual
Nortel DMS-10 Series Installation, Operation And Maintenance Manual

Nortel DMS-10 Series Installation, Operation And Maintenance Manual

Billing media converter ii
Hide thumbs Also See for DMS-10 Series:
Table of Contents

Advertisement

297-6201-502
DMS-10 and DMS-100 Families
Billing Media Converter II
BISYNC Operation, Administration, and Maintenance Guide
BMCB001 and up
Standard
01.02
September 2000

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DMS-10 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Nortel DMS-10 Series

  • Page 1 297-6201-502 DMS-10 and DMS-100 Families Billing Media Converter II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up Standard 01.02 September 2000...
  • Page 3 Information is subject to change without notice. Nortel Networks reserves the right to make changes in design or components as progress in engineering and manufacturing may warrant. Changes or modification to the DMS-100 without the express consent of Nortel Networks may void its warranty and void the users authority to operate the equipment.
  • Page 5 Publication history Standard Issue 1.01 November 1997 • First standard issue. Standard Issue 1.02 December 2000 BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 7: Table Of Contents

    Contents Section 060-INDP-110 System Index ..... 1-1 Section List ............1-1 060-INDP-110 - System Index .
  • Page 8 vi Contents Power Supply Fuse and Circuit Breaker ......2-29 System Temperature Sensor(s) ........2-31 Maintenance Considerations .
  • Page 9 Contents vii Disk Initialization ..........2-77 Files .
  • Page 10 viii Contents Switching System Specific Commands ......4-1 Priority Levels ..........4-1 Prompts .
  • Page 11 Contents ix DELFILE ..........4-39 DMPFILE .
  • Page 12 x Contents Firmware Commands ..........4-77 BYE .
  • Page 13 Contents xi Disk Drive Capacity Error Procedure ....... 6-39 Disk Drive Diagnostic Procedure ........6-39 Disk Drive Full Procedure .
  • Page 14 xii Contents Maintenance Terminal Information ........8-10 Connecting Maintenance Terminals to BMC .
  • Page 15 Contents xiii CP LOAD FAIL message ......... 4-124 CP LP CODE xx WAS yy message .
  • Page 16 xiv Contents DISK: RST-7 message ......... . . 4-177 DISK: x FAILURE message .
  • Page 17 Contents xv LINK xx RETRY THRESH EXCEEDED, MSG: mm nn message ..4-220 LOG FILE DELETED message ........4-221 MPSR ERR message .
  • Page 18 xvi Contents xxxIDX FILE FULL message ........4-265 xxxIDX FILE OPEN ERROR : 03 message .
  • Page 19 Contents xvii NT3T11 - BMC Data Interface Cables ....... . . 7-5 Installing NT3T11 PCA in NT3T11 enclosure .
  • Page 20 xviii Contents Quad SIO PCA (NT6M60xx) Diagnostic ......6-96 Secondary Data Polling ......... . . 6-99 Site File Error .
  • Page 21 Contents xix ERRMAP device/event names ........4-7 RSERR subcommands .
  • Page 23 About this document When to use this document This document contains the operation, administration and maintenance for the Billing Media Converter II (BMC II). This document contains information specific to BMC II Bisynchronous (BISYNC) systems equipped with 3 1/2” disk drives (1 gigabyte of capacity). This document is not intended for use with BMC II BISYNC systems equipped with 5 1/4”...
  • Page 24 LATA Switching System Generic Requirements (LSSGR), TR-TSY-000064, PUB 48501. What precautionary messages mean The types of precautionary messages used in Northern Telecom (Nortel) documents include warning and caution messages. Warning and caution messages indicate possible risks. Example of the precautionary messages follow.
  • Page 25 xxiii Input prompt (>) An input prompt (>) indicates that the information that follows is a command: >BSY Commands and fixed parameters Commands and fixed parameters that are entered at a MAP terminal are shown in uppercase letters: >BSY CTRL Variables Variables are shown in lowercase letters: >BSY CTRL ctrl_no...
  • Page 27 The numbers associated with each section are taken from the long-standing format of the BMC documentation prepared by the Cook Electric Division of Nortel. Some of the sections found in the original Cook Electric Division manuals are not replicated in this document.
  • Page 28: 1-2 Section 060-Indp-110 System Index

    1-2 Section 060-INDP-110 System Index 060-INDP-111 - System Description This section provides an overview of the hardware and software elements of the BMC system. 060-INDP-310 - System Administration This section provides procedures and information to coordinate and manage the BMC. 060-INDP-410 - Command and Message Guide This section provides information for the user to enter BMC commands and interpret system messages.
  • Page 29 HOC can remotely access and request call records. Polling functions are conducted through the use of the BISYNC 3270 or 3780 protocol. New software downloads are offered from a Nortel-based host using the ASCII protocol (Pollstar not required).
  • Page 30: 2-2 Section 060-Indp-111 System Description

    2-2 Section 060-INDP-111 System Description System description - Hardware The BMC consists of two processor units physically connected together. Figure 2-1 provides a view of the general appearance of the BMC. The two processor units are electronically linked through crossover capability, which enables either unit to communicate with either of the disk drives.
  • Page 31 Section 060-INDP-111 System Description 2-3 Figure 3-1 Billing Media Converter II BMC II Billing Media Converter II BMC II Billing Media Converter II BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 32 2-4 Section 060-INDP-111 System Description Figure 3-1 BMC cabinet dimensions 17.52 in. (445 mm) Shipping 14.25 in. Bracket (362 mm) TOP VIEW 24.34 in. (618 mm) FRONT VIEW 19.00 in. (482.6 mm) 297-6201-502 Standard 01.02 September 2000...
  • Page 33 Section 060-INDP-111 System Description 2-5 Figure 3-1 Data and Peripheral Interface connectors DMS-10 Not Available DMS-100 Optional Remote MTC Port 3 Software Download DMS-10 SDI Port DMS-100 Optional Remote MTC Port 2 MTC Port 1 TEC/DSI1 (slot 13; A and B chassis) TEC/DSI0 (slot 12;...
  • Page 34 2-6 Section 060-INDP-111 System Description Figure 3-1 Power, Ground and Alarm Interface connectors Alarms DC Input Power Frame Ground Stud DMS-10 Only +12V fuse for J17 (fused at 5A. 12 volt power from the BMC to 3T11 Interface Box. +12 volt power is not wired for other applications.
  • Page 35 Section 060-INDP-111 System Description 2-7 Figure 3-1 BMC cabinet subassemblies Processor A Switch and Circuit Boards Status Panel A1-----------------------A14 Processor A chassis A20 Power Supply A21 Disk Drive A B20 Power Supply B21 Disk Drive B Processor B chassis B1------------------------B14 Filler Panel Processor B Circuit Boards...
  • Page 36: J-Connector Identification

    2-8 Section 060-INDP-111 System Description J-Connector identification These connectors, located on certain subassemblies, are identified by the letter J, followed by up to three digits. For example, both the A and B chassis have J-connectors on the pin side of the backplane; numbers increasing from right to left.
  • Page 37: Pca Racks

    Section 060-INDP-111 System Description 2-9 PCA racks Typical subassembly and circuit assembly locations are shown in Figure 2-6. The illustration shows that two PCA racks (A and B) are used. PCAs are designated A1 through A14 in the A (upper) chassis; B1 through B14 in the B (lower) chassis.
  • Page 38 B1 CPU LOGIC PCA A1 CPU LOGIC PCA B2 EPROM PCA A2 EPROM PCA B3 MEMORY EXPANSION PCA A3 MEMORY EXPANSION PCA B5 ERROR CONTROL II JUMPER PCA A5 ERROR CONTROL II PCA B6 QUAD SIO PCA A6 QUAD SIO PCA B7 56K INTERFACE PCA A7 56K INTERFACE PCA B11 SCSI INTERFACE PCA...
  • Page 39 Section 060-INDP-111 System Description 2-11 Figure 3-1 Auxiliary circuit assembly locations Left rear of chassis (with cabinet back removed) Hinged card panel (closed) Power and Alarm Communications PCA (A16) or 56K Crossover PCA (B16) a. View with hinged card panel closed SCSI Crossover PCA (A15 and B15) (opposite side of hinged panel)
  • Page 40: List Of Equipment Assemblies And Subassemblies

    2-12 Section 060-INDP-111 System Description List of equipment assemblies and subassemblies Table 2-1 lists the assemblies and subassemblies used in the BMC system. The list provides reference designations, abbreviated names, full names, part numbers, and usage notes, where applicable. Table 2-1 List of assemblies and subassemblies Reference ABBR...
  • Page 41 Section 060-INDP-111 System Description 2-13 Table 2-1 List of assemblies and subassemblies Reference ABBR Full name - part number - usage notes designat name Bus Terminator PCA - NT6M68AA TERM SCSI SCSI Crossover PCA (located on inner portion of hinged panel at rear XOVR of upper chassis) - NT6M93BA Power and Alarm Communications PCA (located on the outer portion...
  • Page 42 2-14 Section 060-INDP-111 System Description Table 2-1 List of assemblies and subassemblies Reference ABBR Full name - part number - usage notes designat name ERCJ Error Control II Jumper PCA - NTM609AB QUAD Quad Serial Input/Output PCA - NT6M60BA 56K Interface PCA - NT6M94AA INTF SCSI SCSI Interface PCA - NT6M66CA...
  • Page 43 Section 060-INDP-111 System Description 2-15 Table 2-1 List of assemblies and subassemblies Reference ABBR Full name - part number - usage notes designat name DISK Disk Drive Assembly - NT6M72GA a. 3 1/2” disk drive with a 1-Gbyte capacity b. use option jumper to identify the B disk at position B21 56K Connector - NT6M54AL a.
  • Page 44: List Of Hardware Spare Kits

    2-16 Section 060-INDP-111 System Description List of Hardware Spare Kits Table 2-2 List of Hardware Spare Kits Description NT6M91WE Minimum BMC spares package for DMS-10 system with 3.5” disk drives (disk drive not included). The following items are standard in this spares kit: NT6M96AA - fuse kit NT6M84BA - Power and Alarm Communications PCA NT6M65AG - Memory Expansion PCA...
  • Page 45 Section 060-INDP-111 System Description 2-17 Table 2-2 List of Hardware Spare Kits Description NT6M94WE Minimum BMC spares package for DMS-100 system with 3.5” disk drives (disk drive not included). The following items are standard in this spares kit: NT6M96AA - fuse kit NT6M84BA - Power and Alarm Communications PCA NT6M65AG - Memory Expansion PCA NT6M70BD - DSI PCA...
  • Page 46: Pca Functions

    2-18 Section 060-INDP-111 System Description PCA Functions The following subsections describe the PCAs that comprise the BMC. Central Processor Unit Logic PCA The CPU PCA is located in slot 1 of the A and B chassis. The CPU, which has DMA, organizes data flow throughout the BMC. Its operations can be classified according to the functions of its four major Integrated Circuits (ICs): •...
  • Page 47: Ecac Alarm Reporting Priority Sequence - Led Display Codes

    Section 060-INDP-111 System Description 2-19 Table 2-3 ECAC alarm reporting priority sequence - LED display codes Level Category Response Notes Major Invalid CPU Response Critical Critical Processor switch occurs. Level 3 Critical Critical Processor switch occurs. Level 2 Critical Critical Processor switch occurs.
  • Page 48: Erasable Programmable Read-Only Memory Pca

    2-20 Section 060-INDP-111 System Description Table 2-3 ECAC alarm reporting priority sequence - LED display codes Level Category Response Notes None Planned processor switch. None All systems operational. Table 2-4 CPU display control functions Mode SW2-3 SW2-4 Description Monitor Error Standard setting: data written to the error control port I/01 Control Port (88-8B;...
  • Page 49: Error Control Ii And Error Control Ii Jumper Pcas

    Section 060-INDP-111 System Description 2-21 ically by the CPU to maintain its programmed state. Each DRAM Expansion PCA contains up to 128 Kbytes of DRAM. On the system level, DRAM pro- vides storage of temporary data, such as system calculations, and updating of statistics.
  • Page 50: 56K Interface Pca

    2-22 Section 060-INDP-111 System Description active processor, four of them buffered by a tri-state octal buffer. Another tri- state octal buffer circuit buffers the ten control lines used by the processor. The Quad SIO PCA reports internal faults to the active processor by generating signal interrupts.
  • Page 51: Scsi Interface Pca

    Section 060-INDP-111 System Description 2-23 clock is used because the clock available on the PCA (12 MHz) exceeds chip capability. The 6MHz (12 MHz divided by two) provided by the CPU is too slow for adequate SCC response. The 56K Interface PCA requires +5 V dc +/- 0.25 volts. This is accomplished by the 5 volt regulator on the PCA which uses the +8.5 V dc supply from the backplane.
  • Page 52 2-24 Section 060-INDP-111 System Description RAM (DPR). It is considered a peripheral of the microprocessor on the main CPU (A1). The SCSI Interface PCA is the link to the disk drive. It transfers data from and to the bus used for recording on or reading from the disk. The stored program on the SCSI Interface PCA provides read and write commands to the disk drive.
  • Page 53: Tape Emulation Circuit/Data Stream Interface Pca

    Section 060-INDP-111 System Description 2-25 Tape Emulation Circuit/Data Stream Interface PCA The BMC application eliminates the Magnetic Tape Drives (MTDs) used with the Switching Systems to collect Automatic Message Accounting (AMA) data. The four TEC/DSI PCAs (slots 12 and 13 in the A and B chassis) in the BMC replace the MTDs.
  • Page 54: Power And Alarm Communications Pca

    2-26 Section 060-INDP-111 System Description provided for each of the two SCSI Interface PCAs. The SCSI port provides the system interface to the SCSI disk drives. Power from both A and B chassis is provided at this connector in a diode OR’ed arrangement for redundancy purposes.
  • Page 55 Section 060-INDP-111 System Description 2-27 The P/A Comm PCA contains four serial channels configured as a 2-input, 1-output switch. The input is connected to the Quad SIO PCAs in the BMC chassis. The input interface consists of eight signal lines (plus ground) for each channel.
  • Page 56: 56K Crossover Pca

    2-28 Section 060-INDP-111 System Description 56K Crossover PCA The 56K Crossover PCA provides a dual high-speed serial communication crossover function for the BMC. This PCA provides both a V.35 (1200-9600 baud) and RS-232 (1200-9600 baud) interface circuit that allows the BMC to transmit and receive serial data at various standard software programmed rates from 1200 to 9600 bits per second.
  • Page 57: Fan Filter Pca

    Section 060-INDP-111 System Description 2-29 • nine EIA RS-232 leads for each of the four channels. • multiple logic ground lines. Fan Filter PCA The Fan Filter PCA suppresses fan noise generated within the BMC from being fed back into the -48 VDC source. 56K Connector PCA The 56K Connector PCA provides the physical interface between the serial communication channels of the BMC unit and external devices.
  • Page 58: Fuse Replacement Information

    (color) number Power Supply -48 VDC from CO 5 (green) 5 amp fuse: Buss GMT-5 or equivalent Nortel part number: A0108995 Input Connector +12 VDC (AUX) 5 (green) 5 amp fuse: Buss GMT-5 or equivalent Panel Nortel part number: A0108996...
  • Page 59: System Temperature Sensor(S)

    Section 060-INDP-111 System Description 2-31 System Temperature Sensor(s) The System Temperature Sensors are located inside the Power Supplies. These sensors provide an “early warning” alarm to indicate that the BMC is operating above its recommended operating temperature limits. The temperature at the sensor on the BMC power supply exceeds 120 -130 F due •...
  • Page 60: Fuses

    2-32 Section 060-INDP-111 System Description When performing any type of maintenance on the fan (fan not running), open the front cover of the BMC to improve convection cooling. Perform the necessary functions. Power down the -48 VDC when the fan is inoperable for extended periods of time to prevent damage from overheating.
  • Page 61: Power And Ground Requirements

    Section 060-INDP-111 System Description 2-33 Power and Ground Requirements The following subsections describe the power and ground requirements for the BMC. DC power requirements The BMC system receives dc power from the Central Office (CO) dc power system. Refer to Figure 2-9 for more information. Minimum operating voltage is -44 VDC;...
  • Page 62: Grounding Interface

    2-34 Section 060-INDP-111 System Description Grounding interface Internal grounding of the BMC is a star-type arrangement, with battery and chassis grounds isolated from each other. Connections for each of the grounds are indicated on the power and alarm connector panels. The arrangement of frame grounding conductors for the isolated ground plane and integrated ground plane frames and the interfaces with the CO grounding system are shown in Figure 2-9.
  • Page 63 Section 060-INDP-111 System Description 2-35 Connector J16 (External Alarms) Connector J16 is a 15-pin connector with male pins. The CRITICAL, MAJOR, MINOR, FAN (TEMPERATURE), FUSE and LOW POWER external alarm connections are provided at this connector. Table 2-7 Wiring for Connector J16 (A chassis only) Alarm Signal Description...
  • Page 64: Wiring For Connector J16 (A Chassis Only)

    2-36 Section 060-INDP-111 System Description Table 2-7 Wiring for Connector J16 (A chassis only) Alarm Signal Description Type Num. name Minor MIN COM Center (common) pin of contact set controlled by the minor alarm relay NO MINOR ALARM: closed, connected to pin 10 ANY MINOR ALARM: open NO MINOR ALARM: open ANY MINOR ALARM: connected to pin 10...
  • Page 65 Section 060-INDP-111 System Description 2-37 Table 2-8 Wiring for Connector J16 (B chassis only) Pin Num. Signal On Line Description of Pin Conditions Note: +12V AUX (A) Alarm is used for DMS-10 Switching Systems only. Not used +12V AUX B Chassis +12V Fuse intact: open (B) Alarm B Chassis +12V Fuse blown: connected to pin 5 +12V AUX...
  • Page 66: Disk Drives

    2-38 Section 060-INDP-111 System Description Connector J17 (+12V AUX) Connector J17 is a 3-pin connector with female pins. For DMS-100 Switching Systems, this is the location of the signal (Logic) ground used if the DMS-100 has the latest Isolated Signal Ground (ISG) wiring. Table 2-9 Wiring for Connector J17 Pin Num.
  • Page 67 Section 060-INDP-111 System Description 2-39 Figure 3-1 Disk drive mounting details Retainer Screw Extraction handle Rear Retainer Screw Top view Extraction handle Do not remove Retainer Front View Side View screw reference BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 68: Disk Drive Start-Up

    2-40 Section 060-INDP-111 System Description The disk drives also provide a permanent storage medium for entering site dependent data, system routines, message journals, and software files. Disk Drive Start-up When the BMC System is powered-up, either during initial installation procedures or after maintenance activities, closely observe the output messages.
  • Page 69: Disk Drive Commands

    Section 060-INDP-111 System Description 2-41 Table 2-10 Disk Drive Operating Modes Mode Description A Only - BMC processors read data from and write data to the disk in the A chassis ONLY. B Only - BMC processors read data from and write data to the disk in the B chassis ONLY.
  • Page 70: Switch And Status Panel Operation

    2-42 Section 060-INDP-111 System Description Switch and Status Panel Operation The following subsections describe the operation of the Switch and Status Panel. Processor mode changes at the Switch and Status Panel The following procedure is to be used whenever it becomes necessary to alter the operational configuration of the BMC processors using the Switch and Status Panel.
  • Page 71: Processor Mode Changes At The Terminal Keyboard

    Section 060-INDP-111 System Description 2-43 Table 2-11 BMC switch and status panel operation Initial processor mode A/B mode Only/Prime mode Final processor mode select switch select switch A PRIME B ONLY A ONLY A PRIME A ONLY B PRIME A ONLY B ONLY (see note) B PRIME B ONLY...
  • Page 72 2-44 Section 060-INDP-111 System Description This command is used to initiate a processor activity switch from the currently active processor the currently standby processor. 297-6201-502 Standard 01.02 September 2000...
  • Page 73 Section 060-INDP-111 System Description 2-45 Figure 3-1 BMC Switch and status panel Switch and Status Panel CRIT CHAS. GND. Filler Panel CHAS. GND. LEGEND: A Processor Status Lamps System Status Lamps ALM = Alarm CRIT = Critical = PRIME Mode MAJ = Major ONL = ONLY Mode MIN = Minor...
  • Page 74 2-46 Section 060-INDP-111 System Description To clear the active event/device alarms for the currently standby processor, followed by a processor activity switch, enter the following command: >SWACT FORCE (cr) CAUTION This action may cause a loss of data. The execution of either command produces the following sequence of expected messages: (only for SWACT FORCE command) ALL ALARMS CLEARED...
  • Page 75: Switch And Status Panel Indicators

    Section 060-INDP-111 System Description 2-47 Switch and status panel indicators The system provides lamps on the Switch and Status Panel for quickly ascertaining overall system operational conditions. Table 2-12 provides the color scheme and mnemonic identifier of the status and alarm lamps. BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 76 2-48 Section 060-INDP-111 System Description Table 2-12 Alarm lamp color scheme and identifiers Mnemonic Color Function Alarm (Active) Green PRIME Unit (status) Yellow ONLY Unit (status) CRIT Critical Alarm Major Alarm Yellow Minor Alarm 297-6201-502 Standard 01.02 September 2000...
  • Page 77: Central Processor Unit Led Display

    Section 060-INDP-111 System Description 2-49 The following paragraphs provide a brief description of the status and alarm lamps listed in Table 2-12. ALM (Alarm) Red indicator lamp (ALM) indicates that an alarm is in active status. When this lamp is active with other indicator lamps (CRIT, MAJ, or MIN), it is used to determine particular operational status (level of alarm).
  • Page 78: Error Control Ii Pca Jumper Led

    2-50 Section 060-INDP-111 System Description a decimal point feature that provides a visual display of the CPU clock. For the display to remain valid, the output to the display must occur every 0.5 second or less. Error Control II PCA Jumper LED The LED on the Error Control II Jumper PCA (slot B5) lights to indicate the toggle switch on the PCA has been activated (up position).
  • Page 79 Section 060-INDP-111 System Description 2-51 time. This information should, in turn, be used to determine when block checks should occur. To examine the hour boundaries currently assigned, enter the following at the maintenance terminal: >AMAHRS (cr) The system response is: BLOCK CHECK START xx END yy HOURS, INTERVAL OF zz MINUTES where: xx - block check start time (hour of the day) yy - block check end time (hour of the day)
  • Page 80 2-52 Section 060-INDP-111 System Description BMC systems for DMS-100 Switching Systems can be equipped with Enhanced Alarm Cables, which enable a temperature alarm system error message to be issued at the maintenance terminal. Low Voltage Alarm The low voltage alarm is activated when the voltage output of the BMC power supply drops below a given threshold.
  • Page 81: Bmc Test Function And Diagnostics

    Section 060-INDP-111 System Description 2-53 BMC Test Function and Diagnostics The TEST command is used to verify the proper operation of various functions that reside in the System. The following paragraphs provide a general description of the TEST command and a brief description of the various functions incorporated in the TEST command.
  • Page 82: Active Processor Test Command Functions And Availability

    2-54 Section 060-INDP-111 System Description Table 2-13 Active Processor TEST Command Functions and Availability Test Pass Test Error Indication Indication Effected Slot SIO TEST PASSED A2 SIO TEST FAILED Quad SIO A4 SIO TEST FAILED A6 SIO TEST FAILED PIO TEST PASSED PIO TEST FAILED Standby CPU ERR TEST PASSED...
  • Page 83 Section 060-INDP-111 System Description 2-55 Table 2-14 Standby Processor TEST Command Functions and Availability Test Pass Test Error Indication Indication Effected Slot CLK TEST PASSED CLK TEST FAILED CTC TEST PASSED EC-IC-ALM SIO TEST PASSED A2 SIO TEST FAILED Quad SIO A4 SIO TEST FAILED A6 SIO TEST FAILED PIO TEST PASSED...
  • Page 84: Test Descriptions

    2-56 Section 060-INDP-111 System Description Table 2-15 Test Descriptions Test Name Mnemonic Occurrence Tested DPR Communications SCSI Every hour, 50 minutes after (standby processor) the hour Disk File System End-to-End SCSI 3:10 am Integrity (active processor) TEC/DSI Communications B0 TEC/DSI TEC/DSI1 Every 20 minutes* TEC/DSI Communications...
  • Page 85: Dpr Communication Test

    Section 060-INDP-111 System Description 2-57 DPR Communication Test The DPR is shared by the main CPU and the SCSI Interface PCA. This 32K RAM is divided into sixteen descriptors and 16 buffers. The buffers are further divided into three types: •...
  • Page 86: Tec/Dsi Communication

    2-58 Section 060-INDP-111 System Description The Disk Write/Read test confirms that data can be written to and read from disk. There are two functional tests involved. The first test is the 4K buffers test, then the 512 byte buffers test. Table 2-16 Disk Write/Read Functions Overview For Writing to Disk...
  • Page 87: Ram Write-Read-Verify Test

    Section 060-INDP-111 System Description 2-59 Bx TEC TEST PASSED where: x - TEC/DSI Port ID (0 or 2) 0 - message is from the TEC/DSI PCA in slot A13 2 - message is from the TEC/DSI PCA in slot A12. The running test performs the same tests as the manual test, but asks for the status of the first TEC/DSI PCA on the 5, 25, and 45 minute boundaries, and the status of the second TEC/DSI PCA on the 15, 35, and 55 minute...
  • Page 88 2-60 Section 060-INDP-111 System Description The ECAC initiates a Processor switch when the current error count in the active Processor exceeds sixteen (16), generates the appropriate alarm, and outputs the following error message to the terminal; refer to the procedure for this message and perform the craftsperson activities listed: MP SWITCH The ECAC Communication test checks the communication between the...
  • Page 89: Ctc Vector Test

    Section 060-INDP-111 System Description 2-61 CTC Vector Test The CTC channels are used as countdown timers and these timers generate Processor interrupts. When an interrupt occurs, the CTC counter for the channel is set to a "1" (one). After the interrupt is processed, the counter is set to "0"...
  • Page 90: Dma Communication Test

    2-62 Section 060-INDP-111 System Description where: xx - A2 - Communications port; Modem/HOC (download) link. - A4 - Maintenance port; BMC is unable to obtain a Switching System prompt from the Maintenance Interface printer port (Terminal 2 for DMS-100;SDI port for DMS-10). - A6 - Maintenance port;...
  • Page 91: Communication Processor (Cp) Testing Overview

    Section 060-INDP-111 System Description 2-63 receiver. Upon completion of transmission, the transmitter generates an interrupt to the receiver to give control to the receiver, and to start receiver completion. The receiver accepts all of the incoming bytes, echoes them, and waits for the transmitter interrupt, to begin its completion.
  • Page 92 2-64 Section 060-INDP-111 System Description The CP test function can be invoked manually by either of two means. The first is automatic activation by the BMC during a cold or warm restart (CP reset) procedure to automatically ascertain proper system operation. The CP test function can also be invoked by manual input at a local terminal.
  • Page 93 Section 060-INDP-111 System Description 2-65 CP PRG Checksum Test Failed CP DMA Test Tests the DMA registers to detect DMA failures and DMA false interrupts. The test checks the DMA registers to determine whether, or not, a DMA operation was successful. If the test is successful, in background mode, there is no output.
  • Page 94: Error Indicators

    2-66 Section 060-INDP-111 System Description Error Indicators This section describes the error indication structure for the BMC. Three Level Alarm Structure The ECAC provides three alarm categories. The categories are defined, in order of severity as: CRITICAL (CRIT), MAJOR (MAJ), MINOR (MIN), with NO ALARM defined as the error free (redundant system) operational level.
  • Page 95: Error Map (Errmap) Command

    Section 060-INDP-111 System Description 2-67 • A MAJOR alarm occurs in each Processor, the alarm is reported as CRITICAL. • A MAJOR alarm occurs in one Processor, and a MINOR alarm occurs in the other Processor, the alarm is reported as MAJOR. •...
  • Page 96 2-68 Section 060-INDP-111 System Description CURRENT ALARM ASSIGNMENTS ARE: DEV/EVT # NAME ALARM LEVEL * 01 NO BLK LAST PER MINOR 02 TEC STNBY FAIL MINOR 03 TEC PRIME FAIL MAJOR * 04 D-RAM ERROR MAJOR 33 DISK ER MESSAGE MINOR * INDICATES CURRENTLY ACTIVE ALARM(S) TO CHANGE ERRMAP TABLE, ENTER: ERRMAP DEV/EVT# ALARMTYPE LEVEL...
  • Page 97: Log Call Record File

    Section 060-INDP-111 System Description 2-69 where: event# - Device/Event Number (0-99) level - Severity Level (0-3), 3 - most serious. If desired, make the inhibited alarms permanent by entering the following at the maintenance terminal (after the completion of the ERRMAP command entry activity): >SITDAT WRITE (cr) Alarms (ERRMAP entries) on the Standby Processor are viewed and...
  • Page 98: System Description - Software

    2-70 Section 060-INDP-111 System Description System Description - Software The BMC is an intelligent peripheral of the associated Switching System, capable of making decisions without guidance from the Switching System’s Common Control Processor/Memory Complex. The BMC activities are controlled by software resident in the BMC. The internal architecture of the BMC is closely related to the task structure of the software modules.
  • Page 99: Application Routines

    Section 060-INDP-111 System Description 2-71 combined with a strong intercoupling of function modules. The BMC start- up and scheduler consists of six modules: • Process Scheduler • Clock Services • System Calls • Memory Manager • General Purpose Functions • Human-machine interface functions.
  • Page 100: Interface Routines

    2-72 Section 060-INDP-111 System Description are provided to convert the raw data to the required format before processing any further. Other application routines manage events that must be scheduled on a regular basis. Call record report generation and BMC processor switchovers are two examples of the events directed by these application modules.
  • Page 101: Downloading Software To The Bmc

    Downloading software to the BMC When a situation arises where the BMC requires a download of software, it is normally accomplished by transfer from an authorized source, usually Nortel. There are two possible BMC conditions that require the downloading of new software.
  • Page 102: Data Storage

    2-74 Section 060-INDP-111 System Description Validated call records are loaded into a disk buffer on the SCSI Interface PCA, used for AMA call records. When a buffer is full, its contents are written to disk, while another buffer is made available to receive call records. Ribbon cables are used to send data and write commands from the SCSI Interface PCA to the SCSI Crossover PCA and both disk drives.
  • Page 103: Data Management

    Section 060-INDP-111 System Description 2-75 command. For more information concerning the LSTDIR command, consult the Commands and Messages Guide section. The total number of files divides into two categories: dynamic and static. Dynamic files are usually large, while most static files are small. Most dynamic files are data files consisting of AMA and log (LOG) records.
  • Page 104: Block Types

    2-76 Section 060-INDP-111 System Description Generally, call record data blocks from the Switching System are formatted as LSSGR data blocks. Other files on disk contain the site data and statistics. An Error Block is generated and used during file transfer to the HOC to indicate that a data block could not be successfully read from the storage device.
  • Page 105: Disk Capacity Indications Requiring Maintenance Activity

    Section 060-INDP-111 System Description 2-77 message journal files and secondary (polled) call record data files. The number is entered into the file upon creation of the file on the disk. After the file has been polled, the number is decremented by one at 1 a.m. of each day. The file is deleted when: •...
  • Page 106 2-78 Section 060-INDP-111 System Description signal is sent to the Switching System. The Switching System attempts to access the second interface. The second interface also returns an EOT to the Switching System and a critical alarm is generated. When the allocated disk space for AMA files is reached, the following actions occur: 1.
  • Page 107: Bad Track Mapping

    Section 060-INDP-111 System Description 2-79 In the extreme case, where the second disk reaches 100 percent usage, the following activities occur: 1. Alarm level is raised to critical. 2. BMC returns EOT status to the Switching System. 3. Switching System transfers to the second interface. 4.
  • Page 108: Communications

    2-80 Section 060-INDP-111 System Description octets, the relative file sizes are: (a) 325 blocks at 9600 bits-per-second (baud) and, (b) 40 blocks at 1200 baud. The headers and trailers are generated and maintained by the BMC. Other files handled by the BMC include: statistical, error, communication, and security files.
  • Page 109: Bisync Station Modes

    Section 060-INDP-111 System Description 2-81 There are basically two types of messages in the BISYNC protocol: Text and Control. Control messages are used to administer the link. These messages are also referred to as "overhead." Text messages contain the information that the application programs exchange.
  • Page 110: Message Transmission

    2-82 Section 060-INDP-111 System Description • EOT - used to indicate the end of application information. • Acknowledge (ACKn - n = 0 or 1) - used to accept the last message received. The ACK0 and ACK1 messages are generally alternated. •...
  • Page 111 Section 060-INDP-111 System Description 2-83 • ACK0 message - sent in response to an ENQ message after entering Listener mode. • NAK message - sent in response to an ENQ message if the station is unable to enter Listener mode. Both stations, while in Contention mode, can attempt to enter Talker mode by sending an ENQ message.
  • Page 112: Structure Identifier

    2-84 Section 060-INDP-111 System Description • NAK message - indicates an unsuccessful reception of the last Text message. A re-transmission of that message is required. • RVI message - indicates successful reception of the last Text message plus a request to enter the Talker mode. The station in Talker mode should finish sending Text messages and then send an EOT message.
  • Page 113: Download Of Software

    The download of new software uses ASCII asynchronous communications protocol. Nortel maintains a record of software for each operating site. A port on the BMC is dedicated to the download function. Software may be downloaded to the BMC because: •...
  • Page 114: Fixed Data Test Pattern

    2-86 Section 060-INDP-111 System Description File is received. The loop can be repeated a maximum of one thousand times per request, depending on the capabilities of the equipment at the HOC. A cancel command at the HOC terminal can be used to terminate Test File loop activity.
  • Page 115: Statistical Reports

    Section 060-INDP-111 System Description 2-87 Statistical Reports The Statistics Report(s) provide information concerning the current day's and one previous day's AMA, COM, and DISK activity. The format of the statistical reports are shown below. Enter the following at the maintenance terminal to obtain this report: >REPORT Reptype Repperiod (cr) where: Reptype - AMA (AMA report), COM (polling summary), or...
  • Page 116 2-88 Section 060-INDP-111 System Description Note 9: If this report is requested while the disk system is in AO or BO, the report column for off-line disk contains the characters N/A for VENDOR ID, PRODUCT ID, REVISION LEVEL, DISK CAPACITY, USER CAPACITY, MANUFACTURE DEFECTS, and GROWN DEFECTS.
  • Page 117: Optional Functions

    Section 060-INDP-111 System Description 2-89 Optional Functions This section describes the functions that are optional for the DMS-10 and DMS-100 Switching Systems. Multiple Terminals Multiple terminals can be attached to the BMC. Terminals can be attached directly or may be routed through the Switching System to a port which is attached to the BMC.
  • Page 119: General Information

    Section 060-INDP-310 System Administration Guide General Information The purpose of this section is to present general information concerning assignment of site-dependent data, system parameters, files management and security related issues for the BMC. This section provides examples for use in the definition of system requirements. System administration consists of review and definition of the operating characteristics of the BMC.
  • Page 120: System Administration

    3-2 Section 060-INDP-310 System Administration Guide • Receipt and storage of call record data • Polling of call record data by the HOC. Each of these functions has specific requirements that differ from other tasks. The differences in operating requirements of each of these tasks defines a level of operation.
  • Page 121: Machine-Machine Interface

    Section 060-INDP-310 System Administration Guide 3-3 Machine-Machine Interface The BMC provides interface for the Switching System and the HOC. The Switching System transmits call record data to the BMC. The HOC polls call records from the BMC through one of two serial ports. Modems attached to the serial ports provide a physical link to other computing systems.
  • Page 122: Command Abort Sequence

    3-4 Section 060-INDP-310 System Administration Guide TECMAINT>CTRL/Z Command Abort Sequence Any terminal keyboard entry can be aborted before the carriage return with a CONTROL Z (CTRL/Z). A CRTL/Z is entered by pressing and holding the Control key and pressing the Z key. No carriage return is required. The BMC (terminal) skips to the next line and is ready for command input.
  • Page 123: Initial System Start-Up

    Section 060-INDP-310 System Administration Guide 3-5 CAUTION To avoid conflict of data on the BMC disk drives, do not use the SITDAT WRITE command when the user interface is directed to the standby processor. The input form of this command is: >SITDAT WRITE (cr) The BMC responds: (log message) SITDAT FILE DISK JOB COMPLETE...
  • Page 124: Site Data Entry

    3-6 Section 060-INDP-310 System Administration Guide • CP INTERFACE - defines the type of interface used in polling for a specific link. • ERRMAP - defines the type, level and handling of alarms. • LPAD - defines the leading pad character for the polling communications link.
  • Page 125 Section 060-INDP-310 System Administration Guide 3-7 Note 5: For full-time block checks, enter 00 for Start, and 23 for Stop, and 01 for Interval. Note 6: If no block checks are required, enter 00 for start and 00 for Stop, and 00 for Interval. The system response is as follows: BLOCK CHECK START xx END yy HOURS, INTERVAL OF zz MINUTES where: xx - block check start time (hour of the day)
  • Page 126 3-8 Section 060-INDP-310 System Administration Guide where: link - one digit link number, either 1 or 2 rate - baud rate (select one of the following values: 1200, 2400, 4800, or 9600). Note 9: The BMC BISYNC system can use the either the RS-232 or V.35 interface for an maximum baud rate of 9600.
  • Page 127 Section 060-INDP-310 System Administration Guide 3-9 BMC truncates the frame size to the nearest 32 byte increment. The BMC prints the truncated frame size. Billing Validation Identification Command The Billing Validation Identification (BVALID) command is used to examine or change the site information for the Switching System to which the BMC is connected.
  • Page 128 3-10 Section 060-INDP-310 System Administration Guide command was entered to generate its own transmit clock. EXTERNAL - BMC uses an external device for its clock source. To change the CP clock source, enter the following at the maintenance terminal: >CP CLOCK link source (cr) where: link - one digit link number;...
  • Page 129 Section 060-INDP-310 System Administration Guide 3-11 To change the polling modem line control setting, enter the following at the maintenance terminal: >CP CONTROL type (cr) where: type - modem line control type (HD or FD). The system responds with the following message: LINE CONTROL SET TO xxxx DUPLEX Note: Follow this command with the SITDAT WRITE and LINIT commands to make the change permanent and transfer the data to the CP.
  • Page 130 3-12 Section 060-INDP-310 System Administration Guide Note: Follow this command with the SITDAT WRITE and LINIT command to make the change permanent and transfer the data to the CP. Alarm Handling Activity The ERRMAP command is used to list or assign all the alarm type, status and level assignments.
  • Page 131: Errmap Entries To Log Message Cross-Reference

    Section 060-INDP-310 System Administration Guide 3-13 disk mode (PRIME to ONLY). Less serious errors do not require such actions. Table 3-1 is a cross reference between the BMC output log messages and the ERRMAP entry messages. Table 3-1 ERRMAP entries to Log message cross-reference EVT# Message, alarm, level Associated log message(s)
  • Page 132 3-14 Section 060-INDP-310 System Administration Guide Table 3-1 ERRMAP entries to Log message cross-reference EVT# Message, alarm, level Associated log message(s) TEC DATA OVRFLO, Critical, 0 DATA BUFFER EXCEEDED TEC BUFFER OVERFLOW xx BLOCKS NO CLK TIME SET, Minor, 0 KEY “SETCLK”, THEN ENTER DATE, TIME, AND PLANNED SWITCH, PSwitch, 0 MP SWITCH...
  • Page 133 Section 060-INDP-310 System Administration Guide 3-15 Table 3-1 ERRMAP entries to Log message cross-reference EVT# Message, alarm, level Associated log message(s) SITE FILE ERROR, Minor, 0 SITDAT FILE yyyyyy ERROR: ee STAT FILE ERROR, Minor, 0 TDYSTS FILE yyyyyy ERROR: ee EXCESS INV BLKS, Minor, 0 BLOCK LENGTH ERROR DETECTED BLOCK PARITY ERROR DETECTED...
  • Page 134 3-16 Section 060-INDP-310 System Administration Guide Table 3-1 ERRMAP entries to Log message cross-reference EVT# Message, alarm, level Associated log message(s) CP FAULT, Major, 1 BOOTCP FILE yyyyyy ERROR: ee CP ACTIVATE FAIL CP AUDIT FAIL CP BOOT LIST EMPTY CP DATA ERR CP DMA Test Failed CP I/O FAILURE...
  • Page 135 Section 060-INDP-310 System Administration Guide 3-17 Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 01, NO BLK LAST PER Cause:BMC has not received any data blocks from the Switching Minor, 0 System within a desired period of time Test:every 60 minutes (as defined by AMAHRS entry) Reset:no automatic reset, cleared by input of RSERR command Notes:no check is performed if the current time is not within the...
  • Page 136: Description Of Errmap Entries

    3-18 Section 060-INDP-310 System Administration Guide Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 04, D-RAM ERROR Cause:parity error of DRAM Major, 1 Test:by Memory Expansion PCA when parity error occurs (detected) whenever reading a byte from RAM Reset:no automatic reset, cleared by input of RSERR command Notes:alarm set and message printed only once per occurrence 05, SIO-1 FAILURE...
  • Page 137 Section 060-INDP-310 System Administration Guide 3-19 Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 08, DMA COMM FAIL Cause:DMA timeout Major, 2 Test:checked every 16 msecs Reset:no automatic reset, cleared by input of RSERR command Notes:when the TEC/DSI PCA transfers call record blocks through the DMA channel, BMC sets up a time out value.
  • Page 138 3-20 Section 060-INDP-310 System Administration Guide Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 11, TEC DATA OVERFLO Cause:input data buffer overflow when disk storage process is Critical, 0 overloaded Test:buffer check on the input block ready for processing. Error is detected when no more buffers are available Reset:RSERR input clears alarm;...
  • Page 139 Section 060-INDP-310 System Administration Guide 3-21 Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 14, ONLY NON-REDUND Reset:a.only by changing the processor mode to redundant Minor, 0 (PRIME) mode b.RSERR command does not clear this alarm Notes:set only if the processor is an Active Processor 15, STNBY COMM DOWN Cause:failure of PIO communications to the Standby Processor Major, 0...
  • Page 140 3-22 Section 060-INDP-310 System Administration Guide Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 17, DSK 70% PRIMARY Cause:disk usage has exceeded 70% of available disk space Minor, 0 Test:on every minute boundary Reset:RSERR input command clears the alarm; alarm is set at the next minute if the disk usage is greater than 70% Notes:a.not checked and set if the disk usage is greater than 90%;...
  • Page 141 Section 060-INDP-310 System Administration Guide 3-23 Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 20, DSK STORE LIMIT Cause:a.both disks are full Critical, 0 b.number of versions of a file type (AMA or LOG) has reached 255 Test:on every minute boundary Reset:enter RSERR command to clear alarm;...
  • Page 142 3-24 Section 060-INDP-310 System Administration Guide Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 23, NO INDEX FILE Cause:index file open fail or index file not found Major, 0 Test:no periodic check; tested when trying to open, delete, or update the index file Reset:RSERR command clears alarm Notes:alarm and message set and printed whenever error occurs...
  • Page 143 Section 060-INDP-310 System Administration Guide 3-25 Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 27, EXCESS INV BLKS Cause:receipt of number of invalid blocks greater than specified Minor, 0 invalid block limit Test:performed whenever a call record block is received (there is no periodic check) Reset:no automatic reset, alarm is cleared by input of RSERR command...
  • Page 144 3-26 Section 060-INDP-310 System Administration Guide Table 3-2 Description of ERRMAP Entries EVT#, message, alarm, level Comments 31, DISK MODE ALARM Cause:by change of disk mode from PRIME to ONLY Major, 0 Test:a.disk mode check at minute boundary, if disk is found to be in ONLY mode, alarm is set b.execute DISK MODE command to change disk mode to ONLY mode...
  • Page 145 Section 060-INDP-310 System Administration Guide 3-27 The system responds as shown below. CURRENT ALARM ASSIGNMENTS ARE: DEV/EVT# NAME ALARM LEVEL * 01 NO BLK LAST PER MINOR TEC STNBY FAIL MINOR TEC PRIME FAIL MAJOR * 04 D-RAM ERROR MAJOR DISK ER MESSAGE MINOR * INDICATES CURRENTLY ACTIVE ALARM(S) TO CHANGE ERRMAP TABLE, ENTER:...
  • Page 146 3-28 Section 060-INDP-310 System Administration Guide 2 - If the standby alarm is less than 2 and the active alarm is 2, switch processors. 3 - If the standby alarm is less than 3 and the active alarm is 3, switch processors. Note 13: To clear an active alarm after the condition is no longer present, enter RSERR and 00 to reset all alarms, or DEVICE/EVENT# (1 or 2 digits) to clear a specific alarm.
  • Page 147: System Security

    Section 060-INDP-310 System Administration Guide 3-29 The system responds with the following message: AMA INVALID ALARM THRESHOLD - nnnnn where: nnnnn - number of invalid data items before an alarm is generated. To examine or change the number of AMA blocks required to automatically close the AMA at the start of polling: 1.Enter the following command at the terminal to change the number of AMA blocks required (default is 200):...
  • Page 148: Priorities

    3-30 Section 060-INDP-310 System Administration Guide The default password is USER.1 for the BMC. Passwords are controlled by the PSWD command. CAUTION It is recommended that the default password be changed after entry of system parameters to restrict access. Priorities Priorities are limiters which are placed on users and commands to control use of the system and the commands.
  • Page 149 Section 060-INDP-310 System Administration Guide 3-31 Table 3-3 BMC commands Command Description Priority Display BMC system time Locked at priority 1 CLRSTATS Clears today's statistics files Mainly System Administration, Maintenance (record may be lost) may require access (Priority 2) CLSACT Close specified file to further Mainly System Administration, Maintenance writes...
  • Page 150 3-32 Section 060-INDP-310 System Administration Guide Table 3-3 BMC commands Command Description Priority LNKDSC Disconnects active Mainly maintenance (Priority 2) communication link for five seconds (Drops DTR) LSTACT List active files General activity (Priority 1) LSTDIR List BMC files General activity (priority 1) MPRI Set command priorities Mainly System Administration, Maintenance...
  • Page 151: Machine-Machine Security Data

    Section 060-INDP-310 System Administration Guide 3-33 Table 3-3 BMC commands Command Description Priority TEST Test major BMC functions Mainly maintenance (Priority 2) VALPARM Set number of cumulative invalid Mainly System Administration, Maintenance data items before error may require access (Priority 2) Examine BMC operating program General activity (priority 1) version...
  • Page 152: Human-Machine Security

    3-34 Section 060-INDP-310 System Administration Guide To change the remote password, enter the following at the maintenance terminal: >KYWD nC keywrd (cr) where: n - remote station number (usually 1). keywrd - six alphanumeric characters used to identify the remote station.
  • Page 153: Command Priorities

    Section 060-INDP-310 System Administration Guide 3-35 The system responds as shown below: USR PASWRD --- ------ 01 PSWRD1 02 PSWRD2 03 PSWRD3 04 PSWRD4 Note 15: The output shown is for example purposes only. To change a password (same or lower priority level), enter the following at the maintenance terminal: PSWD>nC paswrd p (cr) where:...
  • Page 154: Automatic Logoff

    The four groups are: System Administration (priority 3), Maintenance (priority 2), General Use (priority 1), and Nortel field service personnel only (Priority 3). Note 19: Priorities of firmware commands (i.e., DISK and DOS) cannot be modified.
  • Page 155: Recovery From Lost Passwords

    Section 060-INDP-310 System Administration Guide 3-37 TERMINAL TIME-OUT - xxx where: xxx - terminal time-out value in minutes. To set the value for the terminal time-out, enter the following at the maintenance terminal: >SETTERM TIMEOUT nnn (cr) where: nnn - minutes before a logoff (1 to 120). The system responds as shown below: TERMINAL TIME-OUT - xxx To disable the auto log-off function, enter the following at the maintenance...
  • Page 156 3-38 Section 060-INDP-310 System Administration Guide To log off the system, enter the following at the maintenance terminal: >BYE (cr) The system responds as shown below: (log message) USER x LOGGED OUT where: x - user number. 297-6201-502 Standard 01.02 September 2000...
  • Page 157 Section 060-INDP-310 System Administration Guide 3-39 Figure 3-1 System Administration Site Data Worksheet - Sheet 1 of 3 Office Identification and Switching System Type (BVALID) Time to confirm call record blocks are being received from (00-23) the Switching System (AMAHRS) Start hour End hour (00-23)
  • Page 158 3-40 Section 060-INDP-310 System Administration Guide Figure 3-1 System Administration Site Data Worksheet - Sheet 2 of 3 Command Priorities Description Command Priority Set call record confirm receipt time AMAHRS Set polling link baud rate BAUD Set polling Frame Buffer Size BUFSZ Set Site Dependent Data BVALID...
  • Page 159 Section 060-INDP-310 System Administration Guide 3-41 Figure 3-1 System Administration Site Data Worksheet - Sheet 3 of 3 Error Alarm Handling Alarm Name Level Notes CRIT INHIB 01 NO BLK LAST PER 02 TEC STNBY FAIL 03 TEC PRIME FAIL 04 D_RAM ERROR 05 SIO-1 FAILURE 06 ERROR CTL CONFL...
  • Page 161: Human-Machine Interface

    Section 060-INDP-410 Command and Message Guide This document lists and defines the BMC commands and major messages. General command, syntax and, human-machine interface requirements are listed first. Major procedures are discussed in functional groups. Commands and messages are discussed in greater detail in separate paragraphs. Tables are included that summarize and list commands and messages both functionally and alphabetically.
  • Page 162: Prompts

    4-2 Section 060-INDP-410 Command and Message Guide the same or lower level priority. Any attempt to access commands of higher priority results in an ILLEGAL COMMAND or PRIVILEGED COMMAND response. The user level, the command priorities, and how to set priorities is discussed in the System Administration Guide section.
  • Page 163: Errmap

    Section 060-INDP-410 Command and Message Guide 4-3 • Polling link adjustment commands • Processor activity command • Read/write operation commands • Security commands • Site data entry commands • Software version command • Statistics commands • System clock commands • TEC/DSI commands •...
  • Page 164: Errmap Subcommands

    4-4 Section 060-INDP-410 Command and Message Guide Table 4-1 ERRMAP subcommands Subcommand Description ERRMAP Displays a list of alarms, their current level assignments, and indicates whether they are currently asserted for the active BMC processor. ERRMAP event alarm Changes the alarm type and/or alarm level for a specified device or level event number on the active BMC processor.
  • Page 165: Alarm Type Descriptions

    Section 060-INDP-410 Command and Message Guide 4-5 Table 4-2 Alarm type descriptions Alarm_typ Description INHIBIT Indicates a particular alarm has been deactivated for printout and reporting purposes; the error message prints out, but the alarm is not set. The condition still exists;...
  • Page 166: Alarm Level Descriptions

    4-6 Section 060-INDP-410 Command and Message Guide Table 4-3 Alarm level descriptions Description A moderately serious fault. If the standby processor alarm level is less than 2, a processor switch occurs. The most serious fault. If the standby processor alarm level is less than 3, a processor switch occurs.
  • Page 167 Section 060-INDP-410 Command and Message Guide 4-7 The following table lists the valid device/event names for the all of the BMC systems. Table 4-4 ERRMAP device/event names Event Event name Alarm Level NO BLK LAST PER Minor TEC STNBY FAIL Minor TEC PRIME FAIL Major...
  • Page 168 4-8 Section 060-INDP-410 Command and Message Guide Table 4-4 ERRMAP device/event names Event Event name Alarm Level OFFLIN DSK FULL Major DSK STORE LIMIT Critical DISK WRITE FAIL Major DSK INDEX ERROR Minor NO INDEX FILE Major DIRECTORY FULL Critical SITE FILE ERROR Minor STAT FILE ERROR...
  • Page 169 Section 060-INDP-410 Command and Message Guide 4-9 In order to INHIBIT a selected alarm for the active processor, enter the following command: >ERRMAP event INHIBIT 0 (cr) To view or retire active alarms on standby processor, enter the following command: >DOS S ERRMAP (cr) The system responds by displaying the current BMC alarm status and assignments for the standby processor.
  • Page 170: Command Execution Control Command

    4-10 Section 060-INDP-410 Command and Message Guide ALARM CLEARED To clear active alarms on the standby processor (alarms clear if no fault condition exists), enter the following command: >DOS S RSERR event (cr) The system responds by displaying the following message: ALARM CLEARED Command execution control command The command execution control command, as listed below, allows a...
  • Page 171 Section 060-INDP-410 Command and Message Guide 4-11 • CP LOOP ACT • CP LOOP STDBY • CP MEMWRITE • CP TEST ACT • CP TEST STDBY • CP VS ACT • CP VS STDBY. CP BOOT ACT CP BOOT ACT, a maintenance command, allows the user to direct the BMC to reload the CP on the active processor by sending it the files listed in the file BOOTCP.
  • Page 172 4-12 Section 060-INDP-410 Command and Message Guide filename- six character load file name version- 1 to 2 digit numeric file version number (range: 1-99; version 0 is not allowed). The list of file names and version stored in the file BOOTCP is displayed. The new one should appear at the end of the list.
  • Page 173: Cp Clock

    Section 060-INDP-410 Command and Message Guide 4-13 Example of command usage To load the contents of the BOOTCP file to the standby CP, issue the following command: >CP BOOT STDBY (cr) The system responds with the following: CP RESTART CP RELOAD CP RESTART CP ACTIVE where:...
  • Page 174: Cp Control

    4-14 Section 060-INDP-410 Command and Message Guide link - one digit link number, either 1 or 2 source - clock source, INTERNAL or EXTERNAL. The system displays clock source data for the specified link. LINK# 0x: CLK SRC= yyyyyyyy where: x - link - one digit link number, either 1 or 2.
  • Page 175: Cp Examine

    Section 060-INDP-410 Command and Message Guide 4-15 >CP CONTROL xx (cr) where: xx - modem line control type; HD - Half Duplex or FD - Full Duplex. The system responds as follows: LINE CONTROL SET TO xxxx DUPLEX Note: Follow this command with the SITDAT WRITE and LINIT commands to make the change permanent and update the CP with the new values.
  • Page 176: Cp Loop Act And Cp Loop Stdby

    4-16 Section 060-INDP-410 Command and Message Guide Examples of command usage To examine the CP INTERFACE currently assigned, issue the following command: >CP INTERFACE (cr) The system displays the interface data for the polling links: LINK xx, INTERFACE = yyyy where: xx- one digit link number, either 1 or 2 yyyy- interface used (RS232 or V35).
  • Page 177: Cp Memwrite

    Section 060-INDP-410 Command and Message Guide 4-17 There will be one of two responses from the system. If the test passes, the system displays the following: CP LOOP TEST PASSED If the test fails, the system displays the following: LOOP_BACK TEST NOT ACCEPTED To perform the loop test on the CP for the standby processor, use the following command: >CP LOOP STDBY (cr)
  • Page 178: Cp Test Stdby And Cp Test Act

    4-18 Section 060-INDP-410 Command and Message Guide CP_MMI_TSK - Memory Write Completed CP TEST STDBY and CP TEST ACT CP TEST ACT and CP TEST STDBY, both maintenance commands, enable the user to request a series of tests be run on the active or standby CPs. Running these tests on both the active and standby processors simultaneously yields mingled responses.
  • Page 179: Craftsperson Assistance Command

    Section 060-INDP-410 Command and Message Guide 4-19 Example of command usage Issue the following command to request the firmware/software versions of the active CP: >CP VS ACT (cr) The system displays the firmware and software data in the following format: aaa-CPFbbb-cc dd ee-fff-gggg hh:ii:jj:mm CPS-6M9bbb-cc dd ee-fff-gggg hh:ii:jj:mm where:...
  • Page 180: Disk Operation Commands

    4-20 Section 060-INDP-410 Command and Message Guide BUFSZ BVAL KYWD LPAD SELGRP VALPARM IDXMAINT TECMAINT SYSUTIL SITDAT CLRSTATS SWACT ERRMAP RSERR VS AMAHRS LNKDSC LINIT CLSACT DELFILE LSTDIR DMPFILE LSTACT DMASTAT REPORT TECRAM BAUD TEST SETCLK TDIF MPRI PSWD SETTERM DPRTST RSCMD CP HELP The above commands are software-based commands only.
  • Page 181: Disk Format

    Section 060-INDP-410 Command and Message Guide 4-21 where: address- address to examine. Range: 0-FFFFF bytes- specifies the number of bytes to examine. Range: 1-99. CAUTION This command should only be used under the direct supervision of experienced support personnel. DISK FORMAT The DISK FORMAT command allows the user to format a selected disk drive.
  • Page 182: Disk Iowrite

    4-22 Section 060-INDP-410 Command and Message Guide where: port - I/O port address. Range: 0-FF. After the port contents are displayed, the system responds with the following message: OUTPUT COMPLETE DISK IOWRITE The DISK IOWRITE command writes data to the specified I/O disk processor port address.
  • Page 183: Disk Mode

    Section 060-INDP-410 Command and Message Guide 4-23 CAUTION 2 Improper use of this command may cause erroneous data to be written to a memory location that is actually in use by other data. Do not use this command without first contacting technical assistance personnel.
  • Page 184 4-24 Section 060-INDP-410 Command and Message Guide xxxx - current disk mode value. Table 4-6 defines the valid values. Table 4-6 Disk mode definitions Mode Description A Only - BMC processors read data from and write data to the disk in the A chassis ONLY.
  • Page 185 Section 060-INDP-410 Command and Message Guide 4-25 Table 4-7 Allowed disk mode changes Initial Final Change Remarks/Conditions Mode Mode Allowed Allowed if the B disk is initialized. System response: DISK BACKUP STARTED This mode change is used for specific DISK FULL recovery procedures only.
  • Page 186: Disk Restart

    4-26 Section 060-INDP-410 Command and Message Guide Table 4-7 Allowed disk mode changes Initial Final Change Remarks/Conditions Mode Mode Allowed This mode change is used for maintenance purposes only. Contact your next level of support if it is necessary to use this mode change.
  • Page 187: Disk Usage

    Section 060-INDP-410 Command and Message Guide 4-27 >DISK RESTART (cr) CAUTION Use of this command can cause loss of billing data. The system responds with the following messages: DISK MODE: xx GOOD LOGIDX FILE CP RESTART GOOD AMAIDX FILE DISK USAGE DISK USAGE displays the number of Allocation Units on the disk that have been used, compared to the total number available.
  • Page 188: Dma Commands

    4-28 Section 060-INDP-410 Command and Message Guide where: DKF- disk firmware mnemonic aaaa- Product Engineering Code (PEC) bb- release increment cc- checksum byte dd-eee-ffff- date of firmware creation (day-month-year) gg:hh:jj:kk- time of firmware creation (hour:minute:seconds:hundreth of seconds) filename- firmware filename. DMA commands The DMA commands are used to examine the data stored in the BMC RAM.
  • Page 189: File Index Manipulation Commands

    File index manipulation commands verify, examine, create, or edit index files that are created to keep track of files generated by the BMC and call records received from the Switching System or operating programs from the Nortel host. The file index manipulation commands are as follows: •...
  • Page 190: Idxmaint Check

    4-30 Section 060-INDP-410 Command and Message Guide • IDXMAINT DIR CLOSED • IDXMAINT DIR OPEN • IDXMAINT EXAMINE • IDXMAINT SUMMARY • SELGRP. Note 12: An Index file can only contain 200 closed files and 1 open file. There can be numbers from 1 to 255 in extreme circumstances. Note 13: Index files store all closed versions of a file type.
  • Page 191: Idxmaint Close

    Section 060-INDP-410 Command and Message Guide 4-31 IDXMAINT CLOSE The IDXMAINT CLOSE command closes the AMA or LOG file that is currently open for read. The file may have been opened by polling (AMA files) or the IDXMAINT EXAMINE command. Example of command usage To close any file that is open for reading, issue the following command: >IDXMAINT CLOSE (cr)
  • Page 192: Idxmaint Create File

    4-32 Section 060-INDP-410 Command and Message Guide Use the following command to create a new index file containing primary and secondary (polled) data: >IDXMAINT CREATE DIR file_type vers1 blk_num vers2 (cr) where: file_type- specifies file type; may be AMA or LOG. vers1- 3-digit decimal value;...
  • Page 193: Idxmaint Delete

    Section 060-INDP-410 Command and Message Guide 4-33 file_type - AMA or LOG. CAUTION Use of this command may cause loss of billing data. The following messages are displayed: file_type WRITE FILE CLOSED VS vvv: bbb BLKS, ddd aaaaaaa file_type SEQ# nnnnnn where: vvv- file version just closed bbb- number of data blocks contained in the file...
  • Page 194: Idxmaint Dir Open

    4-34 Section 060-INDP-410 Command and Message Guide Examples of command usage To print the status of closed call record, log, or exception data files, use the following command: >IDXMAINT DIR CLOSED file_type ver (cr) where: file_type- AMA or LOG ver- decimal number that specifies the number of file numbers requested.
  • Page 195: Idxmaint Examine

    Section 060-INDP-410 Command and Message Guide 4-35 VS vvv: bbb BLKS, dddd PRIMARY file_type SEQ# nnnnnn where: vvv- file version number bbb- number of data blocks currently contained in the file. dddd- number of primary blocks in the file. nnnnnn- first sequence number in the file. IDXMAINT EXAMINE The IDXMAINT EXAMINE command allows the user to examine selected blocks from the BMC disk.
  • Page 196 4-36 Section 060-INDP-410 Command and Message Guide The first 14 bytes are the block header. The rest of the block is AMA data records. The format of the block header is described in the following table. Table 4-10 Block header format Byte Description Byte 1-4...
  • Page 197: Idxmaint Summary

    Section 060-INDP-410 Command and Message Guide 4-37 where: num - specifies the number of blocks to be examined. Range: 1-255. Note 16: For the IDXMAINT EXAMINE file_type NEXT num command to be valid, it must immediately follow the IDXMAINT EXAMINE file_type format seq_no command. IDXMAINT SUMMARY IDXMAINT SUMMARY prints a summary of index files and oldest version with records to poll.
  • Page 198: Selgrp

    4-38 Section 060-INDP-410 Command and Message Guide SELGRP SELGRP allows the user to select a specific group of secondary data sequence numbers when sequence numbers have rolled over. The BISYNC protocol restarts sequence numbering at zero after 65,535. Note: The value of SELGRP affects any IDXMAINT commands that reference the sequence number (i.e., IDXMAINT EXAMINE).
  • Page 199: Clsact

    Section 060-INDP-410 Command and Message Guide 4-39 CLSACT CLSACT closes the specified active file. A closed file can no longer be written to, but it can be read. It is important that the file to be closed does not contain data that has to be retrieved. Use the LSTACT command to obtain a list of open files.
  • Page 200: Dmpfile

    4-40 Section 060-INDP-410 Command and Message Guide CAUTION Exercise care in deleting files. Do not delete billing records or the site data unless necessary. Examples of command usage To delete a file from the BMC system directory, issue the following command: >DELFILE name ver (cr) where:...
  • Page 201: Lstact

    Section 060-INDP-410 Command and Message Guide 4-41 >DMPFILE name ver start count (cr) where: name- specifies file name, up to six characters ver- specifies file version number. Range: 0-255 (0 is the latest version) start- specifies starting block. Range: 0-999,999 count- specific number of blocks to dump.
  • Page 202: Lstdir

    4-42 Section 060-INDP-410 Command and Message Guide Example of command usage To display a list of all currently open data files, enter the following command: >LSTACT (cr) The system displays the following message: FILE OPEN: aa bb cc ddddd ee files listed where: aa- ID number of the open file bb- status of the open file.
  • Page 203 Section 060-INDP-410 Command and Message Guide 4-43 where: ii- file ID (if file is open for write); 11 if closed for write nnnnnn- file name tt*- file type. Values: 00 (if file 4K buffered [8 sectors]) or 01 (if file is 0.5K buffered [1 sector]) tw**- file type - number of sectors read from disk or written to disk in a single operation.
  • Page 204: Polling Link Adjustment Commands

    4-44 Section 060-INDP-410 Command and Message Guide where: name- specifies the file name, up to six characters ver- specifies file version. Range: 0 and 1-255 (0 is the latest version). The system responds with a message in the same format as listed above in the description of the LSTDIR ACT command.
  • Page 205: Lnkdsc

    Section 060-INDP-410 Command and Message Guide 4-45 >LINIT (cr) The system responds with the following messages: LINK INITIALIZED CP RESTART CP ACTIVE LNKDSC LNKDSC is a maintenance command that initializes the data areas used for the collection of incoming frames from the incoming polling link; causes the DTR on the active link to drop for five seconds, which disconnects the link.
  • Page 206: Swact Force

    4-46 Section 060-INDP-410 Command and Message Guide Example of command usage To initiate a processor activity switch from the active processor to the standby processor, issue the following command: >SWACT (cr) The system displays the following messages (order may vary): MP SWITCH DISK MODE: xP SITDAT FILE DISK JOB COMPLETE...
  • Page 207: Sysutil Examine

    Section 060-INDP-410 Command and Message Guide 4-47 • SYSUTIL EXAMINE • SYSUTIL IOREAD • SYSUTIL IOWRITE • SYSUTIL MEMWRITE. SYSUTIL EXAMINE The SYSUTIL EXAMINE command allows the user to examine the data at a specified address. The subcommands and related parameters for this command are listed in the following table.
  • Page 208 4-48 Section 060-INDP-410 Command and Message Guide CAUTION 2 Improper use of this command may result in an attempt to write data to a non-existent memory location, or, cause erroneous data to be written to a memory location that is already in use by other data.
  • Page 209 Section 060-INDP-410 Command and Message Guide 4-49 xx - data byte read from specified port. SYSUTIL IOWRITE SYSUTIL IOWRITE writes data to a specified I/O port. Example of command usage To write data to a specified I/O port, use the following command: >SYSUTIL IOWRITE port data (cr) where: port- specifies the port.
  • Page 210: Security Commands

    4-50 Section 060-INDP-410 Command and Message Guide >SYSUTIL MEMWRITE D page addr nlines (cr) where: page- specifies page in memory. Range: 0 and 2-7. addr- specifies the address. Range: 0-FFFF. datalist- string of hexadecimal data elements. There is a limit of 16 data elements.
  • Page 211: Login

    Section 060-INDP-410 Command and Message Guide 4-51 • LOGIN • MPRI • PSWD • SETTERM. LOGIN Individual users input a valid password to log into the BMC and the operating programs. This password is entered at the beginning of a maintenance session.
  • Page 212 4-52 Section 060-INDP-410 Command and Message Guide MPRI MPRI is used to assign or examine the priority level of a command. The priority level is used to control access to the use of a command. The MPRI subcommands are described in the following table: Table 4-15 MPRI subcommands Subcommand...
  • Page 213 Section 060-INDP-410 Command and Message Guide 4-53 >MPRI E cmd (cr) The system responds with the following message: COMMAND PRIORITY IS x PSWD PSWD is used to examine or assign the ten user passwords. These passwords control access to the BMC and associated commands. The password has a priority level that relates to the priority of individual commands.
  • Page 214 4-54 Section 060-INDP-410 Command and Message Guide To change a currently assigned password or assign a new priority level to that password, enter the following at the maintenance terminal: >PSWD nC paswrd p (cr) where: n -user number (0-9). To delete a specific user's password and priority level from the password table, enter the following at the maintenance terminal: >PSWD nD (cr) where:...
  • Page 215: Site Data Entry Commands

    Section 060-INDP-410 Command and Message Guide 4-55 xxx - terminal time-out value in minutes. To set the value for the terminal time-out, enter the following at the maintenance terminal: >SETTERM TIMEOUT xxx (cr) where: xxx - minutes before a logoff. Range: 1-120. The system responds with the following message: TERMINAL TIME-OUT = xxx To disable the auto log-off function, enter the following at the maintenance...
  • Page 216: Lpad

    4-56 Section 060-INDP-410 Command and Message Guide • LPAD • SITDAT • VALPARM BLOCKS • VALPARM INVALID. AMAHRS AMAHRS is a Site Data command used to display or set the time interval to verify that AMA records have been received from the Switching System. The command requires the start and end times to perform the check and the amount of time that can pass before an alarm is generated if no blocks are received.
  • Page 217 Section 060-INDP-410 Command and Message Guide 4-57 BAUD BAUD is used to examine or change the polling baud rate for a specific polling link. This baud rate is only used when the BMC is running on its internal clock. Examples of command usage To examine the BAUD rate(s) currently assigned, enter the following command: >BAUD (cr)
  • Page 218 4-58 Section 060-INDP-410 Command and Message Guide BUFSZ The Buffer Size (BUFSZ) command is used to set or examine the number of bytes in the messages sent to the HOC. The size may be from 64 bytes (minimum) to 512 bytes (maximum) in 32 byte increments (64, 96, 128... 512).
  • Page 219 Section 060-INDP-410 Command and Message Guide 4-59 KYWD The KYWD command is used to examine or set the machine-machine security keyword that uniquely identifies the HOC as a device that is authorized to access the BMC. A remote device must supply the keyword before access is permitted.
  • Page 220 4-60 Section 060-INDP-410 Command and Message Guide SITDAT The SITDAT command examines and updates the site data in the BMC. The subcommands for SITDAT are listed in the following table. Table 4-17 SITDAT subcommands Subcommand Description READ Reads (restores) site data parameters from BMC disk and overwrites site data stored in main memory (RAM).
  • Page 221 Section 060-INDP-410 Command and Message Guide 4-61 Note 14: Each hour, the BMC updates the site data in RAM from disk. Site data stored on disk is copied to RAM every hour. If any site data is changed and not written to disk, changed data is overwritten by the old data stored on disk when the hourly data update occurs.
  • Page 222 4-62 Section 060-INDP-410 Command and Message Guide The following example shows how to modify the value of the block count threshold for the AMACRD file. >VALPARM BLOCKS num (cr) The system displays the following message: BLOCKS TO CLOSE FILE = num CAUTION A change in validation parameters can affect polling validation.
  • Page 223: Software Version Command

    Section 060-INDP-410 Command and Message Guide 4-63 Software version command The software version command, VS, is included for diagnostic and support purposes. This command displays the version of the firmware and software the BMC is running. VS displays software program version ID and firmware version ID. Example of command usage To display the software and firmware program version for the active processor, issue the following command:...
  • Page 224: Statistics Commands

    4-64 Section 060-INDP-410 Command and Message Guide Statistics commands The statistics commands provide a means of obtaining and printing summaries of critical system activities on a daily basis. Reports can be obtained for a given day or the previous day. The statistics commands are as follows: •...
  • Page 225 Section 060-INDP-410 Command and Message Guide 4-65 period -specifies the report period. Values: TDAY (activity for current day) or YDAY (activity for one day previous). The system displays the requested report as follows, all fields are eight digits with leading 0s suppressed. period'S REPORT AMA STATISTICS (From TEC/DSI Interface)
  • Page 226 4-66 Section 060-INDP-410 Command and Message Guide The TOTAL AMA POLLED (SEC) field contains the total number of Secondary AMA blocks polled since midnight. If no data is found in the previous day's statistics file, the following message is generated: NO DATA ACCUMULATED REPORT COM REPORT COM is used to request polling summary reports from the BMC...
  • Page 227 Section 060-INDP-410 Command and Message Guide 4-67 period -specifies the report period. Values: TDAY (activity for current day) or YDAY (activity for one day previous). The system responds with the following report: period'S REPORT DISK STATISTICS DISK...AB VENDOR ID .
  • Page 228: System Clock Command

    4-68 Section 060-INDP-410 Command and Message Guide The DISK CAPACITY (LB) field indicates the size of the disk drive in logical blocks. The USER CAPACITY (LB) field indicates the amount of disk drive space, in logical blocks, that is available to the user. Note 16: If this report is requested while the disk system is in AO or BO, the report column for off-line disk contains the characters N/A for VENDOR ID, REVISION LEVEL, DISK CAPACITY,...
  • Page 229: Tec/Dsi Commands

    Section 060-INDP-410 Command and Message Guide 4-69 where: x - processor ID (Range: A or B). TEC/DSI commands The TEC/DSI commands relate to the control over and examination of the characteristics of the circuits that interface the BMC with the Switching System.
  • Page 230: Tecmaint Iowrite

    4-70 Section 060-INDP-410 Command and Message Guide where: side- TEC/DSI port ID: 1 (TEC/DSI PCA in slot 13) or 2 (TEC/DSI PCA in slot 12) port- decimal number that specifies a port. Range: 0-255. The system displays the data at the specified port address. TECMAINT IOWRITE TECMAINT IOWRITE writes data to a specified TEC/DSI port address.
  • Page 231: Tecmaint Select

    Section 060-INDP-410 Command and Message Guide 4-71 side- TEC/DSI port ID: 1 (TEC/DSI PCA in slot 13) or 2 (TEC/DSI PCA in slot 12) address- four-digit hex value that specifies a memory address range. Range: 0000-FFFF datalist- data bytes to be written to the specified TEC/DSI memory address.
  • Page 232: Tecmaint Show

    4-72 Section 060-INDP-410 Command and Message Guide TECMAINT SHOW The TECMAINT SHOW command displays requested data on specified TEC/DSI PCA. The following table lists the subcommands for the TECMAINT SHOW command. Table 4-18 TECMAINT SHOW subcommands Subcommand Description side ERROR Displays the Cyclic Redundancy Check (CRC), parity and communication TEC/DSI errors from the specified TEC/DSI.
  • Page 233 Note: All of the other values are combinations of the codes listed. In the event this printout indicates a faulty condition, record the values for use in conjunction with Nortel field service personnel in the troubleshooting efforts. BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 234: Tecram

    4-74 Section 060-INDP-410 Command and Message Guide Use the following command to display the firmware program version on a specified TEC/DSI PCA: >TECMAINT SHOW side VS (cr) The system responds with the following message: aaa-bbb-e mm/dd/yy where: - program dash number - firmware identifier - one character decimal patch level mm/dd/yy - assembly date (month/day/year).
  • Page 235: Test Commands

    Section 060-INDP-410 Command and Message Guide 4-75 Test commands The test commands provide a low level of diagnostics. These commands are used to verify the operating condition of major components of the BMC. The test commands are as follows: • DPRTST •...
  • Page 236 4-76 Section 060-INDP-410 Command and Message Guide B0 TEC TEST PASSED B2 TEC TEST PASSED DMA TEST PASSED RAM TEST PASSED ROM TEST PASSED PRG TEST PASSED Note 18: These tests run independently. The test completion order shown above is only an example. The order in which the tests complete can vary.
  • Page 237 Section 060-INDP-410 Command and Message Guide 4-77 ON -specifies that block headers are to be displayed as they are being written to disk. OFF -specifies that the block headers are not to be displayed as they are being written to disk. The system displays the following message: (ON option) LOGGING OF AMA HEADERS ENABLED...
  • Page 238 4-78 Section 060-INDP-410 Command and Message Guide Example of command usage To exit the BMC human-machine interface, enter the following at the maintenance terminal: >BYE (cr) The system responds with the following message: yy-mm-dd hh:mm:ss PROC-x USER yy LOGGED OUT where: yy - year mm - month...
  • Page 239 Section 060-INDP-410 Command and Message Guide 4-79 DELETE DELETE is used to remove a specified file or range of files from the BMC system directory. Files are stored on the BMC in different versions. The disk directory can hold 255 versions of a given file type. The BMC stores files in sequential order (starts with zero and creates new file until 255 versions of the file have been created).
  • Page 240 4-80 Section 060-INDP-410 Command and Message Guide where: aaaaaa - filename. vvv - version number (0-255). Note 22: The above deletes one disk file version. To delete a range of versions, enter the following at the maintenance terminal: >DELETE aaaaaa xxx:yyy (cr) where: xxx - starting file version (0-255) yyy - ending file version (0-255).
  • Page 241 Section 060-INDP-410 Command and Message Guide 4-81 Examples of command usage To examine the system password, enter the following at the maintenance terminal: >DMSP (cr) To change the system password, enter the following at the maintenance terminal: >DMSP xxxx (cr) where: xxxx - four-character ASCII value of the DMS-10 main password.
  • Page 242 4-82 Section 060-INDP-410 Command and Message Guide If "D" is specified as the gg variable, the command is used to delete the log terminal assignment. Note: Use the SITDAT WRITE and LINIT commands to save any changes and update the CP with the new values. CAUTION The passwords assigned using the DMSP command must match the password stored in the DMS-10 when log...
  • Page 243 Section 060-INDP-410 Command and Message Guide 4-83 3. To restart data entry for the file being edited, enter the following at the maintenance terminal: R (cr) 4. To exit a file edit task with no file created, enter the following at the maintenance terminal: Q (cr) 5.
  • Page 244 4-84 Section 060-INDP-410 Command and Message Guide To delete the last file name from the list contained in the boot file, enter the following at the maintenance terminal: >DOS LD (cr) To list the contents of a boot file, enter the following at the maintenance terminal: >DOS LL (cr) To read 16 bytes of firmware or software memory, starting at a specified...
  • Page 245 Section 060-INDP-410 Command and Message Guide 4-85 To display the firmware version, enter the following at the maintenance terminal: >DOS VS (cr) STIM STIM is a firmware command used to set the BMC system clock. Note 26: When software is up and running, STIM command is not permitted.
  • Page 246 4-86 Section 060-INDP-410 Command and Message Guide XDIR XDIR is used to list all files currently in the BMC disk system directory. The output also contains the number of used tracks on disk and the total number of tracks available for use. Examples of command usage To list all files in the directory, enter the following at the maintenance terminal:...
  • Page 247 Section 060-INDP-410 Command and Message Guide 4-87 yy-mm-dd hh:mm:ss day PROC x pppsxxxnni where: yy - calender year (00-99) mm - month (01-12) dd - day (1-31) hh:mm:ss - time of day (0-23:0-59:0-59) day - day (MON, TUE, WED, THU, FRI, SAT, or SUN) x - active processor (A or B) ppp - message type blank - informational...
  • Page 248 4-88 Section 060-INDP-410 Command and Message Guide BMC System Information Message Descriptions The following table describes the messages issued by the BMC as part of normal functioning. The messages listed in this section do not require any maintenance activities. Table 4-20 BMC BISYNC Information Messages Message Text Description...
  • Page 249 Section 060-INDP-410 Command and Message Guide 4-89 Table 4-20 BMC BISYNC Information Messages Message Text Description CP DGN - Testing not performed Output in response to the CP TEST ACT and CP TEST due to a polling STDBY commands when a polling session is in progress. DISK: REASSIGN STARTED Indicates that the scheduled bad disk sector relocation process has started.
  • Page 250 4-90 Section 060-INDP-410 Command and Message Guide Table 4-20 BMC BISYNC Information Messages Message Text Description NO SECONDARY BLOCKS EXIST Output when the BMC Status File Report does not contain any secondary data blocks. NO SESSION DATA ON DISK Output when the Data Transfer Session report is requested, and no session is in progress and no previous session data is available on disk.
  • Page 251 Section 060-INDP-410 Command and Message Guide 4-91 Table 4-20 BMC BISYNC Information Messages Message Text Description xxxxxx DOWNLOAD STARTED where: xxxxxx - filename of the downloading file. Output on the starting of a download procedure. YDYSTS FILE DISK JOB Issued when a disk update of the YDYSTS file has been COMPLETE completed.
  • Page 252 4-92 Section 060-INDP-410 Command and Message Guide BMC System Error Message Descriptions BMC system error message descriptions are provided, in alphabetical order, on the following pages. Each message listed indicates whether the message is the result of a system error and, in such cases, is referenced to the Maintenance Procedures Guide subsection for corrective procedures.
  • Page 253 Section 060-INDP-410 Command and Message Guide 4-93 Table 4-21 ? message Cause: bell (chime) sounds and the message is output automatically when the system does not understand a Display: Maintenance terminal user command that has been entered. Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A System Default: Type:N/ALevel:N/A...
  • Page 254 4-94 Section 060-INDP-410 Command and Message Guide Table 4-22 00 PIO TEST FAILED message Other Alarm Indications Default: Status Panel:MajorAudible:Major Customer-Selected Status Panel:Audible: System Recovery Action None Craftsperson Activity: If the standby processor is off, this message is normal. If the standby processor is on, refer to the Boot Recovery Procedure in the Maintenance Procedures Guide section.
  • Page 255 Section 060-INDP-410 Command and Message Guide 4-95 Table 4-23 ACTIVE PROC ALARM - NO SWITCH message System Recovery Action None; system processors are unable to reconfigure. Craftsperson Activity: Verify the position of the Status Panel rockers. If the rockers are set to “O” and the ONL lamp is lit, determine whether troubleshooting is in progress.
  • Page 256 4-96 Section 060-INDP-410 Command and Message Guide Table 4-25 BAD CKSM message BAD CKSM Cause: A program load from disk failed because the calculated checksum did not compare to the file Display: Maintenance terminal checksum stored on the disk. This is an indication that one of the following occurred: a.
  • Page 257 Section 060-INDP-410 Command and Message Guide 4-97 Table 4-26 BAD INTERFACE BAD INTERFACE Cause: output when an incorrect value was input for the CP INTERFACE command. Display: Maintenance terminal Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A System Default: Type:N/ALevel:N/A Customer-Selected Alarm Level...
  • Page 258 4-98 Section 060-INDP-410 Command and Message Guide Table 4-27 BAD LINE CONTROL SELECTION message Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: System Recovery Action None Craftsperson Activity: Enter the correct line control type (listed in message). Refer to the CP CONTROL subsection in this document for more information.
  • Page 259 Section 060-INDP-410 Command and Message Guide 4-99 Table 4-29 BAD S/W CKSM message BAD S/W CKSM Cause: output when the checksum test on software program file(s) failed on download. Display: Maintenance terminal Alarm Level: Reason Code = N/A Processor switch Corresponds to ERRMAP entry: PROG CHKSM ALM System Default: Type:MajorLevel:3...
  • Page 260 4-100 Section 060-INDP-410 Command and Message Guide Table 4-30 BAD xxxIDX FILE message Customer-Selected Alarm Level Type:Level: Other Alarm Indications Default: Status Panel:MinorAudible:Minor Customer-Selected Status Panel:Audible: System Recovery Action None Refer to the Index Corruption Recovery Procedure in Craftsperson Activity: the Maintenance Procedures Guide section.
  • Page 261 Section 060-INDP-410 Command and Message Guide 4-101 Table 4-32 BLOCK PARITY ERROR DETECTED message BLOCK PARITY ERROR Cause: output when a block parity error is detected by DETECTED the TEC/DSI PCA. This alarm is generated when the number of invalid blocks received exceeds the Display: Log message threshold limit for invalid blocks set using the VALPARM BLOCKS command.
  • Page 262 4-102 Section 060-INDP-410 Command and Message Guide Table 4-33 BLOCK REJECTED: xxxx BYTES message BLOCK REJECTED: xxxx BYTES Where: xxxx = number of bytes in the rejected block. Display: Log message Cause: output when a block greater than 2050 bytes is received by the TEC/DSI PCA from the Switching System.
  • Page 263 Section 060-INDP-410 Command and Message Guide 4-103 Table 4-34 BOOT FILE EMPTY message BOOT FILE EMPTY Cause: output because the file, BOOTFL, is found to contain an empty list (no software in the file) while Display: Log message attempting a re-boot operation. Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A...
  • Page 264 4-104 Section 060-INDP-410 Command and Message Guide Table 4-35 BOTH DISKS FULL message Customer-Selected Alarm Level Type:Level: Other Alarm Indications Default: Status Panel:CriticalAudible:Critical Customer-Selected Status Panel:Audible: System Recovery Action System has already set disk status nonredundant. Refer to the Disk Drive Diagnostic Procedure in the Craftsperson Activity: Maintenance Procedures Guide section to alleviate this condition.
  • Page 265 Section 060-INDP-410 Command and Message Guide 4-105 Table 4-36 BX.25 INTER-TASK COMM ERROR message System Recovery Action Polling ceases. Craftsperson Activity: If this message is persistent, refer to the 56K Interface PCA Replacement Procedure in the Maintenance Procedures Guide section. Table 4-37 Bx TEC BUSY message B0 TEC BUSY...
  • Page 266 4-106 Section 060-INDP-410 Command and Message Guide Table 4-38 Bx TEC COLD START message 1 0 3 (log message) Where: x = TEC/DSI Port ID B0 TEC COLD START = 0 = TEC/DSI PCA in slot 13. (log message) = 2 = TEC/DSI PCA in slot 12. B2 TEC COLD START Cause: output at initial power-up, or after four warm Display: Log message...
  • Page 267 Section 060-INDP-410 Command and Message Guide 4-107 Table 4-39 Bx TEC COMM FAIL message 1 0 9 (log message) Where: x = TEC/DSI Port ID B0 TEC COMM FAIL = 0 = TEC/DSI PCA in slot 13. (log message) = 2 = TEC/DSI PCA in slot 12. B2 TEC COMM FAIL Cause: output when the processor cannot Display: Log message...
  • Page 268 4-108 Section 060-INDP-410 Command and Message Guide Table 4-40 Bx TEC DMA FAIL message 1 1 5 (log message) Where: x = TEC/DSI Port ID B0 TEC DMA FAIL = 0 = TEC/DSI PCA in slot 13. (log message) = 2 = TEC/DSI PCA in slot 12. B2 TEC DMA FAIL Cause: output when a DMA transfer of a data block has Display: Log message...
  • Page 269 Section 060-INDP-410 Command and Message Guide 4-109 Table 4-41 Bx TEC NOT READY message 1 2 1 (log message) Where: x = TEC/DSI Port ID B0 TEC NOT READY = 0 = TEC/DSI PCA in slot 13. (log message) = 2 = TEC/DSI PCA in slot 12. B2 TEC NOT READY Cause: output when there is a loss of unit select from Display: Log message...
  • Page 270 4-110 Section 060-INDP-410 Command and Message Guide Table 4-42 Bx TEC TIME OUT message 1 2 7 (log message) Where: x = TEC/DSI Port ID B0 TEC TIME OUT = 0 = TEC/DSI PCA in slot 13. (log message) = 2 = TEC/DSI PCA in slot 12. B2 TEC TIME OUT Cause: output when a request for the transfer of a data Display: Log message...
  • Page 271 Section 060-INDP-410 Command and Message Guide 4-111 Table 4-43 Bx TEC WARM START message 1 3 3 (log message) Where: x = TEC/DSI Port ID B0 TEC WARM START = 0 = TEC/DSI PCA in slot 13. (log message) = 2 = TEC/DSI PCA in slot 12. B2 TEC WARM START Cause: output at restart with RAM intact (program not Display: Log message...
  • Page 272 4-112 Section 060-INDP-410 Command and Message Guide Table 4-44 CALL RECORD BLOCK FROM TEC INCORRECT message 1 3 9 (log message) Cause: output for one of the following reasons: CALL RECORD BLOCK FROM TEC INCORRECT a. data block received from the Switching System is not a valid LSSGR billing data block.
  • Page 273 Section 060-INDP-410 Command and Message Guide 4-113 Table 4-45 COMMAND ALREADY IN PROGRESS message 1 4 5 COMMAND ALREADY IN Cause: output in response to commands (those which PROGRESS generate large amounts of output) if the user tries to execute other commands before completion of the Display: Maintenance terminal active command.
  • Page 274 4-114 Section 060-INDP-410 Command and Message Guide Table 4-46 COMM DOWN TO STANDBY PROCESSOR message 1 5 1 COMM DOWN TO STANDBY Cause: processor communication with the standby PROCESSOR processor is not possible for one of the reasons listed below. This message is cleared automatically when the Display: Log message condition causing it to occur is corrected.
  • Page 275 Section 060-INDP-410 Command and Message Guide 4-115 Table 4-47 CP ACTIVATE FAIL message 1 5 7 CP ACTIVATE FAIL Cause: 56K Interface responded incorrectly to an attempt to start the downloaded 56K Interface software. Display: Log message 1 5 8 Alarm Level: Reason Code = N/A Major...
  • Page 276 4-116 Section 060-INDP-410 Command and Message Guide Table 4-48 CP AUDIT FAIL message 1 6 3 CP AUDIT FAIL Cause: 56K Interface responded improperly to an audit command. Display: Log message 1 6 4 Alarm Level: Reason Code = N/A Major Corresponds to ERRMAP entry: CP FAULT CP NOT AVAIL.
  • Page 277 Section 060-INDP-410 Command and Message Guide 4-117 Table 4-49 CP BOOT LIST EMPTY message 1 6 9 CP BOOT LIST EMPTY Cause: output when no load file names are found in the 56K Interface boot list file, BOOTCP, during the booting Display: Log message procedure.
  • Page 278 4-118 Section 060-INDP-410 Command and Message Guide Table 4-50 CP BX CODE xx WAS yy message 1 7 5 CP BX CODE xx WAS yy Where: xx = expected code. yy = received code. Display: Log message Cause: output when the polling task on the MP is unable to communicate with the CP.
  • Page 279 Section 060-INDP-410 Command and Message Guide 4-119 Table 4-51 CP COMMAND NOT ACCEPTED message 1 8 1 (log message) Cause: output when the CP will not accept site data CP COMMAND NOT ACCEPTED written to or read from the disk such as on the hour. It is output as a response to any CP command that is not Display: Log message accepted.
  • Page 280 4-120 Section 060-INDP-410 Command and Message Guide Table 4-52 CP CM CODE xx WAS yy message 1 8 7 CP CM CODE xx WAS yy Where: xx = expected code. yy = received code. Display: Log message Cause: output when the CP command code is not as expected for the CP command task.
  • Page 281 Section 060-INDP-410 Command and Message Guide 4-121 Table 4-53 CP DATA ERR message 1 9 3 CP DATA ERR Cause: output when an error is detected while transferring data between the CP and MP. Display: Log message 1 9 4 Alarm Level: Reason Code = N/A Major...
  • Page 282 4-122 Section 060-INDP-410 Command and Message Guide Table 4-54 CP DMA Test: DMA Busy message 1 9 9 CP DMA Test: DMA Busy Cause: response to the CP TEST ACT or CP TEST STDBY command; this message should never appear. Display: Maintenance terminal If the CP TEST ACT or CP TEST STDBY command is entered during a polling session, the message, CP...
  • Page 283 Section 060-INDP-410 Command and Message Guide 4-123 Table 4-55 CP DMA Test Failed message 2 0 5 CP DMA Test Failed Cause: 56K Interface DMA test failed. Display: Maintenance terminal 2 0 6 Alarm Level: Reason Code = N/A Processor switch Corresponds to ERRMAP entry: CP FAULT CP NOT AVAIL.
  • Page 284 4-124 Section 060-INDP-410 Command and Message Guide Table 4-56 CP I/O FAILURE message 2 1 3 Customer-Selected Alarm Level Type:Level: 2 1 4 Other Alarm Indications Default: Status Panel: MajorAudible: Major Customer-Selected Status Panel:Audible: 2 1 5 System Recovery Action System attempts a 56K Interface restart.
  • Page 285 Section 060-INDP-410 Command and Message Guide 4-125 Table 4-57 CP LOAD FAIL message 2 2 1 System Recovery Action System attempts a 56K Interface restart. If the 56K Interface processor cannot successfully complete a restart, the alarm is upgraded to CP NOT AVAILABLE. 2 2 2 Craftsperson Activity: Refer to the 56K Interface PCA Diagnostic Procedure in...
  • Page 286 4-126 Section 060-INDP-410 Command and Message Guide Table 4-59 CP_MMI_TSK - Memory RD/WR bad address received from the MP message 2 2 9 CP_MMI_TSK - Memory RD/WR bad Cause: response to CP MEMWRITE and CP EXAMINE address received from the MP commands;...
  • Page 287 Section 060-INDP-410 Command and Message Guide 4-127 Table 4-60 CP Modem Loopback Test Failed on SCC Channel x message 2 3 7 Customer-Selected Alarm Level Type:Level: 2 3 8 Other Alarm Indications Default: Status Panel: Audible: Customer-Selected Status Panel:Audible: 2 3 9 System Recovery Action None 2 4 0...
  • Page 288 4-128 Section 060-INDP-410 Command and Message Guide Table 4-61 CP MS CODE xx WAS yy message 2 4 5 System Recovery Action None 2 4 6 Craftsperson Activity: Try to repeat this task with a key command. If the problem persists, reload the CP using the LINIT command.
  • Page 289 Section 060-INDP-410 Command and Message Guide 4-129 Table 4-63 CP RAM Test Failed message 2 5 3 CP RAM Test Failed Cause: the 56K Interface RAM test failed. A RAM chip may be corrupted or the parity circuitry has failed. Display: Maintenance terminal 2 5 4 Alarm Level:...
  • Page 290 4-130 Section 060-INDP-410 Command and Message Guide Table 4-64 CP RESTART FAIL message 2 5 9 CP RESTART FAIL Cause: 56K Interface PCA responded improperly to a reset condition. Display: Log message 2 6 0 Alarm Level: Reason Code = N/A Major Corresponds to ERRMAP entry: CP FAULT CP NOT AVAIL.
  • Page 291 Section 060-INDP-410 Command and Message Guide 4-131 Table 4-65 CP ROM Checksum Test Failed message 2 6 5 CP ROM Checksum Test Failed Cause: the 56K Interface EPROM checksum test failed. The EPROM is corrupted or there is a bad checksum Display: Maintenance terminal byte.
  • Page 292 4-132 Section 060-INDP-410 Command and Message Guide Table 4-66 CP ROM CKSM ERR message 2 7 1 CP ROM CKSUM ERR Cause: the 56K Interface EPROM checksum test failed. The EPROM is corrupted or there is a bad checksum Display: Maintenance terminal byte.
  • Page 293 Section 060-INDP-410 Command and Message Guide 4-133 Table 4-67 CP SCC Channel x Busy message 2 7 7 CP SCC Channel x Busy Where: x = channel identifier (A or B) Display: Maintenance terminal Cause: response to the CP TEST ACT or CP TEST STDBY command;...
  • Page 294 4-134 Section 060-INDP-410 Command and Message Guide Table 4-68 CP SCC Channel x test: DMA Busy message 2 8 3 CP SCC Channel x test: DMA Busy Where: x = channel identifier (A or B) Display: Maintenance terminal Cause: response to the CP TEST ACT or CP TEST STDBY command;...
  • Page 295 Section 060-INDP-410 Command and Message Guide 4-135 Table 4-69 CP SCC Loopback Test Failed on Channel x message 2 8 9 CP SCC Loopback Test Failed on Where: x = channel identifier (A or B) Channel x Cause: 56K Interface SCC loopback test failed for the Display: Maintenance terminal designated channel.
  • Page 296 4-136 Section 060-INDP-410 Command and Message Guide Table 4-70 CP ST CODE xx WAS yy message 2 9 5 CP ST CODE xx WAS yy Where: xx = expected code. yy = received code. Display: Log message Cause: output when the CP command code is not as expected for the CP statistics task.
  • Page 297 Section 060-INDP-410 Command and Message Guide 4-137 Table 4-71 CP TASK ERR message 3 0 1 CP TASK ERR Cause: an illogical condition was detected by the 56K Interface PCA system software. Display: Log message 3 0 2 Alarm Level: Reason Code = N/A Major Corresponds to ERRMAP entry: CP FAULT...
  • Page 298 4-138 Section 060-INDP-410 Command and Message Guide Table 4-72 CP TIMEOUT message 3 0 7 CP TIMEOUT Cause: the 56K Interface failed to respond to a continuous audit or synchronization command. Display: Maintenance terminal 3 0 8 Alarm Level: Reason Code = N/A Major Corresponds to ERRMAP entry: CP FAULT CP NOT AVAIL.
  • Page 299 Section 060-INDP-410 Command and Message Guide 4-139 Table 4-73 CP xxx_TSK_ERR: y message 3 1 3 CP xxx_TSK_ERR: y Where: xxx =DGN - error during a diagnostic task execution. Display: Log message MMI - error during an MMI task execution. MSG - error during a message task execution.
  • Page 300 4-140 Section 060-INDP-410 Command and Message Guide Table 4-74 CTC MP-ST-ALM message 3 1 9 (log message) Cause: output to report a processor status alarm. CTC MP-ST-ALM (Counter Timer Circuit Microprocessor-Status-Alarm) Display: Log message 3 2 0 Alarm Level: Reason Code = 17 Processor switch Corresponds to ERRMAP entry: PROC STAT ALM System Default:...
  • Page 301 Section 060-INDP-410 Command and Message Guide 4-141 Table 7-75 DATA BUFFER EXCEEDED ALARM message DATA BUFFER EXCEEDED Cause: a block has been received that overwrites the ALARM oldest data block not yet processed (buffer full). The BMC was not able to write a block to disk because the Display: Log message buffers were full.
  • Page 302 4-142 Section 060-INDP-410 Command and Message Guide Table 7-76 DATA IGNORED message DATA IGNORED Cause: indicates a program data record was incorrectly entered while using a patch file command. Display: Maintenance terminal Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A System Default: Type:N/ALevel:N/A Customer-Selected Alarm Level...
  • Page 303 Section 060-INDP-410 Command and Message Guide 4-143 Table 7-77 DATA NOT AVAILABLE message Other Alarm Indications Default: Status Panel: Audible: Customer-Selected Status Panel:Audible: System Recovery Action EOT message is sent to HOC. Craftsperson Activity: Input the IDXMAINT SUMMARY AMA command. Verify that the number of blocks to poll is greater than the value assigned using VALPARM BLOCKS command.
  • Page 304 4-144 Section 060-INDP-410 Command and Message Guide Table 7-79 DISK ALARM x message DISK ALARM x Where: x = disk drive (A or B) Display: Log message Cause: message is output to report that an alarm threshold value has been exceeded. Output for the following reasons: a.
  • Page 305 Section 060-INDP-410 Command and Message Guide 4-145 Table 7-80 DISK BUFFER NOT AVAILABLE message (log message) Cause: no disk buffer is available when attempting to DISK BUFFER NOT AVAILABLE write statistical data to files on disk. Display: Log message Alarm Level: Reason Code = N/A No processor switch Corresponds to ERRMAP entry: DSK CARD HW ERR...
  • Page 306 4-146 Section 060-INDP-410 Command and Message Guide Table 7-81 DISK COMMAND xx ATTEMPTED WHILE DISK BUSY message (log message) Where: DISK COMMAND xx ATTEMPTED xx - two letter code for the disk command that was WHILE DISK BUSY being transferred to or carried out by the OMTI disk DISK JOB: yy, controller.
  • Page 307 Section 060-INDP-410 Command and Message Guide 4-147 Table 7-81 DISK COMMAND xx ATTEMPTED WHILE DISK BUSY message (continued) Parameters = aa bb cc(1) cc(2) cc(3) dd(1) dd(2) aa =quantity of sectors involved, (in Hex). bb =drive unit number, (in Hex). cc(1) cc(2) cc(3) = logical sector number, (in Hex).
  • Page 308 4-148 Section 060-INDP-410 Command and Message Guide Table 7-82 DISK DIRECTORY FULL message (log message) Cause: output when the disk directory meets the DISK DIRECTORY FULL following conditions: Display: Log message a. maximum number of files that can exist is exceeded. When an attempt is made to create an AMA index file fails because the disk directory is full, an attempt is made to delete the oldest secondary file.
  • Page 309 Section 060-INDP-410 Command and Message Guide 4-149 Table 7-83 DISK DPR FAULT message (log message) Cause: output when an error is detected during the self- DISK DPR FAULT check (test) on the DPR. Display: Log message Alarm Level: Reason Code = 30 Processor switch Corresponds to ERRMAP entry: DSK CARD HW ERR System Default:...
  • Page 310 4-150 Section 060-INDP-410 Command and Message Guide Table 7-84 DISK MODE ALARM message DISK MODE ALARM Cause: disk system found to be nonredundant at hour boundary. Display: Log message a. fault caused disk system to become nonredundant. b. one disk is 100% full; system becomes nonredundant to use second disk for additional primary data.
  • Page 311 Section 060-INDP-410 Command and Message Guide 4-151 Table 7-85 DISK MODE: NONE message DISK MODE: NONE Cause: response to a manual request for current disk mode status and neither disk is formatted. This Display: Log message message is also output upon system restart, if neither is formatted.
  • Page 312 4-152 Section 060-INDP-410 Command and Message Guide Table 7-86 DISK NOT READY SIDE x message (log message) Where: x = disk drive (A or B) DISK NOT READY SIDE x Cause: output when the system SCSI Interface is going through initialization and the indicated drive unit does Display: Log message not return READY status after 30 seconds.
  • Page 313 Section 060-INDP-410 Command and Message Guide 4-153 Table 7-87 DISK QUEUE ERROR message (log message) Cause: output if no free command nodes are available. DISK QUEUE ERROR Display: Log message Alarm Level: Reason Code = 29 Corresponds to ERRMAP entry: DSK CARD HW ERR System Default: Type:MajorLevel:2 Customer-Selected Alarm Level...
  • Page 314 4-154 Section 060-INDP-410 Command and Message Guide Table 7-88 DISK TEST FAILED message DISK TEST FAILED Cause: output when the disk test requested has failed. Display: Maintenance terminal Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: DSK ERROR ALM System Default: Type:CriticalLevel:0 Customer-Selected Alarm Level...
  • Page 315 Section 060-INDP-410 Command and Message Guide 4-155 Table 7-89 DISK USE > xx% message DISK USE > xx% Where: xx = disk use percent; Values: 70, 90 or 99. Display: Log message Cause: output anytime disk usage reaches 70, 90, or 99% of capacity.
  • Page 316 4-156 Section 060-INDP-410 Command and Message Guide Table 7-89 DISK USE > xx% message Customer-Selected Alarm Level Type:Level: Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: System Recovery Action System performs disk recovery procedure; sets DISK MODE ONLY when one disk reaches 100% full. Craftsperson Activity: Refer to the Disk Drive Diagnostic Procedure in the Maintenance Procedures Guide section.
  • Page 317 Section 060-INDP-410 Command and Message Guide 4-157 Table 7-90 DISK USE > xx% PRIMARY DATA message (continued) Case 2:disk mode non-redundant; one disk already at maximum AMA capacity and the other disk is operating in the ONLY mode. On the ONLY disk, which is currently the ONLY disk available to accept incoming data: d.
  • Page 318 4-158 Section 060-INDP-410 Command and Message Guide Table 7-91 DISK VS NOT FOUND message 1 0 3 (log message) Cause: output on a processor switch, power-up, or DISK VS NOT FOUND when booting the Active Processor, if the disk version sent from the disk is not in the table of disk versions in Display: Log message the software (defaults are set to NO BAD TRACK...
  • Page 319 After processor switch activity ceases, proceed to step Determine whether the problem message repeats. If the message does not repeat, the procedure is complete. Report this incident to Nortel as soon as possible. If the error message repeats, call your next level of support.
  • Page 320 4-160 Section 060-INDP-410 Command and Message Guide Table 7-91 DISK VS NOT FOUND message (continued) If the version number is incorrect, contact your next level of support to load the correct software to the BMC system. If the error message does not repeat after installation of the new software, the procedure is complete.
  • Page 321 Section 060-INDP-410 Command and Message Guide 4-161 Table 7-92 DISK x HAS INSUFFICIENT CAPACITY message 1 0 9 DISK x HAS INSUFFICIENT where: x = disk drive (A or B). CAPACITY Cause: occurs when: Display: Maintenance terminal a. user attempts to change the disk mode from NONE to ONLY and the selected disk drive unit supports less memory space than required for the software load (1 gigabyte).
  • Page 322 4-162 Section 060-INDP-410 Command and Message Guide Table 7-93 DISK: BACKUP FAILED message 1 1 5 DISK: BACKUP FAILED Cause: output upon termination due to a failure of the disk backup operation. Backup operation attempted as Display: Log message a result of an ONLY to PRIME disk mode change request.
  • Page 323 Section 060-INDP-410 Command and Message Guide 4-163 Table 7-94 DISK: BOTH DISKS CONTAINED PREFERRED STATUS message 1 2 1 (log message) Cause: output when: DISK: BOTH DISKS CONTAINED PREFERRED a. SCSI Interface is going through initialization; both STATUS disks are found to contain status data indicating that each disk should be the only on-line and active disk.
  • Page 324 4-164 Section 060-INDP-410 Command and Message Guide Table 7-95 DISK: BUS CONTROLLER FAILED SELF TEST message 1 2 7 DISK: BUS CONTROLLER FAILED Where: x = disk drive (A or B) SELF TEST, DISK: x Cause: output when the SCSI Interface or the SCSI bus Display: Log message controller fails its self test.
  • Page 325 Section 060-INDP-410 Command and Message Guide 4-165 Table 7-96 DISK: BUS CONTROLLER INTERRUPT WHILE IDLE message 1 3 3 (log message) Where: DISK: BUS CONTROLLER xx = contents of the bus controller auxiliary status INTERRUPT WHILE IDLE register (in Hex). AUXILIARY STATUS: xx, yy = contents of the bus interrupt status register (in INTERRUPT STATUS yy...
  • Page 326 4-166 Section 060-INDP-410 Command and Message Guide Table 7-97 DISK: BUS DATA TRANSFER BYPASSED AUXILIARY message 1 3 9 (log message) Where: DISK: BUS DATA TRANSFER xx = contents of the bus controller auxiliary status BYPASSED AUXILIARY register (in Hex). STATUS: xx, INTERRUPT STATUS: yy = contents of the bus interrupt status register (in yy STAGE: aa DRIVE: bb DISK...
  • Page 327 Section 060-INDP-410 Command and Message Guide 4-167 Table 7-97 DISK: BUS DATA TRANSFER BYPASSED AUXILIARY message (continued) Relocate track from prime; — used by backup: L1 = read prime L2 = seek prime L3 = seek standby L4 = write prime L5 = write standby Assign disk parameters.: PA = To A PB = To B RC = recalibrate...
  • Page 328 4-168 Section 060-INDP-410 Command and Message Guide Table 7-97 DISK: BUS DATA TRANSFER BYPASSED AUXILIARY message 1 4 2 Other Alarm Indications Default: Status Panel:MinorAudible:Minor Customer-Selected Status Panel:Audible: 1 4 3 System Recovery Action Disk mode goes to ONLY mode. 1 4 4 Refer to the Disk Drive Diagnostic Procedure in the Craftsperson Activity:...
  • Page 329 Section 060-INDP-410 Command and Message Guide 4-169 Table 7-98 DISK: BUS ERROR, m message (continued) w = Job name Read Redundant Write Redundant Read Single Write Single Backup Read Disk Capacity Read Number Reassign Bad Sector of Defects Format Inquiry Check Disk x = Command Name Format Unit...
  • Page 330 4-170 Section 060-INDP-410 Command and Message Guide Table 7-99 DISK: COMMAND ERROR message 1 5 1 DISK: COMMAND ERROR, Where: COMMAND: xJOB: w w = Job name SECTOR: ab cd ef gh Read Redundant Write Redundant DISK: y, zSENSE: r, s Read Single Write Single Backup...
  • Page 331 Section 060-INDP-410 Command and Message Guide 4-171 Table 7-99 DISK: COMMAND ERROR message (continued) Medium Error, ID Field CRC Error Uncorrectable Error No ID Field Address Mark No Data Field Address Mark Block Not Found Seek Error Format Failed No Defect Spare Location Available Hardware Error, No Seek Complete Write Fault...
  • Page 332 4-172 Section 060-INDP-410 Command and Message Guide Table 7-99 DISK: COMMAND ERROR message 1 5 2 Alarm Level: Reason Code = 27 Possible disk mode change Corresponds to ERRMAP entry: DISK ER MESSAGE System Default: Type:MinorLevel:0 1 5 3 Customer-Selected Alarm Level Type:Level: 1 5 4 Other Alarm Indications...
  • Page 333 Section 060-INDP-410 Command and Message Guide 4-173 Table 7-100 DISK: DMA INTERRUPT message 1 6 0 Other Alarm Indications Default: Status Panel:MinorAudible:Minor Customer-Selected Status Panel:Audible: 1 6 1 System Recovery Action Attempt to change disk mode to ONLY mode. 1 6 2 Craftsperson Activity: If the attempt is successful, system continues normally.
  • Page 334 4-174 Section 060-INDP-410 Command and Message Guide Table 7-102 DISK: MULTIPLE REASSIGN CONDITION message 1 6 9 DISK: MULTIPLE REASSIGN Cause: this message follows a DISK: COMMAND CONDITION ERROR message. An additional bad sector has been located on the disk. Relocation cannot be scheduled; Display: Maintenance terminal data in that sector is lost.
  • Page 335 Section 060-INDP-410 Command and Message Guide 4-175 Table 7-103 DISK: PROCEDURE IN PROGRESS message 1 7 5 DISK: PROCEDURE IN PROGRESS Cause: output if any of the following are attempted while any of the following are already in progress. Display: Maintenance terminal a.
  • Page 336 4-176 Section 060-INDP-410 Command and Message Guide Table 7-104 DISK: REASSIGN COMPLETED message 1 8 3 Customer-Selected Alarm Level Type:Level: 1 8 4 Other Alarm Indications Default: Status Panel:MajorAudible:Major Customer-Selected Status Panel:Audible: 1 8 5 System Recovery Action Updates bad sector information stored on disk directory track.
  • Page 337 Section 060-INDP-410 Command and Message Guide 4-177 Table 7-106 DISK: REASSIGN SCHEDULED message 1 9 3 DISK: REASSIGN SCHEDULED Cause: this message follows a DISK: COMMAND ERROR message. The bad sector relocation has been Display: Log message scheduled for relocation on the disk. Relocation begins during a period of low, or no disk activity.
  • Page 338 4-178 Section 060-INDP-410 Command and Message Guide Table 7-107 DISK: RST-7 message 2 0 1 Customer-Selected Alarm Level Type:Level: 2 0 2 Other Alarm Indications Default: Status Panel:MinorAudible:Minor Customer-Selected Status Panel:Audible: 2 0 3 System Recovery Action Disk system restarts task. 2 0 4 Craftsperson Activity: If this message is seen more than once, replace the...
  • Page 339 Section 060-INDP-410 Command and Message Guide 4-179 Table 7-108 DISK: x FAILURE message 2 0 8 Other Alarm Indications Default: Status Panel:MajorAudible:Major Customer-Selected Status Panel:Audible: 2 0 9 System Recovery Action Processor Switch 2 1 0 Craftsperson Activity: If this message is seen more than once, replace the SCSI Interface PCA using the Miscellaneous PCA Replacement Procedure in the Maintenance Procedures Guide section.
  • Page 340 (DMA status report). Note: In the event that the value of the command byte (as listed above) indicates a faulty condition, record the values for use in conjunction with Nortel field service personnel in the trouble shooting efforts. 2 1 8...
  • Page 341 Section 060-INDP-410 Command and Message Guide 4-181 Table 7-110 DMA TIME OUT ALARM message 2 2 1 System Recovery Action None 2 2 2 Craftsperson Activity: Refer to the TEC/DSI PCA Diagnostic Procedure in the Maintenance Procedures Guide section . Table 7-111 DOWNLOAD REQUESTED message 2 2 3...
  • Page 342 4-182 Section 060-INDP-410 Command and Message Guide Table 7-112 DPR TEST FAILED message 2 2 9 (log message) Where: DPR TEST FAILED xxxx = DPR address where the fault occurred (in Hex). ADR:xxxx RD:yy WR:zz yy = incorrect value read from memory (in Hex). zz = expected value that was written to memory (in Display: Maintenance terminal Hex).
  • Page 343 Section 060-INDP-410 Command and Message Guide 4-183 Table 7-113 DPR TEST NOT SUPPORTED message 2 3 5 DPR TEST NOT SUPPORTED Cause: a DPR test is normally conducted automatically at 10 before the hour, each hour of the day. This test is Display: Maintenance terminal conducted in order to verify that communication is possible with the SCSI Interface.
  • Page 344 4-184 Section 060-INDP-410 Command and Message Guide Table 7-114 D-RAM ERROR xx AT yyyy message 2 4 1 (log message) Where: D-RAM ERROR xx AT yyyy xx = interrupt register value (page number, hi bit is parity bit). Display: Log message yyyy = next program address to be executed.
  • Page 345 Section 060-INDP-410 Command and Message Guide 4-185 Table 7-115 DSK MSG xx: message DSK MSG xx: Where: xx = cross-references to software message(s). These responses appear during disk activities in the monitor mode. System software is not running. 00 = MSG RCVD PARM DISK 02 = WRT MEM COMPLETE 04 = OUTPUT COMPLETE 0B = RST-7 0C = QTY BAD TRACKS...
  • Page 346 4-186 Section 060-INDP-410 Command and Message Guide Table 7-116 EC-CF-ALM message (log message) Cause: output after a conflict in error control EC-CF-ALM commands. A conflict can occur when both processors (Error Control-Conflict-Alarm) are in the same state (both active or both standby). Display: Log message Alarm Level: Reason Code = 14...
  • Page 347 Section 060-INDP-410 Command and Message Guide 4-187 Table 7-117 EC-IC-ALM message (log message) Cause: output automatically after an illegal error control EC-IC-ALM command. (Error Control-Illegal Command- Alarm) Display: Log message Alarm Level: Reason Code = 18 No processor switch Corresponds to ERRMAP entry: ERROR CTL INCON System Default: Type:MajorLevel:0 Customer-Selected Alarm Level...
  • Page 348 4-188 Section 060-INDP-410 Command and Message Guide Table 7-118 ERROR DETECTED ON PROC x message (log message) Cause: message displayed in response to the TEST ERROR DETECTED ON PROC x (keyboard entry) command, where the BMC processor detects a problem with one or more of the PCAs. (This Display: Log message message is accompanied by a card entry message, listing the potential assembly failures.)
  • Page 349 Section 060-INDP-410 Command and Message Guide 4-189 Table 7-119 ERROR OPENING ACTIVE FILE message (log message) Cause: indicates that the Active Call Record file ERROR OPENING ACTIVE FILE contained within the Active File Table cannot be opened. Display: Log message Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A...
  • Page 350 4-190 Section 060-INDP-410 Command and Message Guide Table 7-120 ERROR READING CALL RECORDS message Other Alarm Indications Default: Status Panel:MajorAudible:Major Customer-Selected Status Panel:Audible: System Recovery Action Determined by associated disk error messages. Craftsperson Activity: Refer to the associated disk error messages. Table 7-121 EXCESSIVE INVALID BLOCKS message (log message)
  • Page 351 Section 060-INDP-410 Command and Message Guide 4-191 Table 7-122 EXCESSIVE INVALID RECORDS message (log message) Cause: exception report printed whenever the daily EXCESSIVE INVALID RECORDS count of invalid call records reaches the threshold value specified by the VALPARM INVALID site data entry. Display: Log message Alarm Level: Reason Code = 26...
  • Page 352 4-192 Section 060-INDP-410 Command and Message Guide Table 7-123 FALSE DMA INTERRUPT message Other Alarm Indications Default: Status Panel:MajorAudible:Major Customer-Selected Status Panel:Audible: System Recovery Action May cause a processor switch. Replace the CPU PCA using the Miscellaneous PCA Craftsperson Activity: Replacement Procedure in the Maintenance Procedures Guide section.
  • Page 353 Section 060-INDP-410 Command and Message Guide 4-193 Table 7-125 FILE BUSY, TRY AGAIN message FILE BUSY, TRY AGAIN Cause: response to an IDXMAINT EXAMINE or IDXMAINT SUMMARY command while the file is Display: Maintenance terminal temporarily unavailable. Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A System Default: Type:N/ALevel:N/A...
  • Page 354 0. Display: Log message This output should not appear during normal operation; used by Nortel for test and verification purposes only. Ignore this message if it appears when changing TEC/ DSI PCAs or removing TEC/DSI cables. Alarm Level:...
  • Page 355 DISK FORMAT A (or B) Display: Maintenance terminal command. Note: The DISK FORMAT x command is used in extreme emergencies ONLY and then under the direction of the Nortel Technical Support personnel. Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A...
  • Page 356 4-196 Section 060-INDP-410 Command and Message Guide Table 7-129 FORMAT IN PROGRESS message FORMAT IN PROGRESS Cause: output if the DISK FORMAT x or DISK MODE x command is entered and either disk is currently being Display: Maintenance terminal formatted. Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A...
  • Page 357 Note: Use the DISK FORMAT x command only in extreme emergencies and then only under the direction of Nortel field support. Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A...
  • Page 358 4-198 Section 060-INDP-410 Command and Message Guide Table 7-131 ILLEGAL COMMAND message 1 0 3 ILLEGAL COMMAND Cause: firmware message that responds, when: Display: Maintenance terminal a. user enters a command that was not recognized by the system. b. user has an insufficient priority level to use the command.
  • Page 359 Section 060-INDP-410 Command and Message Guide 4-199 Table 7-132 ILLEGAL DISK MODE CHANGE REQUEST message 1 0 9 ILLEGAL DISK MODE CHANGE Cause: output in response to DISK MODE command REQUEST when requested mode change is illegal. Message is output whenever one of the following disk mode Display: Maintenance terminal changes is requested: A ONLY to A ONLYB ONLY to B ONLY...
  • Page 360 4-200 Section 060-INDP-410 Command and Message Guide Table 7-133 ILLEGAL PASSWORD message 1 1 5 ILLEGAL PASSWORD Cause: output when the user does not include the proper six alphanumeric characters of a password in an Display: Maintenance terminal attempt to enter a new password into the BMC. 1 1 6 Alarm Level: Reason Code = N/A...
  • Page 361 Section 060-INDP-410 Command and Message Guide 4-201 Table 7-134 ILLEGAL PRIORITY message 1 2 3 Customer-Selected Alarm Level Type:Level: 1 2 4 Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: 1 2 5 System Recovery Action None; input is rejected 1 2 6 Craftsperson Activity: Refer to the associated command subsections in this...
  • Page 362 4-202 Section 060-INDP-410 Command and Message Guide Table 7-136 ILLEGAL USER NUMBER message 1 3 3 ILLEGAL USER NUMBER Cause: output in response to the PSWD command when a specified user number in a command does not Display: Maintenance terminal exist in the password list.
  • Page 363 Section 060-INDP-410 Command and Message Guide 4-203 Table 7-137 IMPROPER FILE TYPE message 1 4 1 Customer-Selected Alarm Level Type:Level: 1 4 2 Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: 1 4 3 System Recovery Action Requested action is terminated. 1 4 4 Craftsperson Activity: Reenter the command with the proper file type (AMA, or...
  • Page 364 4-204 Section 060-INDP-410 Command and Message Guide Table 7-138 IMPROPER FORMAT TYPE message 1 4 9 System Recovery Action None 1 5 0 Craftsperson Activity: Refer to the IDXMAINT command section of this document for the correct syntax. Reenter the command with a valid format type.
  • Page 365 Section 060-INDP-410 Command and Message Guide 4-205 Table 7-140 IMPROPER LINK DISCONNECT: TIMEOUT message 1 5 7 IMPROPER LINK DISCONNECT: Cause: output when the BMC tries to become the TIMEOUT “talker”, but does not get a response from the HOC after 12 attempts.
  • Page 366 4-206 Section 060-INDP-410 Command and Message Guide Table 7-141 INCOMING CALL REJECTED nn message 1 6 3 (log message) Where: nn = reason for call rejection: INCOMING CALL REJECTED nn 01 = remote station password rejected. 02 = local password rejected. Display: Log message Cause: output to indicate that the remote station request to set up a data link was denied due to a...
  • Page 367 Section 060-INDP-410 Command and Message Guide 4-207 Table 7-142 INPUT BLOCK CHECKSUM ERROR message 1 6 9 INPUT BLOCK CHECKSUM Cause: output when a call record block record block ERROR received from the Switching System is in error. Display: Log message 1 7 0 Alarm Level: Reason Code = N/A...
  • Page 368 4-208 Section 060-INDP-410 Command and Message Guide Table 7-143 INVALID ADDR message 1 7 8 Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: 1 7 9 System Recovery Action BMC attempts to reboot software three times, then aborts, leaving BMC without active software. 1 8 0 Craftsperson Activity: Refer to the Boot Recovery Procedure in the...
  • Page 369 Section 060-INDP-410 Command and Message Guide 4-209 Table 7-145 INVALID CALL RECORD FORMAT message 1 8 7 INVALID CALL RECORD Cause: output for the following reasons: FORMAT a. call record received from the Switching System is not Display: Log message a valid LSSGR billing call record.
  • Page 370 4-210 Section 060-INDP-410 Command and Message Guide Table 7-146 INVALID NUMBER ENTERED message 1 9 3 INVALID NUMBER ENTERED Cause: output in response to an IDXMAINT EXAMINE or IDXMAINT CREATE DIR keyboard command when Display: Maintenance terminal a numerical field is entered incorrectly. 1 9 4 Alarm Level: Reason Code = N/A...
  • Page 371 Section 060-INDP-410 Command and Message Guide 4-211 Table 7-147 INVALID RANGE message 2 0 2 Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: 2 0 3 System Recovery Action None. 2 0 4 Craftsperson Activity: Refer to the AMAHRS command section of this document for the correct syntax.
  • Page 372 4-212 Section 060-INDP-410 Command and Message Guide Table 7-149 INVALID SLGRP: EMBEDDED COMMAND IGNORED message 2 1 1 INVALID SELGRP: EMBEDDED Cause: output in response to Secondary AMA data poll COMMAND IGNORED request from the HOC. Indicates that the poll request failed when an invalid SELGRP command value Display: log message (greater than six) was sent in the Secondary AMA data...
  • Page 373 Section 060-INDP-410 Command and Message Guide 4-213 Table 7-150 INVALID SITE DATA FILE message 2 1 7 INVALID SITE DATA FILE Cause: output when the site data file read from disk is rejected because it is the wrong size. Display: Log message 2 1 8 Alarm Level: Reason Code = 14...
  • Page 374 4-214 Section 060-INDP-410 Command and Message Guide Table 7-151 IPCOM LOAD ERROR message 2 2 5 Customer-Selected Alarm Level Type:Level: 2 2 6 Other Alarm Indications Default: Status Panel:MajorAudible:Major Customer-Selected Status Panel:Audible: 2 2 7 System Recovery Action System make three attempts to load. 2 2 8 Refer to the Boot Recovery Procedure in the Craftsperson Activity:...
  • Page 375 Section 060-INDP-410 Command and Message Guide 4-215 Table 7-152 KERNEL SERVICE ERROR - xxx message 2 3 1 Customer-Selected Alarm Level Type:Level: 2 3 2 Other Alarm Indications Default: Status Panel:N/AAudible:N/A Customer-Selected Status Panel:Audible: 2 3 3 System Recovery Action Polling may be affected by the error condition that caused the message to print.
  • Page 376 4-216 Section 060-INDP-410 Command and Message Guide Table 7-153 KEY COMMAND NOT AVAILABLE message 2 3 5 KEY COMMAND NOT AVAILABLE Cause: output when: Display: Maintenance terminal a. firmware keyboard command is entered when an equivalent software command is available. (Software is running in the BMC system.) b.
  • Page 377 Section 060-INDP-410 Command and Message Guide 4-217 Table 7-154 KEY “SETCLK”, THEN ENTER DATE, TIME, AND DAY message 2 4 1 KEY “SETCLK”, THEN ENTER Cause: output when the clock data fields do not contain DATE, TIME, AND DAY valid values, such as at system power-up. Display: Maintenance terminal a.
  • Page 378 4-218 Section 060-INDP-410 Command and Message Guide Table 7-155 LAST GOOD #xxxxxx, GOT #yyyyyy message 2 4 7 LAST GOOD #xxxxxx, GOT #yyyyyy where: xxxxxx = sequence number of the last valid AMA block Display: Maintenance terminal retrieved from DPR. yyyyyy = sequence number of the block received is out of sequence or BMC has already received another block with that sequence number.
  • Page 379 Section 060-INDP-410 Command and Message Guide 4-219 Table 7-156 LINK DISCONNECTED message 2 5 3 LINK DISCONNECTED Cause: output when an HOC-to-BMC Session has ended. Display: Log message 2 5 4 Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A System Default: Type:N/ALevel:N/A 2 5 5...
  • Page 380 4-220 Section 060-INDP-410 Command and Message Guide Table 7-157 LINK TRANSMIT WINDOW message 2 6 1 Customer-Selected Alarm Level Type:Level: 2 6 2 Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: 2 6 3 System Recovery Action Link is terminated by the BMC. 2 6 4 If seen repeatedly, refer to the Polling Diagnostic Craftsperson Activity:...
  • Page 381 Section 060-INDP-410 Command and Message Guide 4-221 Table 7-159 LOG FILE DELETED message 2 7 1 (log message) Cause: output when the LOG files are deleted to make LOG FILE DELETED room for primary AMA files; occurs when disk usage percentage reaches 90% and when the files DA TO Display: Log message DLET value has reached 0.
  • Page 382 4-222 Section 060-INDP-410 Command and Message Guide Table 7-160 MPSR ERR message 2 7 9 Customer-Selected Alarm Level Type:Level: 2 8 0 Other Alarm Indications Default: Status Panel:N/AAudible:N/A Customer-Selected Status Panel:Audible: 2 8 1 System Recovery Action Session is terminated. 2 8 2 Craftsperson Activity: If the problem persists, contact your next level of...
  • Page 383 Note: In the event that the values (as listed above) indicate a faulty condition, record the values for use in conjunction with Nortel field service personnel in the trouble shooting efforts. BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 384 4-224 Section 060-INDP-410 Command and Message Guide Table 7-162 MTUxx: CMD-yy, STA-zz, BLK-aaaa message 2 9 0 Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A System Default: Type:N/ALevel:N/A 2 9 1 Customer-Selected Alarm Level Type:Level: 2 9 2 Other Alarm Indications Default: Status Panel:Audible:...
  • Page 385 Section 060-INDP-410 Command and Message Guide 4-225 Table 7-163 NO BLOCK LAST ii MINUTES message 2 9 8 Other Alarm Indications Default: Status Panel:MinorAudible:Minor Customer-Selected Status Panel:Audible: 2 9 9 System Recovery Action Alarm, no processor switch. 3 0 0 Craftsperson Activity: Verify traffic/AMA data level in Switching System is at least one block per ii minutes.
  • Page 386 (No Command) Display: Log message This output should not appear during normal operation; used by Nortel for test and verification purposes only. Ignore this message if it appears when changing TEC/ DSI PCAs or removing TEC/DSI cables. 3 0 8...
  • Page 387 Section 060-INDP-410 Command and Message Guide 4-227 Table 7-166 NO DATA AVAILABLE message 3 1 3 NO DATA AVAILABLE Cause: output when the sequence number requested by the HOC in the polling request is not present within Display: Maintenance terminal the index for the embedded SELGRP setting.
  • Page 388 4-228 Section 060-INDP-410 Command and Message Guide Table 7-167 NO DISK ON LINE message 3 1 9 (log message) Cause: output when a disk job attempts to select the NO DISK ON LINE PRIME or STANDBY disk drive unit before either of the disk drive unit(s) have been put on-line.
  • Page 389 Section 060-INDP-410 Command and Message Guide 4-229 Table 7-168 NO FILE AVAILABLE message 3 2 8 Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: 3 2 9 System Recovery Action None 3 3 0 Craftsperson Activity: Refer to the description of the IDXMAINT CREATE FILE command in this document.
  • Page 390 4-230 Section 060-INDP-410 Command and Message Guide Table 7-170 NO S/W ON DISK message 3 3 7 NO S/W ON DISK Cause: output when a program boot from disk failed when the following events occur: Display: Log message a. system cannot find one of the files entered in the boot list.
  • Page 391 Section 060-INDP-410 Command and Message Guide 4-231 Table 7-171 NO SECNDRY FILES TO DELETE message (log message) Cause: output when no secondary files can be deleted NO SECNDRY FILES TO DELETE to make room for primary files. Occurs when the disk(s) are over 70 percent full.
  • Page 392 (No Select) (USEL). Display: Log message This output should not appear during normal operation; used by Nortel for test and verification purposes only. Ignore this message if it appears when changing TEC/ DSI PCAs or removing TEC/DSI cables. Alarm Level:...
  • Page 393 Section 060-INDP-410 Command and Message Guide 4-233 Table 7-173 NO SITE DATA ON DISK message NO SITE DATA ON DISK Cause: output when an attempt to read or write site data to RAM is made, but the file does not exist. Display: Log message Alarm Level: Reason Code = N/A...
  • Page 394 4-234 Section 060-INDP-410 Command and Message Guide Table 7-174 NO SUCH KEYBOARD COMMAND message Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: System Recovery Action None Craftsperson Activity: Refer to the MPRI command subsection. Table 7-175 OFFLINE DISK FULL message OFFLINE DISK FULL Cause: output when the standby disk is full.
  • Page 395 Section 060-INDP-410 Command and Message Guide 4-235 Table 7-176 OFF-LINE DISK HAS UNPOLLED DATA message (log message) Cause: when the BMC disk system becomes filled up OFF-LINE DISK HAS UNPOLLED with call record data while in a PRIME disk mode, the DATA standby disk automatically goes to off-line mode.
  • Page 396 4-236 Section 060-INDP-410 Command and Message Guide Table 7-177 ONLY MODE NON-REDUNDANT x message ONLY MODE NON-REDUNDANT x Where: x = A or B processor (A or B). Display: Log message Cause: output when the user has manually switched the system to processor x in the ONLY mode. Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: ONLY NON-REDUND...
  • Page 397 Section 060-INDP-410 Command and Message Guide 4-237 Table 7-178 PARITY ERROR: x DETECTED message PARITY ERROR: x DETECTED Where: x = indicate which side detected the error. = SCSI Interface Display: Log message = MP Cause: output whenever a parity error is detected by the MP in DPR, or by SCSI Interface in DPR or PRAM.
  • Page 398 4-238 Section 060-INDP-410 Command and Message Guide Table 7-179 PASSWORD ALREADY EXISTS message PASSWORD ALREADY EXISTS Cause: output in response to the PSWD command, when the user tries to add a password that already Display: Maintenance terminal exists in the password list. Alarm Level: Reason Code = N/A Corresponds to ERRMAP entry: N/A...
  • Page 399 Section 060-INDP-410 Command and Message Guide 4-239 Table 7-180 PASSWORD DOES NOT EXIST message Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: System Recovery Action None. Craftsperson Activity: Verify PSWDL to determine the current passwords. Table 7-181 PASSWORD TABLE FULL message PASSWORD TABLE FULL Cause: output in response to the PSWD command when the user attempts to add a password when the...
  • Page 400 4-240 Section 060-INDP-410 Command and Message Guide Table 7-182 POLLING IN PROCESS message POLLING IN PROCESS Cause: output in response to the IDXMAINT EXAMINE FILE keyboard (command) request, when: Display: Maintenance terminal a. call record polling is under way. b. an attempt is made to read from a new file before the last file is closed.
  • Page 401 Section 060-INDP-410 Command and Message Guide 4-241 Table 7-183 PROG CHKSUM ALM VAL = nn message (log message) Where: nn = difference from 0 of the calculated PROG CHKSUM ALM VAL = nn checksum Display: Log message Cause: output when a program memory verification has failed for a downloaded program.
  • Page 402 4-242 Section 060-INDP-410 Command and Message Guide Table 7-184 PROLONGED FILE BUSY CLEARED message PROLONGED FILE BUSY Cause: output when a disk file busy flag has been set CLEARED for about 10 seconds following the input of an AMA data block.
  • Page 403 Section 060-INDP-410 Command and Message Guide 4-243 Table 7-185 PROM CHKSUM ALM VAL = nn message (log message) Where: nn = difference from 0 of the calculated PROM CHKSUM ALM VAL = nn checksum Display: Log message Cause: output when a PROM program memory verification has failed.
  • Page 404 4-244 Section 060-INDP-410 Command and Message Guide Table 7-186 PURCHASED CAPACITY NOT AVAILABLE message (log message) Cause: output when the amount of storage capacity (in PURCHASED CAPACITY NOT Logical Blocks) on the disk drive does not meet the AVAILABLE minimum requirements to support the software. Display: Log message Alarm Level: Reason Code = 0...
  • Page 405 Section 060-INDP-410 Command and Message Guide 4-245 Table 7-187 RAM TEST FAILED message 1 0 5 Customer-Selected Alarm Level Type:Level: 1 0 6 Other Alarm Indications Default: Status Panel:MajorAudible:Major Customer-Selected Status Panel:Audible: 1 0 7 System Recovery Action Processor switch. 1 0 8 Refer to the DRAM PCA Diagnostic Procedure in the Craftsperson Activity:...
  • Page 406 4-246 Section 060-INDP-410 Command and Message Guide Table 7-189 SCSI: INTERRUPT FROM INVALID DEVICE message 1 1 5 SCSI: INTERRUPT FROM Cause: the SCSI Controller received an interrupt from INVALID DEVICE an invalid source. Probably caused by an incorrectly strapped disk drive. Display: Log message 1 1 6 Alarm Level:...
  • Page 407 Section 060-INDP-410 Command and Message Guide 4-247 Table 7-190 SCSI: INTERRUPT WHILE IDLE message 1 2 3 Customer-Selected Alarm Level Type:Level: 1 2 4 Other Alarm Indications Default: Status Panel:MinorAudible:Minor Customer-Selected Status Panel:Audible: 1 2 5 System Recovery Action None. 1 2 6 Craftsperson Activity: Verify the disk drive strapping.
  • Page 408 4-248 Section 060-INDP-410 Command and Message Guide Table 7-191 SDI COM FAIL message 1 3 1 System Recovery Action None 1 3 2 a. Verify the value of the password set in the DMSP Craftsperson Activity: command. b. If the value of the password is correct, contact the next level of support to resolve a communication problem.
  • Page 409 Section 060-INDP-410 Command and Message Guide 4-249 Table 7-192 >> SET CLOCK << message 1 3 7 System Recovery Action None 1 3 8 a. Set the system clock using the SETCLK command. Craftsperson Activity: Refer to the SETCLK subsection for more information.
  • Page 410 4-250 Section 060-INDP-410 Command and Message Guide Table 7-193 STANDBY PROC NOT AVAILABLE message 1 4 3 System Recovery Action None 1 4 4 Craftsperson Activity: Verify the Status Panel rockers. If the rockers are set to O and the ONL lamp is lit, determine whether troubleshooting is in progress.
  • Page 411 Section 060-INDP-410 Command and Message Guide 4-251 Table 7-195 STRCT CODE INDEX OUT OF RANGE message 1 5 1 SRTCT CODE INDEX OUT OF Cause: structure code generated by the Switching RANGE System is not supported by the BMC system. Display: Log message 1 5 2 Alarm Level:...
  • Page 412 4-252 Section 060-INDP-410 Command and Message Guide Table 7-196 TAPE BLOCKS LOST = xxx message 1 5 7 (log message) Where: xxx = number of tape blocks lost (at the TEC/ TAPE BLOCKS LOST = xxx DSI PCA). Display: Log message Cause: output when AMA tape data block(s) are lost.
  • Page 413 Section 060-INDP-410 Command and Message Guide 4-253 Table 7-197 TEC BUFFER OVERFLOW: xx BLOCKS message 1 6 3 (log message) Where: xx = number of blocks not yet processed and TEC BUFFER OVERFLOW: xx overwritten by new blocks from the TEC/DSI PCA, BLOCKS when no empty buffers are available.
  • Page 414: Tec/Dsi Pca Diagnostic

    4-254 Section 060-INDP-410 Command and Message Guide Table 7-198 TIME OUT message 1 6 9 TIME OUT Cause: output as part of an error message when a disk command is not successfully executed within an Display: Maintenance terminal allocated time period. 1 7 0 Alarm Level: Reason Code = N/A...
  • Page 415 Section 060-INDP-410 Command and Message Guide 4-255 Table 7-199 UNINITIALIZED SYSTEM OR BAD DISK message 1 7 5 UNINITIALIZED SYSTEM OR BAD Cause: output in response to a request to change disk DISK mode from an ONLY mode to a PRIME mode when the off-line disk is uninitialized.
  • Page 416 4-256 Section 060-INDP-410 Command and Message Guide Table 7-200 UNKNOWN DISK MESSAGE xx message 1 8 1 UNKNOWN DISK MESSAGE xx Where: xx = message ID (in hex - 00-FF) Display: Log message Cause: output whenever a message ID is received by the MP from the SCSI Interface that is invalid.
  • Page 417 Section 060-INDP-410 Command and Message Guide 4-257 Table 7-201 UNSUPPORTED STRCT CODE xxxxxx message 1 8 7 (log message) Where: xxxxxx - structure code value UNSUPPORTED STRCT CODE xxxxxx Cause: structure code generated by the Switching System is not supported by the BMC system. Display: Log message 1 8 8 Alarm Level:...
  • Page 418 4-258 Section 060-INDP-410 Command and Message Guide Table 7-202 VERSION POOL EXHAUSTED message 1 9 3 VERSION POOL EXHAUSTED Cause: output when the number of versions of a file type (AMA or LOG) reaches 200. Display: Log message 1 9 4 Alarm Level: Reason Code = 2B Corresponds to ERRMAP entry: DSK STORE LIMIT...
  • Page 419 (Wrong Command) This output should not appear during normal operation; Display: Log message used by Nortel for test and verification purposes only. Ignore this message if it appears when changing TEC/ DSI PCAs or removing TEC/DSI cables. 2 0 0...
  • Page 420 4-260 Section 060-INDP-410 Command and Message Guide Table 7-204 WRITE TO DISK FAILED message 2 0 5 WRITE TO DISK FAILED Cause: a failure occurred when trying to write a block to disk during a download session. Display: Log message 2 0 6 Alarm Level: Reason Code = N/A...
  • Page 421 Section 060-INDP-410 Command and Message Guide 4-261 Table 7-205 xx BLKS NOT UPDATED message 2 1 1 (log message) Where: xx = excess block count. xx BLKS NOT UPDATED Cause: output when the update count (number of call Display: Log message record blocks sent) exceeds the number of call record blocks on disk remaining to be polled.
  • Page 422 4-262 Section 060-INDP-410 Command and Message Guide Table 7-206 xx SIO TEST FAILED message 2 1 7 A2 SIO TEST FAILED Where: xx = port definition: A4 SIO TEST FAILED A2 =communications port; Modem/HOC link. A6 SIO TEST FAILED (download link and first polling link) A4 =maintenance port;...
  • Page 423 Section 060-INDP-410 Command and Message Guide 4-263 Table 7-207 xxx DUPLICATE BLOCKS REJECTED message 2 2 3 (log message) Where: xxx = number of blocks rejected. xxx DUPLICATE BLOCKS REJECTED Cause: during the screening process performed by the BMC (on all outgoing call record blocks to the HOC), a Display: Log message block sequence number was of lower numerical value than the one preceding it.
  • Page 424 4-264 Section 060-INDP-410 Command and Message Guide Table 7-208 xxxIDX FILE FAILURE message 2 2 9 AMAIDX FILE FAILURE Cause: output when an attempt to update a record LOGIDX FILE FAILURE index file fails. Display: Maintenance terminal 2 3 0 Alarm Level: Reason Code = 03 Processor switch occurs...
  • Page 425 Section 060-INDP-410 Command and Message Guide 4-265 Table 7-209 xxxIDX FILE FULL message 2 3 5 (log message) Cause: the index file designated contains 200 versions AMAIDX FILE FULL and an attempt is made to create another xxxCRD file. (log message) LOGIDX FILE FULL Display: Log message 2 3 6...
  • Page 426 4-266 Section 060-INDP-410 Command and Message Guide Table 7-210 xxxIDX FILE OPEN ERROR : 03 message 2 4 1 (log message) Cause: disk file error message that is output when a AMAIDX FILE OPEN ERROR : 03 disk file operation could not open an index file. (log message) LOGIDX FILE OPEN ERROR : 03 Display: Log message...
  • Page 427 Section 060-INDP-410 Command and Message Guide 4-267 Table 7-211 xxx SEQ #yyyyyy NOT IN FILE message 2 4 7 AMA SEQ #yyyyyy NOT IN FILE Where: yyyyyy= Sequence Number (0-999999) LOG SEQ #yyyyyy NOT IN FILE Cause: response to IDXMAINT EXAMINE or Display: Maintenance terminal IDXMAINT CREATE DIR keyboard request, when a sequence number for specified file type cannot be...
  • Page 428 4-268 Section 060-INDP-410 Command and Message Guide Table 7-212 xxx WRITE FILE CLOSED message 2 5 3 AMA WRITE FILE CLOSED Cause: output when the current data write file is closed, LOG WRITE FILE CLOSED using the IDXMAINT CREATE FILE command or during polling.
  • Page 429 Section 060-INDP-410 Command and Message Guide 4-269 Table 7-213 xxxxxx DOWNLOAD ABORTED message 2 6 1 Customer-Selected Alarm Level Type:Level: 2 6 2 Other Alarm Indications Default: Status Panel:Audible: Customer-Selected Status Panel:Audible: 2 6 3 System Recovery Action None 2 6 4 Craftsperson Activity: Contact the next level of support.
  • Page 430 4-270 Section 060-INDP-410 Command and Message Guide Table 7-214 xxxxxx FILE yyyyyy ERROR: ee message = 00 = indicates file is closed = 01 = directory full = 02 = active file table full = 03 = no such file = 04 = file not closed = 05 = file not open...
  • Page 431 Section 060-INDP-510 System Operation Guide The BMC is designed to be a fully-automatic device that provides storage of call record data. The BMC acquires data from the Switching System through a Magnetic Tape Port (MTP) and emulates all communication and control signals expected by the Switching System.
  • Page 432 TEC/DSI part of Controller SCSI Interface SCSI Inter- Switch- EPROM part of Inter- Controller DRAM ER CL P/A COMM DMS-10 - MTC PTR1 Quad SIO SCSI DMS-100 - MTC PTR1 Cross- A15/B15 A6/A7 Inter DMS-10 - SDI Port Proces- DMS-100 - MTC PTR2 Quad SIO SCSI Interface SCSI...
  • Page 433 Section 060-INDP-510 System Operation Guide 5-3 The automatic operation of the BMC means that little user intervention is required. To provide greater understanding of operation, the transfer of data from the Switching System, the translation for intermediate storage, the polling of data to the HOC, and maintenance communications are described in this section.
  • Page 434 5-4 Section 060-INDP-510 System Operation Guide Note: TEC PCAs are found in BMC systems configured for use with DMS-10 Switching Systems. DSI PCAs are found in BMC systems configured for use with DMS-100 Switching Systems. BMC II System RAM When the Switching System transmits data blocks, a signal is sent to the active processor to accept the block.
  • Page 435 Section 060-INDP-510 System Operation Guide 5-5 PCA is presented to the Disk Controller in the Disk Drive Assemblies in a form which can be handled by the disk drives. The SCSI Interface PCAs are intermediaries between RAM and the Disk Drive Assemblies. The Disk Controllers control the location and labeling of call record data blocks on each disk.
  • Page 436 5-6 Section 060-INDP-510 System Operation Guide Table 8-1 BMC file names File File Contents Name TDYSTS Contains maintenance and statistical data concerning BMC unit operation. YDYSTS Program Contain the BMC unit program files. Files Sheet 2 of 2 To guard against data loss in the event of a loss of power, new AMA data is temporarily written to disk every minute.
  • Page 437 Section 060-INDP-510 System Operation Guide 5-7 schedules are a function of the expected traffic at the various CO sites. The HOC can request status, a file transfer, or abort the session. All of these activities must be initiated by the HOC. BMC Communication The HOC initiates remote operation through a modem over either dial-up or dedicated lines.
  • Page 438 The second link provides maintenance access via SDI port (DMS-10 only). There is a third link on the Quad SIO PCA that is used for program download by Nortel. Like the modem links, the printer communication path connects the printer to the Power and Alarm Communications PCA before reaching the Quad SIO PCA.
  • Page 439 Section 060-INDP-610 Maintenance Procedures Guide The following paragraphs provide the instructions for the use of this section. This section is divided into the following subsections: • Equipment Description • Routine Maintenance Procedures • Diagnostic Procedures. • Hardware Replacement. The Equipment Description subsection provides a general listing of the overall physical structure of the BMC.
  • Page 440 6-2 Section 060-INDP-610 Maintenance Procedures Guide Table 6-1 List of assemblies and subassemblies Reference ABBR Full name - part number - usage notes designat name BMC II Billing Media Converter II (system) (1) NT8M01GC - BMC BISYNC with 1-GB disk drives for DMS-10 (2) NT8M04GC - BMC BISYNC with 1-GB disk drives for DMS-100 A Processor (Upper) Chassis - N/A Central Processor Unit Logic w/DMA PCA - NT6M62BA...
  • Page 441 Section 060-INDP-610 Maintenance Procedures Guide 6-3 Table 6-1 List of assemblies and subassemblies Reference ABBR Full name - part number - usage notes designat name SCSI SCSI Crossover PCA (located on inner portion of hinged panel at rear XOVR of upper chassis) - NT6M93BA Power and Alarm Communications PCA (located on the outer portion COMM of hinged panel at rear of upper chassis) - NT6M84BA...
  • Page 442 6-4 Section 060-INDP-610 Maintenance Procedures Guide Table 6-1 List of assemblies and subassemblies Reference ABBR Full name - part number - usage notes designat name QUAD Quad Serial Input/Output PCA - NT6M60BA 56K Interface PCA - NT6M94AA INTF SCSI SCSI Interface PCA - NT6M66CA INTF B12 &...
  • Page 443 Section 060-INDP-610 Maintenance Procedures Guide 6-5 Table 6-1 List of assemblies and subassemblies Reference ABBR Full name - part number - usage notes designat name DISK Disk Drive Assembly - NT6M72GA a. 3 1/2” disk drive with a 1-Gbyte capacity b.
  • Page 444 6-6 Section 060-INDP-610 Maintenance Procedures Guide PCA Locations Subassembly and PCA locations are listed in Table 6-1 and illustrated in Figure 6-1. The illustration shows that two PCA racks (A and B) are used. PCAs designated A1 through A14 are in the A (upper) chassis; B1 through B14 are in the B (lower) chassis.
  • Page 445 Section 060-INDP-610 Maintenance Procedures Guide 6-7 Figure 3-1 BMC cabinet subassemblies Processor A Switch and Circuit Boards Status Panel A1-----------------------A14 Processor A chassis A20 Power Supply A21 Disk Drive A B20 Power Supply B21 Disk Drive B Processor B chassis B1------------------------B14 Filler Panel Processor B...
  • Page 446 6-8 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 Auxiliary circuit assembly locations Left rear of chassis (with cabinet back removed) Hinged card panel (closed) Power and Alarm Communications PCA (A16) or 56K Crossover PCA (B16) a. View with hinged card panel closed SCSI Crossover PCA (A15 and B15) (opposite side of hinged panel)
  • Page 447 Section 060-INDP-610 Maintenance Procedures Guide 6-9 Figure 3-1 Disk Drive Assembly Retainer Screw Extraction handle Rear Retainer Screw Top view Extraction handle Do not remove Retainer Front View Side View screw reference BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 448 The solid state lamps provide long trouble-free oper- ation. Replacement status and alarm lamps should be ordered through Nortel. Refer to Table 6-2 for more information.
  • Page 449 Section 060-INDP-610 Maintenance Procedures Guide 6-11 Figure 3-1 BMC Switch and status panel Switch and Status Panel CRIT CHAS. GND. Filler Panel CHAS. GND. LEGEND: A Processor Status Lamps System Status Lamps ALM = Alarm CRIT = Critical = PRIME Mode MAJ = Major ONL = ONLY Mode MIN = Minor...
  • Page 450 6-12 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 Removing BMC system front panel Thumb Thumb Screws: Screws: Loosen Loosen, Do Not Do Not Remove Remove Thumb Thumb Screws: Screws: Loosen, Loosen, Do Not Do Not Remove Remove 297-6201-502 Standard 01.02 September 2000...
  • Page 451 Section 060-INDP-610 Maintenance Procedures Guide 6-13 Status and Alarm Lamp Replacement Procedure 6-1 Status and Alarm Panel lamp test and replacement Step Description CAUTION It is recommended that Status and Alarm lamp replacement be performed by qualified maintenance personnel. Remove the front panel of the BMC, A chassis. Refer to Figure 6-5. Note which lamps are already lit.
  • Page 452 6-14 Section 060-INDP-610 Maintenance Procedures Guide to the Switching System. The Switching System interprets the alarm bit as an indication that the active recording volume, disk drive, is full. The Switching System switches the standby volume (to the other TEC/DSI PCA) to the active position and continues sending AMA to the BMC.
  • Page 453 Section 060-INDP-610 Maintenance Procedures Guide 6-15 Procedure 6-2 System low voltage alarm Step Description Remove the rear panel of the A chassis by taking out the eight screws that secure the panel to the chassis. Once removed, put the rear panel in a safe place to avoid damage; bending and scratching.
  • Page 454 6-16 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-2 System low voltage alarm Step Description If there is a low voltage alarm signal, restore the alarm cable to its original position and proceed to step 8. If there is no low voltage alarm signal, proceed to Procedure 6-3 to troubleshoot the alarm cable.
  • Page 455 Section 060-INDP-610 Maintenance Procedures Guide 6-17 Procedure 6-3 Enhanced alarm cable troubleshooting Step Description If multiple error indications are triggered, proceed to step 6. If multiple error indications are not triggered, return to the calling procedure and continue. Remove the defective enhanced alarm cable from the DMS-100 side. Follow the procedure in the associated IM for installing an enhanced alarm cable to replace the defective model.
  • Page 456 6-18 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-4 System high temperature alarm Step Description If the ambient temperature exceeds 100 o F, proceed to step 7. If the ambient temperature does not exceed 100 o F, proceed to step 3. Remove the enhanced alarm cable from the BMC at connector J16 of the A and B chassis.
  • Page 457 Replacement fuses for the Fan Filter PCA (NT6M56AD - 1/4 amp 8AG, part number 680-9176-001) and foam filters (part number 680-7859 or CPC A0379820) can be ordered from Nortel. Note: Fuse operation (a blown fuse) usually indicates a failure. Check the fan and associated cabling for shorts before replacing the fuse.
  • Page 458 6-20 Section 060-INDP-610 Maintenance Procedures Guide Replacing the fans Use Procedure 6-6 when replacing the cooling fans at the rear of the BMC chassis. Before replacement, make sure the following conditions are met: • The processor with the operational fan is in the ONLY mode of operation. •...
  • Page 459 Section 060-INDP-610 Maintenance Procedures Guide 6-21 Procedure 6-6 Cooling fan replacement Step Description Remove the rear panel of the chassis to be worked on. Figure 6-6 shows the eight screws to remove. Save the screws. Remove the two screws securing the fan mounting bracket in the chassis. These screws are on the outside of the chassis, in the upper left corner of the right hand panel, as seen from the rear.
  • Page 460 6-22 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 Removing BMC system rear panel and fan mounting screws Remove the two slotted-head screws to remove each fan. Remove the eight slotted-head screws to remove each cabinet back. 297-6201-502 Standard 01.02 September 2000...
  • Page 461 Section 060-INDP-610 Maintenance Procedures Guide 6-23 Replacing the Fan behind the Filler Panel Use Procedure 6-7 to replace the fan behind the Filler panel on the front of the lower processor chassis. Procedure 6-7 Filler panel fan replacement Step Description CAUTION Since all PCAs, disk drives, and other hardware in the BMC are static sensitive, be cautious.
  • Page 462 6-24 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-7 Filler panel fan replacement Step Description Remove the Fan Assembly. Look inside the space vacated by the Filler panel and locate the two screws securing the Fan Assembly. Remove the two fan mounting screws that hold the Fan Assembly in place. Save the screws for later use.
  • Page 463 Section 060-INDP-610 Maintenance Procedures Guide 6-25 56K Interface PCA Diagnostic Procedure The following procedure is used to diagnose problems with the 56K Interface PCA. Procedure 6-8 56K Interface PCA Diagnostic Step Description Note 3: This procedure assumes the user is logged into the BMC and that the BMC messages are directed to the local terminal.
  • Page 464 6-26 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-8 56K Interface PCA Diagnostic Step Description Enter the following commands to verify that the BOOTCP file contains the software load and version number of the program file on the disk. >CP BOOT LIST (cr) System response: filename vers where: filename- name of the CP boot file.
  • Page 465 Section 060-INDP-610 Maintenance Procedures Guide 6-27 Procedure 6-8 56K Interface PCA Diagnostic Step Description If an error was observed on the ERRMAP, reset the alarm using the following command: >RSERR 00 (cr) >DOS S RSERR 00 (cr) ALL ALARMS CLEARED message is issued and the status panel alarm lamp goes out. If the alarm returns, replace the 56K Interface PCA using the procedure in the Hardware Replacement subsection.
  • Page 466 6-28 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-8 56K Interface PCA Diagnostic Step Description CAUTION Loss of AMA can occur when the processors are switched during high traffic. Have the HOC perform a polling session to complete the verification of the 56K Interface PCA functionality.
  • Page 467 Section 060-INDP-610 Maintenance Procedures Guide 6-29 Procedure 6-9 Block Display Step Description Enter the following command to query the currently open AMA file. Note the starting sequence number for this version. >IDXMAINT DIR OPEN AMA (cr) If looking for AMA currently being written, go to step 6. Enter the following command to display the last block in the previous version: >IDXMAINT EXAMINE AMA PACKED seq_num (cr) where: seq_num - starting sequence number of version that was open minus 1.
  • Page 468 6-30 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-9 Block Display Step Description Enter the following command to close the open file: >IDXMAINT CREATE FILE AMA (cr) System response: AMA WRITE FILE CLOSED Enter the following command to display the sequence number: >IDXMAINT EXAMINE AMA PACKED seq_num (cr) If the BMC responds with a DATA NOT AVAILABLE message, proceed to step 2.
  • Page 469 Section 060-INDP-610 Maintenance Procedures Guide 6-31 Example of Displayed Block 96-05-21 13:04:08 TUE PROC-B OOOXXX AMA SEQ #61524 00 00 FO 54 F5 05 1A 00 05 20 11 42 00 00 00330000AA00020COOIC70120CO0000CO000000COCOCOCOOOC503C6641210CIC 00503C7724380C1140598CO00000119COCO11C00300000AAOOOOICO06C70120C .......0002266COCO11CBBBBBBBBBBBBBBBBBBB Table 6-3 Header Definitions Data Byte Definition 00 00 FO 54...
  • Page 470 6-32 Section 060-INDP-610 Maintenance Procedures Guide Table 6-4 Data Definitions Position Definition 00330000AA 4 bytes before AA are Record Descriptor Word (RDW) for following call record Start of new call record 5 characters after AA Structure code for call, refer to the Commands and Messages Guide section for breakdown of fields and definitions Field separator within call record 011CBBBBBB...
  • Page 471 Section 060-INDP-610 Maintenance Procedures Guide 6-33 If alarm appears on the standby processor, begin with step 2. If alarm is on the active processor, begin with step 1. If both processors respond with an ILLEGAL COMMAND message, begin with step 10. Procedure 6-10 Boot Recovery Step...
  • Page 472 6-34 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-10 Boot Recovery Step Description If program file name and version number from DOS LL command does not match the file name listed from LSTDIR ALL command, enter the following commands to recreate the boot file.
  • Page 473 Section 060-INDP-610 Maintenance Procedures Guide 6-35 Procedure 6-10 Boot Recovery Step Description If the processor does NOT boot the program file, replace the EPROM PCA using the procedure in the Hardware Replacement subsection and return to this point. If replacing the EPROM PCA does NOT allow the processor to boot the program file, replace the CPU PCA using the procedure in the Hardware Replacement subsection and return to this point.
  • Page 474 6-36 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-10 Boot Recovery Step Description Enter the following commands to verify whether there is a boot file and program file on disk at this time. >XDIR (cr)Responds with disk directory. >DOS LL (cr)Displays current boot file. Note: If response is BOOT FILE EMPTY, enter the DOS LA and DOS LL commands (step 3), then return to step 11.
  • Page 475 Section 060-INDP-610 Maintenance Procedures Guide 6-37 Procedure 6-10 Boot Recovery Step Description If the processor does NOT boot the program file, replace the EPROM PCA using the procedure in the Hardware Replacement subsection and return to this point. If replacing the EPROM PCA does NOT allow the processor to boot the program file, replace the CPU PCA using the procedure in the Hardware Replacement subsection and return to this point.
  • Page 476 6-38 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-10 Boot Recovery Step Description Note: BMC automatically attempts to load the program file three times. If the BMC loads successfully, proceed to step 20. Otherwise, perform the following steps. If the processor does NOT boot the program file, replace the EPROM PCA using the procedure in the Hardware Replacement subsection and return to this point.
  • Page 477 >DISK USAGE (cr) If the disk drive in error is supplied by Nortel, proceed to step 3. Otherwise proceed to step Verify that the PEC of the disk drive in error is NT6M72GA. If the PEC of the disk drive in error is not NT6M72GA, the disk drive must be replaced with the appropriate type.
  • Page 478 6-40 Section 060-INDP-610 Maintenance Procedures Guide Note 6: This procedure assumes that the disk subsystem worked at one time and no PCAs or disks have been replaced by previous troubleshooting activity. Note 7: Disk subsystem alarms often appear in groups and troubleshooting activity requires using all the presented information to correctly diagnose the problem.
  • Page 479 Section 060-INDP-610 Maintenance Procedures Guide 6-41 Procedure 6-12 Disk Drive Diagnostic Step Description If the DISK MODE ALARM is observed with the OFFLIN DSK FULL there may be AMA on the off-line disk that has not yet been polled. Refer to the Disk Full Procedure subsection for the procedure to recover from full disks before proceeding with this procedure The DSK CARD HW ERR points towards a problem with a SCSI Interface PCA.
  • Page 480 6-42 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-12 Disk Drive Diagnostic Step Description Put the other processor in the PRIME mode. The other processor is defined as that processor that does not have the suspected faulty pack. At the Switch and Status panel of the BMC: •...
  • Page 481 Section 060-INDP-610 Maintenance Procedures Guide 6-43 Procedure 6-12 Disk Drive Diagnostic Step Description Enter the following command to test the standby SCSI Interface PCA. >DPRTST (cr) System responds with the results of the test. If the test fails, replace the SCSI Interface PCA from the affected chassis using the procedure in the Hardware Replacement subsection.
  • Page 482 6-44 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-12 Disk Drive Diagnostic Step Description High disk usage when there is no polling problem indicates that files may exist outside the indices. Enter the following commands to determine the files contained in the AMAIDX and LOGIDX.
  • Page 483 Section 060-INDP-610 Maintenance Procedures Guide 6-45 Procedure 6-12 Disk Drive Diagnostic Step Description AMACRD, LOGCRD or other duplicate files found can be deleted. Repeat the following command for each file type that is to be deleted. If there is any question about the files found in either step 10 and 11, contact your next level of support before those files are deleted.
  • Page 484 6-46 Section 060-INDP-610 Maintenance Procedures Guide Disk Drive Full Procedure This procedure assumes the user has already determined that there is not a disk hardware failure using the procedure in the Disk Diagnostic Procedure subsection. Note 8: Verify data center is able to poll before starting this procedure. Note 9: Arrangements MUST be made with data center to poll while this procedure is in progress.
  • Page 485 Section 060-INDP-610 Maintenance Procedures Guide 6-47 Procedure 6-13 Disk Drive Full Step Description Enter the following command to verify that all data is polled: >IDXMAINT SUMMARY AMA (cr) Response should indicate 00000000 PRIMARY on the first line. If response does not indicate 00000000 PRIMARY, have data center poll again.
  • Page 486 6-48 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-13 Disk Drive Full Step Description Enter the following command to verify all data is polled: >IDXMAINT SUMMARY AMA (cr) If response indicates 00000000 PRIMARY on the first line, proceed to step 8. If response does not indicate 00000000 PRIMARY, have data center poll again.
  • Page 487 Section 060-INDP-610 Maintenance Procedures Guide 6-49 Procedure 6-13 Disk Drive Full Step Description Enter the following command to verify whether any AMACRD files are outside of the index. >LSTDIR FILE AMACRD 1 255 (cr) System responds with a directory listing of the AMACRD files on disk. Example:XX AMACRD XX 02 96 151 X XXXX XXXXXXX XX XXXXXX 020304 007500 1 FILES LISTED...
  • Page 488 6-50 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-13 Disk Drive Full Step Description Compare the printout in step 10 with a full directory listing to verify whether there are any files that need to be deleted. Enter the following (at the terminal): >LSTDIR ALL(cr) System responds with a directory listing of all files on this disk, by file name and version number.
  • Page 489 Section 060-INDP-610 Maintenance Procedures Guide 6-51 Disk Drive Recovery Procedure Procedure 6-14 Disk Drive Fault Determination Step Description Determine the current disk operation mode. Enter: (at the terminal) >DISK MODE (cr) System response: DISK MODE xx where: xx - current disk mode (AO, BO, AP, BP, or NONE) If the disk system mode shows either disk in the PRIME mode, there is no fault, procedure complete.
  • Page 490 Step Description CAUTION 1 Use the FORMAT command ONLY when in direct contact with Nortel field support personnel. This command may cause a loss of data. Perform the DISK FORMAT procedure during a period of low data gathering activity (low traffic) to avoid data losses.
  • Page 491 Section 060-INDP-610 Maintenance Procedures Guide 6-53 Procedure 6-16 Make disk system ONLY mode Step Description CAUTION This action may cause a loss of data. Verify your action with technical assistance personnel. Note: Refer to Table 6-6 for the allowed disk drive mode changes. Enter: (at the terminal) >DISK MODE xO (cr) where: x - disk drive (A or B)
  • Page 492 6-54 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-17 Make disk system PRIME mode Step Description Enter: (at the terminal) >DISK MODE xP (cr) where: x - disk drive (A or B) System response: DISK MODE: AP or DISK MODE: BP This procedure can take up to three hours.
  • Page 493 B ONLY Changes B disk to uninitialized. Not recommended. Note: This change is to be used for specific DISK FULL recovery procedures only. Contact Nortel if it becomes necessary to use this mode change. (Sheet 2 of 2) DRAM PCA Diagnostic Procedure This procedure is used to diagnose problems on the DRAM PCA.
  • Page 494 6-56 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-18 DRAM PCA (NT6M64AA) Diagnostic Step Description Enter the following commands to determine which shelf in the BMC has the alarm. >ERRMAP ALARMS (cr) System responds with a list of alarms on active and standby processors. >CLK (cr) System responds with a time stamp and the identity of the active processor.
  • Page 495 Section 060-INDP-610 Maintenance Procedures Guide 6-57 Procedure 6-18 DRAM PCA (NT6M64AA) Diagnostic Step Description The following command will perform a series of tests on the standby processor. >DOS S TEST (cr) System responds with a series of tests with results indicated as pass or fail. If the tests pass and the alarms stays clear, continue with step 4.
  • Page 496 6-58 Section 060-INDP-610 Maintenance Procedures Guide for the BMC are given. This procedure address the following types of index file corruption: • Version number missing from index, but is on disk. • Sequence numbers not incrementing properly. • AMAIDX OPEN ERROR:03. Version number missing from index, but is on disk Version numbers within the index are always supposed to be sequential and contiguous.
  • Page 497 Section 060-INDP-610 Maintenance Procedures Guide 6-59 Procedure 6-19 Version number Missing Recognition Step Description Display the closed AMACRD files in the index. >IDXMAINT DIR CLOSED AMA 200 (cr) Example response: VS 81: 3451 BLKS, 6 PRIMARY, AMA SEQ #00000000 VS 83: 36 BLKS, 36 PRIMARY, AMA SEQ #00003487 END OF AMAIDX FILE Display the open AMACRD file in the index.
  • Page 498 6-60 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-20 Version number Missing Recovery Step Description Identify the next sequence number of PRIMARY AMA in the index. For example: AMA FILE: 03 VSNS, 0003487 BLKS, 00000042 PRIMARY SEQ# 00000000 FIRST, 00003445 PRIM, 00003487 NEXT IN VS 81: 3451 BLKS, 6 PRIMARY, AMA SEQ #00000000 00003445 in the next sequence number of PRIMARY AMA.
  • Page 499 Section 060-INDP-610 Maintenance Procedures Guide 6-61 Procedure 6-20 Version number Missing Recovery Step Description Note that the number of PRIMARY blocks in the new index has changed from 42 to 78. This is an increase of 36 blocks. This is correct because the index file now correctly includes version 82 (which contains 36 blocks of PRIMARY AMA).
  • Page 500 6-62 Section 060-INDP-610 Maintenance Procedures Guide Incorrectly incrementing sequence numbers may be observed by displaying a listing of the closed AMACRD files in the index. The system should also report BAD AMAIDX FILE. Procedure 6-21 Sequence Number Not Incrementing Recognition Step Description Check the AMA Index File.
  • Page 501 Section 060-INDP-610 Maintenance Procedures Guide 6-63 109 (sequences 608740 through 608748). The actual AMA data in version 108, sequence numbers 608740 through 608748 will be different from the AMA data in version 109, sequence numbers 608740 through 608748, but the BMC will detect the duplicated sequence numbers and report, BAD AMAIDX FILE.
  • Page 502 6-64 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-22 Sequence Number Not Incrementing Recovery Step Description Display the closed AMACRD files in the index. Displaying the closed AMACRD files in the index shows that version 108 has been changed from PRIMARY to SECNDRY AMA. >IDXMAINT DIR CLOSED AMA 200 (cr) Example response: VS 106: 2968 BLKS, 99 DA SECNDRY, AMA SEQ #002747...
  • Page 503 Section 060-INDP-610 Maintenance Procedures Guide 6-65 Procedure 6-22 Sequence Number Not Incrementing Recovery Step Description Create a new AMAIDX file starting with the first good sequence number containing PRIMARY AMA. The following command creates a new AMA index, starting with version 109 as the first version having PRIMARY AMA data.
  • Page 504 6-66 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-22 Sequence Number Not Incrementing Recovery Step Description Delete the AMACRD files that were forced into SECNDRY status (versions 106-108): >DELFILE AMACRD 106 108 (cr) After the data center has confirmed the integrity of the AMA data collected during the demand poll, the AMACRD files in versions 106, 107 and 108 must be deleted.
  • Page 505 Section 060-INDP-610 Maintenance Procedures Guide 6-67 Procedure 6-23 AMAIDX Missing Recovery Step Description Examine available AMACRD files in the directory by typing: >LSTDIR FILE AMACRD 1 255 (cr) Note sequence number in the versions that are displayed. For example: 00 AMACRD 60 78 95 349 0 1531 01006C00 00 0EE509 063402 000076 78 is the file’s version number.
  • Page 506 6-68 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-23 AMAIDX Missing Recovery Step Description If any versions were left outside the index, these versions should remain on disk until data center can confirm the data will not need to be repolled. These versions MUST be deleted using the command in step 8.
  • Page 507 Section 060-INDP-610 Maintenance Procedures Guide 6-69 Procedure 6-24 No Block Last Hour Diagnostic Step Description Enter the following command to examine the alarms on the error map and the BMC current time. If there are any other alarms listed in the error map, troubleshoot those alarms prior to the NO BLOCK LAST PER alarm.
  • Page 508 6-70 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-24 No Block Last Hour Diagnostic Step Description Note the time that the alarm occurred. This can be done by viewing the alarm in one of the following ways: View the printout on the central office printer, if available, go to step 5. View the time the alarm was reported to the switch or alarm collection device, go to step 5.
  • Page 509 Section 060-INDP-610 Maintenance Procedures Guide 6-71 Procedure 6-24 No Block Last Hour Diagnostic Step Description Once the log messages have been viewed, the following command is issued to close the log file: >IDXMAINT CLOSE (cr) Response: READ FILE CLOSED Note: The time stamps in the logs reflect the BMC time. If the BMC time is wrong, the log times will also be wrong.
  • Page 510 6-72 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-24 No Block Last Hour Diagnostic Step Description Enter the following commands to clear any alarms in the BMC: >RSERR 00 (cr) and/or >DOS S RSERR 00 (cr) System responds with an ALL ALARMS CLEARED message and the status panel alarm lamp will go out.
  • Page 511 Section 060-INDP-610 Maintenance Procedures Guide 6-73 Polling Diagnostic Procedure This procedure assumes the user is logged into the BMC and that the BMC messages are directed to the local terminal. No output to a local terminal will occur if the user is not logged in or messages are directed to a DMS-10 printer.
  • Page 512 6-74 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-25 Polling Diagnostic Step Description Switch processors and see if the problem remains the same. If there are no alarms on the BMC, enter the following command to switch the processor: >SWACT (cr) System responds with messages indicating the processor switch.
  • Page 513 Section 060-INDP-610 Maintenance Procedures Guide 6-75 Procedure 6-25 Polling Diagnostic Step Description Go to step 14 to check the BMC and the modem clocks setting then continue with this step. Enter the following command to write this site dependent data to disk: >SITDAT WRITE (cr) System response: SITDAT FILE DISK JOB COMPLETE When polling fails from both shelves with no messages output to the local printer check...
  • Page 514 6-76 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-25 Polling Diagnostic Step Description If the Error map alarms includes the message INCOMING CALL REJECTED 01, there is a password problem. The host password was rejected by the BMC. Check password used by the poller and the value in the BMC site data through the command below. Note: After entering the following command, enter CTRL Z to exit the overlay.
  • Page 515 Section 060-INDP-610 Maintenance Procedures Guide 6-77 Procedure 6-25 Polling Diagnostic Step Description When an IMPROPER LINK DISCONNECT: RETRY LIMIT message is received, the polling problem could be caused by an incorrectly set modem line control value. Enter the following command to verify the current modem line control value: >CP CONTROL (cr) The system responds with the current modem line control value, either HD for Half Duplex (system default value) or FD for Full Duplex.
  • Page 516 6-78 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-25 Polling Diagnostic Step Description Other messages listed below are output as a result various failures. IMPROPER LINK DISCONNECT: RETRY LIMIT IMPROPER LINK DISCONNECT: TIMEOUT LINK TRANSMIT TIMEOUT LINK xx RETRY THRESH EXCEEDED< MSG: mm nn •...
  • Page 517 Download and Boot Software with Software Running The main software programs for the BMC are written on disk before the systems are shipped from Nortel. Periodic updates and patches to the software programs are issued and must be loaded onto disk as part of on-site activities.
  • Page 518 6-80 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-26 Download and Boot Software with Software Running Step Description Delete any unneeded files, if required. Enter (at the terminal): >DELFILE filename version (cr) Old program versions that are not expected to be run again are candidates for deletion. Save at least the three most current versions.
  • Page 519 Section 060-INDP-610 Maintenance Procedures Guide 6-81 Procedure 6-26 Download and Boot Software with Software Running Step Description Make a copy of all site dependent data on disk, as a first step in the installation of the "new" software. The old SITDAT file on disk may be incompatible with the new software. Refer to the System Administration Guide section for a list of all site dependent entries.
  • Page 520 6-82 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-26 Download and Boot Software with Software Running Step Description Make a copy of the present content of the TDYSTS file. Enter (at the terminal): >REPORT DISK TDAY (cr) >REPORT AMA TDAY (cr) >REPORT COM TDAY (cr) These commands print reports containing all of the statistical data items in the file about to be deleted.
  • Page 521 Section 060-INDP-610 Maintenance Procedures Guide 6-83 Procedure 6-26 Download and Boot Software with Software Running Step Description Remove the current software file names from the software boot file BOOTFL (identified by the DOS LL command) to allow insertion of the new software's file names (may need to repeat several times if more than one file is in the boot list).
  • Page 522 6-84 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-26 Download and Boot Software with Software Running Step Description Test if the software is functional. Try a few commands on the Standby Processor to verify the software. The command in this step displays the software and version IDs on the Standby Processor.
  • Page 523 Section 060-INDP-610 Maintenance Procedures Guide 6-85 Procedure 6-26 Download and Boot Software with Software Running Step Description Display all site specific data and match and compare to that data extracted in step 8. Verify that all editing has been completed correctly. If there are discrepancies, go back to step 25.
  • Page 524 6. CAUTION Do not perform step 6 if step 5 is successful; proceed to step 7. If it becomes necessary to perform step 6, contact Nortel immediately. (Sheet 1 of 5) 297-6201-502 Standard 01.02 September 2000...
  • Page 525 Section 060-INDP-610 Maintenance Procedures Guide 6-87 Procedure 6-27 Emergency Download and Boot Software with Software Not Running Step Description Format the A disk. Enter (at the terminal): >DISK FORMAT A (cr) Proper response: FORMAT DONE Make the disk mode A ONLY. Enter (at the terminal): >DISK MODE AO (cr) Repeat steps 4 and 5 for the B disk.
  • Page 526 6-88 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-27 Emergency Download and Boot Software with Software Not Running Step Description Monitor the terminal for the message: xxxxxx DOWNLOAD COMPLETE Message indicates that the download is complete. Installation of the "new" software is now required.
  • Page 527 Section 060-INDP-610 Maintenance Procedures Guide 6-89 Procedure 6-27 Emergency Download and Boot Software with Software Not Running Step Description Append a new software file name, as observed in step 14, into the boot file BOOTFL. Enter (at the terminal): >DOS LA (cr) prompt: FILE>...
  • Page 528 6-90 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-27 Emergency Download and Boot Software with Software Not Running Step Description "Boot-up" the new software on the Standby Processor. Enter (at the terminal): >DOS S DOS LB (cr) This completes the download and software boot procedure. Note: At this time, refer to the System Administration Guide section and enter the site data for the BMC system.
  • Page 529 Section 060-INDP-610 Maintenance Procedures Guide 6-91 Note: This procedure must not be performed at block input rates that exceed four blocks per minute. Procedure 6-28 Polling disks from a nonredundant mode Step Description Turn on the display of block headers as they are written to disk. This provides a visual indication of current AMA traffic.
  • Page 530 6-92 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-28 Polling disks from a nonredundant mode Step Description Enter (at the terminal): >LSTACT (cr) Alternate between steps 5 and 6 until the following response to the LSTACT command is seen: 0 FILES LISTED Note 6: If a block header is received at any time before moving on to step 7, repeat steps 3-6 until all active files are closed.
  • Page 531 Section 060-INDP-610 Maintenance Procedures Guide 6-93 Procedure 6-28 Polling disks from a nonredundant mode Step Description (Optional step) Enter the following command if you wish to keep track of the AMA files to be polled: >IDXMAINT DIR CLOSED AMA 200 (cr) Write any remaining call records to the AMA data file.
  • Page 532 6-94 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-28 Polling disks from a nonredundant mode Step Description Change the disk mode. Enter (at the terminal): >DISK MODE AO (cr) If the current disk mode is B ONLY. >DISK MODE BO (cr) If the current disk mode is A ONLY. CAUTION Do not change the disk mode to PRIME;...
  • Page 533 Section 060-INDP-610 Maintenance Procedures Guide 6-95 Procedure 6-28 Polling disks from a nonredundant mode Step Description Change from disk ONLY mode to disk PRIME mode. Perform this step before any new AMA data is received. The present disk has no new AMA data. The command sequence preserves any new AMA data that may remain on the other disk.
  • Page 534 6-96 Section 060-INDP-610 Maintenance Procedures Guide Quad SIO PCA Diagnostic Procedure This procedure assumes that the Quad SIO PCA worked at one time and has not been replaced or settings altered by previous troubleshooting activity. Refer to the switch settings portion of this manual for switch and jumper options if it is suspected that they have been changed.
  • Page 535 Section 060-INDP-610 Maintenance Procedures Guide 6-97 Procedure 6-29 Quad SIO PCA (NT6M60xx) Diagnostic Step Description Place the processor with the suspected faulty pack in the standby mode and repeat step 1. Put the other processor in the PRIME mode. The other processor is defined as that processor that does not have the suspected faulty pack.
  • Page 536: Secondary Data Polling

    6-98 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-29 Quad SIO PCA (NT6M60xx) Diagnostic Step Description Switch back to the processor where the alarm occurred and determine that communication to that shelf is ok. >CLK (cr) System responds with a time stamp and identity of the active processor. If response is normal, the procedure is complete.
  • Page 537 Section 060-INDP-610 Maintenance Procedures Guide 6-99 message to access secondary AMA data. This procedure is provided for information only. Procedure 6-30 Secondary Data Polling Step Description Modify the polling request message. Insert the SELGRP keyword, 29A (if not already present), into bytes 19-21 of the polling request message. The presence of this keyword indicates to the BMC that the value in byte 22 is the value that the SELGRP command will be set to in order to access a particular iteration of sequence numbers.
  • Page 538 6-100 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-30 Secondary Data Polling Step Description Contact the telephone company personnel and determine the reason for the unsuccessful polling session. If the SELGRP value that is used in the polling request message is invalid (greater than 6), the session is terminated and the following message is printed by the BMC: INVALID SELGRP: EMBEDDED COMMAND IGNORED...
  • Page 539: Site File Error

    Section 060-INDP-610 Maintenance Procedures Guide 6-101 Site File Error Procedure This procedure assumes the user is logged into the BMC and that the BMC messages are directed to the local terminal. No output to a local terminal will occur if the user is not logged in or messages are directed to a DMS-10 printer.
  • Page 540 6-102 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-31 Site File Error Step Description Enter the following command to verify the alarm by attempting to read the SITDAT file. >SITDAT READ (cr) System response: SITDAT FILE DISK JOB COMPLETE If the normal response above occurs, the SITDAT file is ok and the procedure is complete. If a SITDAT READ ERROR 03 message occurs, go to step 4.
  • Page 541 Section 060-INDP-610 Maintenance Procedures Guide 6-103 Procedure 6-31 Site File Error Step Description With no site data file on the disk, a SITDAT file must be created. Enter the following command to create the SITDAT file: >SITDAT WRITE (cr) System response: SITDAT FILE DISK JOB COMPLETE If the response above occurs, go to step 7.
  • Page 542 6-104 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-31 Site File Error Step Description The site data in memory may be corrupt. Obtain the BMC site data. Delete any site data files from the BMC disks with the following command: >DELFILE SITDAT 1 255 (cr) System response: x FILE DELETED where: x - version number of file deleted.
  • Page 543 Section 060-INDP-610 Maintenance Procedures Guide 6-105 Table 6-7 Site Data Commands Commands Site Dependent Information AMAHRS BAUD BUFSZ BVALID CP CLOCK CP CONTROL CP INTERFACE ERRMAP KYWD LPAD PSWD SETTERM SITDAT READ SITDAT WRITE VALPARM BLOCKS VALPARM INVALID DMSO ***DMS-10*** (Sheet 1 of 2) BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 544 6-106 Section 060-INDP-610 Maintenance Procedures Guide Table 6-7 Site Data Commands Commands Site Dependent Information DMSP ***DMS-10*** DMST ***DMS-10**** (Sheet 2 of 2) 297-6201-502 Standard 01.02 September 2000...
  • Page 545: Statistical File Error

    Section 060-INDP-610 Maintenance Procedures Guide 6-107 Statistical File Error Procedure This procedure assumes the user is logged into the BMC and that the BMC messages are directed to the local terminal. No output to a local terminal will occur if the user is not logged in or messages are directed to a DMS-10 printer.
  • Page 546 6-108 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-32 Statistical File Error Step Description The STAT FILE ERROR error map alarm message can occur if the statistics files are damaged or multiple files are present on the disk. Enter the following commands to determine the number of each type of statistics files on the disk.
  • Page 547: System Reboot

    Section 060-INDP-610 Maintenance Procedures Guide 6-109 Procedure 6-32 Statistical File Error Step Description Enter the following commands to delete all the statistics files from the disk and create a new open TDYSTS file: >DELFILE nnnnnn 1 255 (cr) where: nnnnnn - TDYSTS and/or YDYSTS System response: x FILES DELETED where: x - number of files deleted.
  • Page 548 6-110 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-33 System Reboot Step Description Enter the following command to verify which processor is currently active. >CLK (cr) System response: yy-mm-dd hh:mm:ss DAY PROC-x where: x - A or B indicating processor ID. Make sure the processor that produced the error message is standby.
  • Page 549 Section 060-INDP-610 Maintenance Procedures Guide 6-111 Procedure 6-33 System Reboot Step Description If the processor does NOT start to boot the program file, replace the EPROM PCA (NT6M63xx) using the procedure in the Hardware Replacement subsection and return to this point. If replacing the EPROM PCA does NOT allow the processor to start to boot the program file, replace the CPU PCA using the procedure in the Hardware Replacement subsection and return to this point.
  • Page 550 6-112 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-33 System Reboot Step Description Switch to the newly loaded processor by depressing the A/B rocker switch toward A or B, to match the newly loaded processor and turn the key switch. If there are no processor switch messages, enter the following command to verify alarm condition and troubleshoot any alarms that are observed: >ERRMAP ALARMS (cr)
  • Page 551 Section 060-INDP-610 Maintenance Procedures Guide 6-113 Procedure 6-34 TEC/DSI PCA Diagnostic Step Description Enter the following command to switch processors: >SWACT (cr) BMC will respond with appropriate switch related messages. If the processors do not switch, depress the A/B rocker switch to match the standby processor. Depress the O/P rocker switch to O.
  • Page 552 6-114 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-34 TEC/DSI PCA Diagnostic Step Description You should observe that the LED display on the CPU PCA is a lower case 'r.'. When this display changes to any other character, there should be some steady activity on the disk drive LED followed by a terminal message, STBY BOOT IN PROC.
  • Page 553 Section 060-INDP-610 Maintenance Procedures Guide 6-115 Procedure 6-34 TEC/DSI PCA Diagnostic Step Description Verify AMA/MTU port function in the Switching System. • Are they both up? • Which port is active? • Can block count increase be seen at TEC/DSI PCA when TECMAINT SHOW 1 or 2 STATUS is queried? •...
  • Page 554 6-116 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-34 TEC/DSI PCA Diagnostic Step Description • Pull ribbon cables attached to slots 12 and 13. • Remove the TEC/DSI PCA from slot 13. • Set jumper and switch settings for the slot 12 position. •...
  • Page 555 Section 060-INDP-610 Maintenance Procedures Guide 6-117 MTU Bx: CMD-yy STA-zz BLK-nnnn where: x- 0 or 2 (0 = TEC/DSI PCA in slot 13, 2 = TEC/DSI PCA in slot 12). yy- last command seen from Switching System (in hex). zz- current status (in hex). nnnn- block count when status was reported/requested.
  • Page 556 6-118 Section 060-INDP-610 Maintenance Procedures Guide Hardware Replacement This section contains the procedures to replace the various hardware elements of the BMC system. Powering Down BMC System for Maintenance Powering down the BMC system for performing maintenance on the various subassemblies is divided into two categories: •...
  • Page 557 Section 060-INDP-610 Maintenance Procedures Guide 6-119 rocker switch, ON, to restore the +8.5 V dc line. The disk drive in this chassis is not affected by removal of the +8.5 V dc source. PCA Replacement Procedures The following subsections contain the procedures necessary to replace various BMC PCAs.
  • Page 558 6-120 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-35 Miscellaneous PCA replacement Step Description Get the replacement PCA from the spares kit. Remove the protective electrostatic bag and place it on a suitable, grounded surface. Make sure the replacement PCA matches the faulty PCA’s part number and has the correct revision level.
  • Page 559: Miscellaneous Pca Replacement

    Section 060-INDP-610 Maintenance Procedures Guide 6-121 Procedure 6-35 Miscellaneous PCA replacement Step Description The replacement PCA option settings must be set to match the PCA being removed, if present, prior to installation. The default option settings for each PCA are described in the tables and figures listed below: PCARelated tableRelated figure CPUTable 6-9Figure 6-7...
  • Page 560 6-122 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-35 Miscellaneous PCA replacement Step Description To place the active processor unit in PRIME mode, perform the following steps at the Switch and Status Panel of the BMC: a. Press the A/B Select Switch to match the active processor. b.
  • Page 561 Section 060-INDP-610 Maintenance Procedures Guide 6-123 Table 6-9 CPU with DMA PCA (A1 and B1) options - part number: NT6M62BA Device type Position/setting Function Setting number Factory On-site Note: There are no customer-definable options on this PCA. Information is shown for reference only.
  • Page 562 6-124 Section 060-INDP-610 Maintenance Procedures Guide Table 6-9 CPU with DMA PCA (A1 and B1) options - part number: NT6M62BA Device type Position/setting Function Setting number Factory On-site DIP Switch Display Mode34 (SW2-3) (SW2-4) Err Cont PortOnOff Monitors Error Control. 3 = On 4 = Off I/O 6 PortOffOn...
  • Page 563 Section 060-INDP-610 Maintenance Procedures Guide 6-125 Figure 3-1 CPU with DMA PCA (A1 and B1) options (NT6M62BA) LED Display ♦ Note: Switch SW2 is a four-position right angle dip switch at the edge of the CPU circuit pack. BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 564 6-126 Section 060-INDP-610 Maintenance Procedures Guide Table 6-10 EPROM PCA (A2 and B2) options - part numbers: NT6M63FI and NT6M63FL Device Setting Function IC Configuration (number) Factory On-site Jumper Indicates presence of (P2) DRAM PCA. Jumper Configuration set-up for IC Type Jumpers Devices (P3)
  • Page 565 Section 060-INDP-610 Maintenance Procedures Guide 6-127 Table 6-10 EPROM PCA (A2 and B2) options - part numbers: NT6M63FI and NT6M63FL Device Setting Function IC Configuration (number) Factory On-site Jumper Memory paging is (P24) enabled. Strap None Used None Used Switch Rotary None Used Switch...
  • Page 566 6-128 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 EPROM PCA (A2 and B2) options (NT6M63FI and NT6M63FL) P3 P4 EPROM PCA NT6M63 REL. 297-6201-502 Standard 01.02 September 2000...
  • Page 567 Section 060-INDP-610 Maintenance Procedures Guide 6-129 Table 6-11 DRAM Expansion PCA (A3 and B3) options - part number: NT6M64AA Device type Position/ Function Setting (number) setting Factory On-site Jumper A Must be the Card 1 same as the Card 2 (card 1 in A3) factory setting.
  • Page 568 6-130 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 DRAM Expansion PCA (A3 and B3) options (NT6M64AA) • • • 297-6201-502 Standard 01.02 September 2000...
  • Page 569 Section 060-INDP-610 Maintenance Procedures Guide 6-131 Table 6-12 Quad SIO PCA (A6 and B6) options - part number: NT6M60BA Device Position/setting Function Setting type Factory On-site Note 5: This PCA supports polling on digital data lines or on analog network. For digital data lines check that: a.
  • Page 570 6-132 Section 060-INDP-610 Maintenance Procedures Guide Table 6-12 Quad SIO PCA (A6 and B6) options - part number: NT6M60BA Device Position/setting Function Setting type Factory On-site Jumper Channel D Rx external Channel D receive (J9) Channel D Rx internal clock Jumper Select external timing source Select internal or...
  • Page 571 Section 060-INDP-610 Maintenance Procedures Guide 6-133 Table 6-12 Quad SIO PCA (A6 and B6) options - part number: NT6M60BA Device Position/setting Function Setting type Factory On-site Switch Asynch Synch Switch Asynch Synch position rate rate position rate rate 1800 1200 2000 1760 2400...
  • Page 572 6-134 Section 060-INDP-610 Maintenance Procedures Guide Table 6-12 Quad SIO PCA (A6 and B6) options - part number: NT6M60BA Device Position/setting Function Setting type Factory On-site Rotary 1800 DMS-100 DMS-100 Switch 2000 MTC PTR. LNK 2 (S4) 2400 Async channel (1200) 134.5 3600...
  • Page 573 Section 060-INDP-610 Maintenance Procedures Guide 6-135 Figure 3-1 Quad SIO PCA (A6 and B6) options (NT6M60BA) J5 J4 BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 574 6-136 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 Quad SIO PCA (NT6M60BA) baud rate selector switches Quad SIO printed circuit assembly in slots A6 and B6 Baud 4 (S5) DMS-100 - MTC PTR 1 DMS-10 - MTC PTR 1 Baud 3 (S4) DMS-100 - MTC PTR 2 DMS-10 - SDI Port Baud 2 (S3)
  • Page 575 Section 060-INDP-610 Maintenance Procedures Guide 6-137 Figure 3-1 Quad SIO PCA (NT6M60BA) peripheral switches and indicators Quad SIO Card Transfer Select Switch Channel 4 Channel 3 Channel 2 Channel 1 Channel 4 LED Channel 3 LED Channel 2 LED Channel 1 LED SWITCH S6 CHANNEL POSITIONS POSITION FUNCTION...
  • Page 576 6-138 Section 060-INDP-610 Maintenance Procedures Guide Table 6-13 SCSI Interface PCA (A11 and B11) options - part number: NT6M66CA Device type Position/setting Function Setting (number) Factory On-site Jumper Out - Watchdog disable Watchdog timer In - Watchdog enable control Jumper Out - NMI disable NMI control In - NMI enable...
  • Page 577 Section 060-INDP-610 Maintenance Procedures Guide 6-139 Figure 3-1 SCSI Interface PCA (NT6M66CA) options - slot 11 BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 578 6-140 Section 060-INDP-610 Maintenance Procedures Guide Table 6-14 DSI PCAs (slots 12 and 13) options - part number: NT6M70BD - DMS-100 only Position/setting Function Setting Device Factory On-site type (number) Strap x = strap to center post U42 and U41Chip type;...
  • Page 579 Section 060-INDP-610 Maintenance Procedures Guide 6-141 Table 6-14 DSI PCAs (slots 12 and 13) options - part number: NT6M70BD - DMS-100 only Position/setting Function Setting Device Factory On-site type (number) DIP Switch (X = On, Y = Off) Must be Slot 12 (S1) 12345678 Select:...
  • Page 580 6-142 Section 060-INDP-610 Maintenance Procedures Guide Table 6-14 DSI PCAs (slots 12 and 13) options - part number: NT6M70BD - DMS-100 only Position/setting Function Setting Device Factory On-site type (number) Switch None used Note: There are no customer-definable options on this PCA. Information is for reference only. Use this data for verification during initial BMC system installation and/or PCA replacement to make sure the replacement PCA is set up the same as the PCA being replaced.
  • Page 581 Section 060-INDP-610 Maintenance Procedures Guide 6-143 Figure 3-1 DSI PCA (A12, B12, A13, and B13) options (NT6M70BD - DMS-100) BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 582 6-144 Section 060-INDP-610 Maintenance Procedures Guide Table 6-15 TEC PCAs (slots 12 and 13) options - part number: NT6M89BD - DMS-10 only Position/setting Function Setting Device Factory On-site type (number) Strap x = strap to center post U11, U12 & U48 Chip type;...
  • Page 583 Section 060-INDP-610 Maintenance Procedures Guide 6-145 Table 6-15 TEC PCAs (slots 12 and 13) options - part number: NT6M89BD - DMS-10 only Position/setting Function Setting Device Factory On-site type (number) DIP Switch (X = On, Y = Off) Must be Slot 12 (S1) 12345678 Select:...
  • Page 584 6-146 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 TEC PCA (A12, B12, A13, and B13) options (NT6M89BD - DMS-10 only) 297-6201-502 Standard 01.02 September 2000...
  • Page 585 Section 060-INDP-610 Maintenance Procedures Guide 6-147 Replacing EPROM integrated circuits The BMC contains EPROM firmware routines. EPROM ICs contain operational programming for some BMC system functions. The EPROM’s fixed memory is factory programmed with necessary control instructions. After installation in the BMC, the EPROM always responds in the same manner.
  • Page 586: Eprom Ic Installation Procedure

    Do not throw the EPROM away; return it to Nortel. Remove the new EPROM IC from its packing material and place it on a smooth flat surface so the pins are facing down and the coded identification label can be read from the top.
  • Page 587 Section 060-INDP-610 Maintenance Procedures Guide 6-149 Error Control II PCA Replacement (NT6M65AA) When replacing the Error Control II PCA in slot A5 (A chassis), use the following procedure. Refer to Table 6-16 and Figure 6-16 for a description of the switch and jumper options for this PCA. Procedure 6-37 Error Control II PCA replacement (NT6M65AG) Step...
  • Page 588 6-150 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-37 Error Control II PCA replacement (NT6M65AG) Step Description Note: This will create an alarm. ONLY MODE NON-REDUNDANT Enter the following commands to write the value 00 in the DRAM memory address 2204 for the off-line TEC/DSI PCAs: >DOS S TECMAINT MEMWRITE 1 2204 00 (cr) >DOS S TECMAINT MEMWRITE 2 2204 00 (cr)
  • Page 589 Section 060-INDP-610 Maintenance Procedures Guide 6-151 Procedure 6-37 Error Control II PCA replacement (NT6M65AG) Step Description To clear any alarms on the standby processor, enter at the maintenance terminal: >DOS S RSERR 00 (cr) Alarms will stay clear on the standby processor if there are no faults. To clear any alarms on the active processor, enter at the maintenance terminal: >RSERR 00 (cr) Alarms will clear if there are no faults.
  • Page 590 6-152 Section 060-INDP-610 Maintenance Procedures Guide Table 6-16 Error Control II PCA options - part number: NT6M65AG Device type Position/setting Function Setting (number) Factory On-site Jumper None Used Strap None Used DIP Switch None Used Rotary Switch None Used Switch None Used Note: There are no customer-definable options on this PCA.
  • Page 591 Section 060-INDP-610 Maintenance Procedures Guide 6-153 Figure 3-1 Error Control II PCA options (NT6M65AG) BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 592: Error Control Ii Jumper Pca Replacement (Ntm609Ab)

    6-154 Section 060-INDP-610 Maintenance Procedures Guide Error Control II Jumper PCA Replacement (NTM609AB) When replacing the Error Control II Jumper PCA, use the following procedure. Refer to Table 6-17 and Figure 6-17 for a description of the switch and jumper options for this PCA. 297-6201-502 Standard 01.02 September 2000...
  • Page 593 Section 060-INDP-610 Maintenance Procedures Guide 6-155 Procedure 6-38 Error Control II Jumper PCA replacement (NTM609AB) Step Description CAUTION Since all BMC PCAs are static sensitive, be careful when handling them. Wear a wrist grounding strap when working with the BMC. WARNING Since the BMC is powered up during this procedure, observe all safety procedures for operations on live equipment.
  • Page 594 6-156 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-38 Error Control II Jumper PCA replacement (NTM609AB) Step Description Enter the following commands to write the value 00 in the DRAM memory address 2204 for the off-line TEC/DSI PCAs: >DOS S TECMAINT MEMWRITE 1 2204 00 (cr) >DOS S TECMAINT MEMWRITE 2 2204 00 (cr) Remove power from the standby chassis (B processor) by operation of the +8 V dc red rocker switch on the power supply.
  • Page 595 Section 060-INDP-610 Maintenance Procedures Guide 6-157 Procedure 6-38 Error Control II Jumper PCA replacement (NTM609AB) Step Description To clear any alarms on the active processor, enter at the maintenance terminal: >RSERR 00 (cr) Alarms will clear if there are no faults. When all maintenance activities are complete, be sure to replace the front panel of the BMC.
  • Page 596 6-158 Section 060-INDP-610 Maintenance Procedures Guide Table 6-17 Error Control II Jumper PCA options - part number: NTM609AB Device type Position/setting Function Setting (number) Factory On-site Jumper None Used Strap None Used DIP Switch None Used Rotary Switch None Used Switch On = up position = power cut to...
  • Page 597 Section 060-INDP-610 Maintenance Procedures Guide 6-159 Figure 3-1 Error Control II Jumper PCA options (NTM609AB) Note: LED (DS1) lights when toggle switch (SW1) is moved to the (up) On position. BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 598 6-160 Section 060-INDP-610 Maintenance Procedures Guide 56K Interface PCA Replacement (NT6M94AA) To replace the 56K Interface PCA, use the following procedure. Refer to Table 6-18 and Figure 6-18 for a description of the switch and jumper options for this PCA. Procedure 6-39 56K Interface PCA replacement (NT6M94AA) Step...
  • Page 599 Section 060-INDP-610 Maintenance Procedures Guide 6-161 Procedure 6-39 56K Interface PCA replacement (NT6M94AA) Step Description Note: This will create an alarm: ONLY MODE NON-REDUNDANT Enter the following commands to write the value 00 in the DRAM memory address 2204 for the off-line TEC/DSI PCAs: >DOS S TECMAINT MEMWRITE 1 2204 00 (cr) >DOS S TECMAINT MEMWRITE 2 2204 00 (cr) Remove power from the standby chassis (A or B;...
  • Page 600 6-162 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-39 56K Interface PCA replacement (NT6M94AA) Step Description After RSERR, alarms may reappear. The command, CP TEST, forces diagnostics that confirm whether the faults were corrected. Enter (at the terminal): >CP TEST STDBY (cr) Place the active processor unit in PRIME mode.
  • Page 601 Section 060-INDP-610 Maintenance Procedures Guide 6-163 Procedure 6-39 56K Interface PCA replacement (NT6M94AA) Step Description Test the Active processor. Enter (at the terminal): >TEST (cr) >CP TEST ACT (cr) >DOS S TEST (cr) >CP TEST STDBY (cr) Note: The tests will take several minutes to execute, and the program test is the last test to run. Verify that the replacement PCA has corrected the original error.
  • Page 602 6-164 Section 060-INDP-610 Maintenance Procedures Guide Table 6-18 56K Interface PCA (A7 and B7) options - part number: NT6M94AA Device type Position/setting Function Setting (number) Factory On-site Jumper Out=select card 1 Card 1 or 2 address (P2) In=select card 2 selection Jumper Out=256K (27C256)
  • Page 603 Section 060-INDP-610 Maintenance Procedures Guide 6-165 Figure 3-1 56K Interface PCA options (NT6M94AA) BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 604: Scsi Crossover Pca Replacement (Nt6M93Ba)

    6-166 Section 060-INDP-610 Maintenance Procedures Guide SCSI Crossover PCA Replacement (NT6M93BA) To replace the SCSI Crossover PCA, use the following procedure. Refer Table 6-19 and Figure 6-19 for a description of the switch and jumper options for this PCA. Procedure 6-40 SCSI Crossover PCA replacement (NT6M93BA) Step Description...
  • Page 605 Section 060-INDP-610 Maintenance Procedures Guide 6-167 Procedure 6-40 SCSI Crossover PCA replacement (NT6M93BA) Step Description Loosen the slotted screws which fasten the outer edges of the appropriate rear panel assembly to the cabinet. Pull the rear panel away from the cabinet. Remove the front panel of the chassis to improve cooling, if necessary.
  • Page 606 6-168 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-40 SCSI Crossover PCA replacement (NT6M93BA) Step Description Note: Verify the cable markings (identification) or attach labels to the cables for correct positioning. WARNING Incorrect positioning of jumper may cause loss of AMA. Verify the repair by switching disk modes back to PRIME.
  • Page 607 Section 060-INDP-610 Maintenance Procedures Guide 6-169 Procedure 6-40 SCSI Crossover PCA replacement (NT6M93BA) Step Description Clear any alarms on the BMC. At the maintenance terminal, enter: >RSERR 00 (cr) >DOS S RSERR 00 (cr) Alarms will stay clear on the BMC if there are no faults. Place the active processor unit in PRIME mode.
  • Page 608 6-170 Section 060-INDP-610 Maintenance Procedures Guide Table 6-19 SCSI Crossover PCA options - part number: NT6M93BA Device type Position/setting Function Setting (number) Factory On-site Jumper 1-2disk A Disk A select A/B (refer (J5) 2-3disk B Disk B select to notes 2 and 3) Strap None Used...
  • Page 609 Section 060-INDP-610 Maintenance Procedures Guide 6-171 Figure 3-1 SCSI Crossover PCA options (NT6M93BA) BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 610: Power And Alarm Communications Pca Replacement (Nt6M84Ba)

    6-172 Section 060-INDP-610 Maintenance Procedures Guide Power and Alarm Communications PCA replacement (NT6M84BA) To replace the P/A Comm PCA, use the following procedure. Refer to Table 6-20 and Figure 6-20 for a description of the switch and jumper options for this PCA.
  • Page 611 Section 060-INDP-610 Maintenance Procedures Guide 6-173 Procedure 6-41 Power and Alarm Communications PCA replacement (NT6M84BA) Step Description Make sure any PCA option settings are set the same as the ones on the PCA being replaced. Note: Improper performance can be caused by incorrect settings, and produce fault-like symptoms in the BMC.
  • Page 612 6-174 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-41 Power and Alarm Communications PCA replacement (NT6M84BA) Step Description If BMC status panel shows processor is in ONL mode go to step 13, otherwise go to step Place the active processor unit in PRIME mode. At the Switch and Status Panel of the BMC: a.
  • Page 613 Section 060-INDP-610 Maintenance Procedures Guide 6-175 Table 6-20 Power and Alarm Communications PCA options (NT6M84BA) Device Position/Setting Function Setting Type Factory On-Site Num. Note 6: There are no customer-definable options on this PCA. Information is shown for reference only. This data is to be used for verification during initial BMC system installation and/or PCA replacement to make sure the replacement PCA is set-up the same as the PCA being replaced.
  • Page 614 6-176 Section 060-INDP-610 Maintenance Procedures Guide Table 6-20 Power and Alarm Communications PCA options (NT6M84BA) Device Position/Setting Function Setting Type Factory On-Site Num. Jumper 1-2 Rover terminal jack Rover terminal select Must be enabled control same as factory 2-3 Rover terminal jack setting disabled Jumper...
  • Page 615 Section 060-INDP-610 Maintenance Procedures Guide 6-177 Table 6-20 Power and Alarm Communications PCA options (NT6M84BA) Device Position/Setting Function Setting Type Factory On-Site Num. DIP Switch Chan.Int/S1-S2 External clock is derived by Must be No.ExtSetting looping around the TCIn same as signals.
  • Page 616 6-178 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 Power and alarm communications PCA options (NT6M84BA) • 297-6201-502 Standard 01.02 September 2000...
  • Page 617 Section 060-INDP-610 Maintenance Procedures Guide 6-179 56K Crossover PCA replacement (NT6M48AA) To replace the 56K Crossover PCA, use the following procedure. Refer to Table 6-21 and Figure 6-21 for a description of the switch and jumper options for this PCA. Procedure 6-42 56K Crossover PCA replacement (NT6M48AA) Step...
  • Page 618 6-180 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-42 56K Crossover PCA replacement (NT6M48AA) Step Description Note: When replacing the screws, align carefully before tightening to avoid stripping. Tighten the screws, alternating until all are equally tight. Do not “cinch down” any one screw until all are properly aligned;...
  • Page 619 Section 060-INDP-610 Maintenance Procedures Guide 6-181 Procedure 6-42 56K Crossover PCA replacement (NT6M48AA) Step Description Reattach any cables removed in step 4 in reverse order. Note: Verify the cable markings (identification) or attach labels to the cables for correct positioning. WARNING Incorrect positioning of cables will cause alarms and polling problems.
  • Page 620 6-182 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-42 56K Crossover PCA replacement (NT6M48AA) Step Description Display all active alarms. Enter: (at the terminal) >ERRMAP ALARMS (cr) If active alarms are present, troubleshoot using the related message table(s) in the Command and Message Guide section and/or contact the next level of support. Verify replacement PCA has corrected original error.
  • Page 621 Section 060-INDP-610 Maintenance Procedures Guide 6-183 Table 6-21 56K Crossover PCA (B16) options - part number: NT6M48AA Device type Position/setting Function Setting (number) Factory On-site Switch None Used Note: There are no customer-definable options on this PCA. Information is shown for reference only.
  • Page 622 6-184 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 56K Crossover PCA options (NT6M48AA) ♦ ♦ ♦ ♦ ♦ ♦ NT6M48_ _ REL 56K XOVR ♦ ♦ ♦ Power Connector ♦ ♦ ♦ ♦ 297-6201-502 Standard 01.02 September 2000...
  • Page 623: Connector Pca Replacement (Nt6M49Aa)

    Section 060-INDP-610 Maintenance Procedures Guide 6-185 56K Connector PCA Replacement (NT6M49AA) To replace the 56K Connector PCA, use the following procedure. Refer to Table 6-22 and Figure 6-22 for a description of the switch and jumper options for this PCA. Procedure 6-43 56K Connector PCA replacement (NT6M49AA) Step...
  • Page 624 6-186 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-43 56K Connector PCA replacement (NT6M49AA) Step Description Note: Be sure to hold the attached nuts and washers as you remove the standoffs. Do not allow the nuts and washers to fall into the chassis. Gently remove the 56K Connector PCA from its position.
  • Page 625 Section 060-INDP-610 Maintenance Procedures Guide 6-187 Table 6-22 56K Connector PCA (B26) options - part number: NT6M49AA Device type Position/setting Function Setting (number) Factory On-site Switch None Used BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 626 6-188 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 56K Connector PCA options (NT6M49AA) 297-6201-502 Standard 01.02 September 2000...
  • Page 627 Section 060-INDP-610 Maintenance Procedures Guide 6-189 Bus Terminator PCA Replacement (NT6M68AA) See the following procedures for replacing this PCA. Refer to Table 6-23 and Figure 6-23 for a description of the switch and jumper options on this PCA. Procedure 6-44 Bus Terminator PCA replacement (NT6M68AA) - version numbers G12 or earlier (e.g., D09 or E12) Step...
  • Page 628 6-190 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-44 Bus Terminator PCA replacement (NT6M68AA) - version numbers G12 or earlier (e.g., D09 or E12) Step Description Place the processor unit with the suspected faulty pack in the standby mode, by putting the other processor in the ONLY mode.
  • Page 629 Section 060-INDP-610 Maintenance Procedures Guide 6-191 Procedure 6-44 Bus Terminator PCA replacement (NT6M68AA) - version numbers G12 or earlier (e.g., D09 or E12) Step Description Fold the TEC/DSI cables back into position along the outer wall of the chassis. Remount the ribbon cable shield over the TEC/DSI cables. If the shield does not fit properly, check the folding of the TEC/DSI cables.
  • Page 630 6-192 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-44 Bus Terminator PCA replacement (NT6M68AA) - version numbers G12 or earlier (e.g., D09 or E12) Step Description Enter the following command at the maintenance terminal to Switch Processors to make the standby active: >SWACT (cr) The old standby is now the active processor.
  • Page 631: Bus Terminator Pca Replacement (Nt6M68Aa) - Version Numbers H01 Or Later

    Section 060-INDP-610 Maintenance Procedures Guide 6-193 Procedure 6-45 Bus Terminator PCA replacement (NT6M68AA) - version numbers H01 or later Step Description CAUTION Since all BMC PCAs are static sensitive, be careful when handling them. Wear a wrist grounding strap when working with the BMC. WARNING Since the BMC is powered up during this procedure, observe all safety procedures for operations on live equipment.
  • Page 632 6-194 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-45 Bus Terminator PCA replacement (NT6M68AA) - version numbers H01 or later Step Description Place the processor unit with the suspected faulty pack in the standby mode, by putting the other processor in the ONLY mode. The other processor is defined as that processor that does not have the suspected faulty pack.
  • Page 633 Section 060-INDP-610 Maintenance Procedures Guide 6-195 Procedure 6-45 Bus Terminator PCA replacement (NT6M68AA) - version numbers H01 or later Step Description Hold the cables out of the way. Remove the suspected faulty Bus Terminator PCA (using firm, even pressure) by inserting a finger in the hole in the PCA. Insert the replacement Bus Terminator PCA.
  • Page 634 6-196 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-45 Bus Terminator PCA replacement (NT6M68AA) - version numbers H01 or later Step Description To place the active processor unit in PRIME mode, perform the following steps at the Switch and Status Panel of the BMC: a.
  • Page 635 Section 060-INDP-610 Maintenance Procedures Guide 6-197 Table 6-23 Bus Terminator PCA options - part number: NT6M68AA Device type Position/setting Function Setting (number) Factory On-site Strap None used DIP Switch None used Rotary Switch None used Switch None used Jumper None used Note: There are no customer-definable options on this PCAs.
  • Page 636: Four-Channel Communication Pca Replacement (Nt6M85Aa)

    6-198 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 Bus Terminator PCA options (NT6M68AA) Four-Channel Communication PCA replacement (NT6M85AA) To replace the Four-Channel Communication PCA, use the following procedure. Refer to Table 6-24 and Figure 6-24 for a description of the switch and jumper options on this PCA.
  • Page 637 Section 060-INDP-610 Maintenance Procedures Guide 6-199 Procedure 6-46 Four-Channel Communication PCA replacement (NT6M85AA) Step Description Make sure no polling is occurring. Perform this procedure during a maintenance window. Notify technical assistance personnel of the temporary loss of MMI. Remove the slotted screws that fasten the outer edges of the A rear panel assembly to the cabinet.
  • Page 638 6-200 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-46 Four-Channel Communication PCA replacement (NT6M85AA) Step Description Seat the rear panel in its fully seated position and reinstall the slotted pan head screws previously removed. Verify that the MMI functions are operating properly. The procedure is complete.
  • Page 639 Section 060-INDP-610 Maintenance Procedures Guide 6-201 Table 6-24 Four-Channel Communications PCA (A17) options - part number: NT6M85AA Device type Position/setting Function Setting (number) Factory On-site Switch None Used BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 640 6-202 Section 060-INDP-610 Maintenance Procedures Guide Figure 3-1 Four-Channel Communications (A17) PCA (NT6M85AA) options Notes: 1. When used with digital data lines, make sure this pack is release 03 or later. 2. Jumpers J6, J7, J8, J9, and J10 may be on the reverse side of some PCAs. 297-6201-502 Standard 01.02 September 2000...
  • Page 641 Section 060-INDP-610 Maintenance Procedures Guide 6-203 Power Supply Replacement (NT6M71AB) If maintenance requires the removal of a power supply, using the following procedure. The only tool needed is a small flat-blade screwdriver. If necessary, have replacement fuses on hand. Procedure 6-47 Power supply (NT6M71AB) replacement Step Description...
  • Page 642 6-204 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-47 Power supply (NT6M71AB) replacement Step Description Put the disk into an Only mode. Enter (at the terminal): >DISK MODE xx (cr) where: xx = disk mode = AO = A ONLY (if you are changing out the B power supply). = BO = B ONLY (if you are changing out the A power supply).
  • Page 643 Section 060-INDP-610 Maintenance Procedures Guide 6-205 Procedure 6-47 Power supply (NT6M71AB) replacement Step Description Loosen the slotted-head captive screw at the bottom of the power supply. Gently pull the power supply out of the chassis. Make sure the three connectors (and cables) are out of the way during removal of the power supply unit.
  • Page 644 6-206 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-47 Power supply (NT6M71AB) replacement Step Description Make the disk system redundant. At the maintenance terminal, enter: >DISK MODE xx (cr) where: xx = disk mode = AP = A PRIME (if mode is A only) = BP = B PRIME (if mode is B only) The DPP will begin a disk copy, this may take several hours, depending on how much data is stored and the capacity of the disks.
  • Page 645: Remove Disk Drive (Nt6M72Ga)

    Section 060-INDP-610 Maintenance Procedures Guide 6-207 Disk Drive Replacement (NT6M72GA) The status of the disk drives changes to B ONLY immediately when the main processor determines that the A disk drive has a non-recoverable fault condition. Verify the status of the disk drives by entering the DISK MODE command at the maintenance terminal.
  • Page 646 6-208 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-48 Remove Disk Drive (NT6M72GA) Step Description For the side that is operating in an ONLY disk mode, make sure that the other processor is active. The other processor is defined as that processor that does NOT have the failing disk drive in its chassis.
  • Page 647 Section 060-INDP-610 Maintenance Procedures Guide 6-209 Procedure 6-48 Remove Disk Drive (NT6M72GA) Step Description Disconnect the ribbon cable from J1; use the cables pull tab. Note the direction of the brown stripe on the cable (PIN 1). Remove the disk from the chassis. Place the disk on an antistatic surface. Fill out the disk drive fault analysis form and attach it to the disk drive (Sheet 3 of 3) Installing the Replacement Disk Drive...
  • Page 648: Install Replacement Disk Drive (Nt6M72Ga)

    6-210 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-49 Install Replacement Disk Drive (NT6M72GA) Step Description Keeping the disk drive level, slide it into position far enough to reconnect the ribbon cable at connector J1. Connect the ribbon cable to J1. WARNING The disk drive cannot operate if this cable is reversed.
  • Page 649 Section 060-INDP-610 Maintenance Procedures Guide 6-211 Procedure 6-49 Install Replacement Disk Drive (NT6M72GA) Step Description Make the disk system redundant by changing the ONLY disk mode to PRIME disk mode. Enter (at the terminal): >DISK MODE xP (cr) where x = currently active disk i.e., if DISK MODE is currently AO then type AP if DISK MODE is currently BO then type BP.
  • Page 650 6-212 Section 060-INDP-610 Maintenance Procedures Guide Procedure 6-49 Install Replacement Disk Drive (NT6M72GA) Step Description CAUTION These disk commands may cause a loss of data. Make sure the operational disk drive is in an ONLY mode before entering the following commands. Enter: (at the terminal) >DISK FORMAT x (cr) where: x = A for newly replaced disk A...
  • Page 651 DMS-10 Switch Specific Data This section contains information concerning the data pertinent to installing and testing a BMC chassis interfaced to a Nortel DMS-10 Digital Switching System. This information includes instructions and illustrations for physically connecting the TEC Tape Port and SDI Maintenance Terminal interfaces between the DMS-10 and the BMC, and also provides procedures for testing the integrity of the interface installations.
  • Page 652 7-2 Section 060-INDP-710 DMS-10 Switch Specific Data Figure 3-1 NT3T11 Interface Box Dimensions 19 in. (4892.6 mm) 11 in. 10 in. Top View 3.5 in. (88.9 mm) 26 in. (660.4 mm) Rear View 297-6201-502 Standard 01.02 September 2000...
  • Page 653 The Interface Boxes require connection of +12 V dc from the BMC chassis (J17) to power the NT3T11 circuit packs. Two red and black wire assemblies, Nortel part No. NT8M99AA, are furnished with the BMC equipment for this purpose. Refer to Figure 7-2.
  • Page 654 7-4 Section 060-INDP-710 DMS-10 Switch Specific Data Figure 3-1 NT3T11 12 VDC Power Cables P 15 33 inches 21 inches 297-6201-502 Standard 01.02 September 2000...
  • Page 655 Section 060-INDP-710 DMS-10 Switch Specific Data 7-5 Figure 3-1 NT3T11 - BMC Data Interface Cables W63P1 W63P9 (to J1 on top Interface Box) (to J9 on BMC chas- 4 feet W65P1 W65P10 (to J1 on bottom Interface Box) (to J10 on BMC chas- 4 feet BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 656 7-6 Section 060-INDP-710 DMS-10 Switch Specific Data 1.The circuitry in the NT3T11 pack is static-sensitive. Observe all precautions as relates to static-sensitive materials. 2.Remove the five Phillips-head screws from the front panel of the Interface Box and set aside. Refer to Figure 7-4. 3.Inside the enclosure, locate the two white guide rails, noting the notches on the inner side of the rails.
  • Page 657 Section 060-INDP-710 DMS-10 Switch Specific Data 7-7 Figure 3-1 Installing NT3T11 PCA in NT3T11 enclosure Enclosure with front cover removed Connector for PCA NT3T11 PCA located at rear inside component side up Guide rails for inserting NT3T11 PCA BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 658 7-8 Section 060-INDP-710 DMS-10 Switch Specific Data Figure 3-1 Installing NT3T11 Interface Box Mounting Brackets Tapped holes Holes in mounting Interface Box (rear) Screws furnished with 297-6201-502 Standard 01.02 September 2000...
  • Page 659 Section 060-INDP-710 DMS-10 Switch Specific Data 7-9 Figure 3-1 NT3T11 Interface Box connectors (rear view) For connection of 60-pin ribbon cable 3T12 CABLE A B A B For connection of For connection of 12 VDC power 72-pin NT3T12 cables cable BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 660 7-10 Section 060-INDP-710 DMS-10 Switch Specific Data Within the Interface Box, the input signals from the NT3T12 connector are fed to the NT3T11PCA, combined onto one ribbon cable, then fed to the 60- pin J1 connector. The +12 V dc is fed from the input connector to the PCA to power the NT3T11 circuitry.
  • Page 661 Section 060-INDP-710 DMS-10 Switch Specific Data 7-11 Figure 3-1 Connecting 12 VDC from BMC processor to NT3T11 Interface Boxes BLACK Power/Alarm Connector Top Interface Box A2 (rear BLACK To Pin Attach to DMS-10 logic ground after obtaining verification that office logic ground is iso- Power/Alarm Connector lated...
  • Page 662 7-12 Section 060-INDP-710 DMS-10 Switch Specific Data Figure 3-1 Connecting data ribbon cables from NT3T11 Interface Boxes to BMC processors Top Interface 3T12 CABLE (rear view) 60-Pin ribbon cable Remove and discard these screws. Attach the terminal lug from cables using the screws BMC, B Chassis 3T12 CABLE...
  • Page 663 Section 060-INDP-710 DMS-10 Switch Specific Data 7-13 Using the ribbon cable assembly labeled W63, connect the P1 connector to the J1 jack on the top Interface Box. Neatly route that ribbon cable up to the side of the BMC, connecting the P9 connector to the J9 jack on the B chassis of the BMC.
  • Page 664 7-14 Section 060-INDP-710 DMS-10 Switch Specific Data assigned to these 60-wire cables are listed in the pin connector chart. Refer to Table 7-1. Table 7-1 DMS-10/BMC TEC Ribbon Cable Pin/Signal Assignment Chart (for reference only) Signal Signal Signal /WRS /RD7 /FWD /WDP /RD6...
  • Page 665 Section 060-INDP-710 DMS-10 Switch Specific Data 7-15 Table 7-1 DMS-10/BMC TEC Ribbon Cable Pin/Signal Assignment Chart (for reference only) Signal Signal Signal /WDS /WD7 /RDP Sheet 2 of 2 Note: The “/” in front of the signal name indicates that the signal uses inverted logic.
  • Page 666 7-16 Section 060-INDP-710 DMS-10 Switch Specific Data Figure 3-1 Connecting DMS-10 Tape Port Cables to NT3T11 Interface Boxes From DMS-10 magnetic tape port Connect 72-pin NT3T12 cable Top Interface 3T12 CABLE (rear view) BMC Location Rear Interface 3T12 CABLE (rear view) From DMS-10 magnetic tape port Connect 72-pin NT3T12 cable 297-6201-502 Standard 01.02 September 2000...
  • Page 667 The DMS-10 provides a NT3T09 or NT3T80 SDI port for access to the BMC human/machine interface. The BMC A processor provides the appropriate J3 EIA jack for connecting the Maintenance Terminal. A cable assembly, Nortel part No. NT8M99AD, is provided for connecting the DMS-10 printer port to the BMC jack, according to the following instructions.
  • Page 668 7-18 Section 060-INDP-710 DMS-10 Switch Specific Data Figure 3-1 Connecting Cable (NT8M99AD) to DMS-10 SDI port Data and Peripheral Connector Plate on left side of BMC A chassis (viewed from To DMS-10 SDI port supplied cable on either NT3T09 or (NT8M99AD) To DMS-10 SDI Printer Crossover to J3 on...
  • Page 669 Section 060-INDP-710 DMS-10 Switch Specific Data 7-19 BMC/DMS-10 Interface Testing With the SDI port interface made, the DMS-10 terminal can now be used to test the integrity of the equipment and the interface connection, assuring that the DMS-10 terminal and the BMC can properly communicate with each other.
  • Page 670 7-20 Section 060-INDP-710 DMS-10 Switch Specific Data 2. Enter the following if not logged on: >LOGI (cr) The system responds as follows: PASS? 3.Type the DMS-10 password , followed by (cr); keys do not echo due to security. 4. A line of text (variable per system) prints out, followed by a line feed and #, to indicate user is now properly logged on and ready to input commands.
  • Page 671 Section 060-INDP-710 DMS-10 Switch Specific Data 7-21 Note: Up to six maintenance terminals can view BMC messages. When displaying multiple lines of text, response time is slowed. The more terminals assigned with this command, the slower the response time. 8.Save the DMS-10 password and terminal settings by entering the following: >MSG nn SITDAT WRITE (cr) Response: MSG FROM TTY nn SITDAT FILE DISK JOB COMPLETE...
  • Page 672 - two-digit DMS-10 terminal ID number (for a terminal ID already assigned), or two spaces (for an unused number), depending on the Nortel final test procedures. Use the DMS-10 two digit terminal IDs already decided upon (as shown above) for the aa through ff data in the following entries to assign or change the current assignments in the table.
  • Page 673 Section 060-INDP-710 DMS-10 Switch Specific Data 7-23 where: 1 - first terminal listing in the table aa - ID number assigned as the first terminal in the DMS-10 system. For the second terminal in the table, enter the following: >MSG nn DMST 2 bb (cr) where: 2 - second terminal listing in the table aa - ID number assigned as second terminal in the DMS-10 system.
  • Page 674 B13 and B12 PCAs. Failure at any step indicates a faulty PCA or faulty wiring on backplane of the active processor. Report any defect to Nortel Technical Support. TEC-DMS-10 Interface Testing It is expected that the DSM-10 user is already familiar with various DMS-10 magnetic tape commands;...
  • Page 675 Section 060-INDP-710 DMS-10 Switch Specific Data 7-25 Make the same checks on the other tape port by entering the following on the DMS-10 terminal: (to check ON LINE, NOT BUSY, and WRITE ENABLE) >ENBL MTU 1 (cr) (to write a test pattern) >TEST MTU 1 (cr) (to read three blocks, check expiration date, write creation >SEIZE MTU 1 (cr)
  • Page 676 7-26 Section 060-INDP-710 DMS-10 Switch Specific Data Figure 3-1 Peripheral Interfaces for BMC-DMS-10 system Not Available Software Download SDI Port Maintenance Port 1 TEC 1 (slot 13; A and B chassis) TEC 0 (slot 12; A and B chassis) V.35 Link 1 (9600 baud maximum) V.35 Link 2 (9600 baud maximum) RS-232 Link 1 (9600 baud maximum) RS-232 Link 2 (9600 baud maximum)
  • Page 677 Section 060-INDP-710 DMS-10 Switch Specific Data 7-27 Table 7-2 Connector to Quad SIO PCA Cross-Reference BMC connectors on side Quad SIO PCA settings of A chassis Connecto Function Rotary Switch Option Jumpers Definitions # Settings MTC PTR 1 S5 - Baud 4 J81-2External Transmit Timing* Asychronous 5 - 300...
  • Page 678 7-28 Section 060-INDP-710 DMS-10 Switch Specific Data Table 7-2 Connector to Quad SIO PCA Cross-Reference BMC connectors on side Quad SIO PCA settings of A chassis Connecto Function Rotary Switch Option Jumpers Definitions # Settings Note 6: This PCA supports polling on digital data lines or on analog network. For digital data lines check that: a.
  • Page 679 Section 060-INDP-710 DMS-10 Switch Specific Data 7-29 Figure 3-1 Quad SIO PCA (A6 and B6) options (NT6M60BA) J5 J4 BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 680 7-30 Section 060-INDP-710 DMS-10 Switch Specific Data Figure 3-1 Quad SIO PCA (NT6M60BA) baud rate selector switches Quad SIO printed circuit assembly in slots A6 and B6 Baud 4 (S5) MTC PTR 1 Baud 3 (S4) SDI Port Baud 2 (S3) Software Download Baud 1 (S2) Not available...
  • Page 681 DMS-100 Switch Specific Data This document contains information concerning the switch-specific data pertinent to installing and testing a BMC chassis interfaced to a Nortel DMS-100 Digital Switching System. This information includes instructions and illustrations for physically connecting the DSI - Tape Port and maintenance terminal interfaces between the DMS-100 and the BMC, and provides procedures for testing the integrity of the interface installations.
  • Page 682 8-2 Section 060-INDP-711 DMS-100 Switch Specific Data Figure 3-1 Interface Box Dimensions (Top and Front Views) 19 in. (4892.6 mm) 13-1/2 12-3/4 4-5/16 in. 4-1/8 in. Top View 2-1/2 in. (63.5 mm) 17-1/2 in. (444.5 mm) 25-3/4 in. (654 mm) Front View 297-6201-502 Standard 01.02 September 2000...
  • Page 683 Section 060-INDP-711 DMS-100 Switch Specific Data 8-3 Figure 3-1 Interface Box Connectors Connects Control Cable Connects Read Cable from DMS-100 Tape Connects Control Cable Connects Read Cable J3 CONTROL J3 CONTROL J1 READ J1 READ J1 WRITE J1 WRITE J4 BMC/DPP J4 BMC/DPP Connects Write Cable Connects 60-wire ribbon...
  • Page 684 8-4 Section 060-INDP-711 DMS-100 Switch Specific Data Within the Interface Box, the input signals from the J1, J2, and J3 connectors at the left are combined to form a single ribbon cable, and fed to the 60-pin J4 BMC connector at the left. The J1, J2, and J3 signals connected at the right are combined on another cable and fed to the 60-pin J4 BMC connector at the right.
  • Page 685 Section 060-INDP-711 DMS-100 Switch Specific Data 8-5 Figure 3-1 Installing Interface Box Mounting Brackets Tapped holes Holes in mounting Interface Box (rear) Screws furnished with BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 686 8-6 Section 060-INDP-711 DMS-100 Switch Specific Data Figure 3-1 Interface Box - BMC Data Interface Cables W63P4 W63P9 (to J4, port 1 on top Interface (to J9 on BMC chas- 4 feet W65P4 W65P10 (to J4, port 0 on bottom Interface (to J10 on BMC chas- Box) 4 feet...
  • Page 687 Section 060-INDP-711 DMS-100 Switch Specific Data 8-7 Figure 3-1 Connecting ribbon cables between Interface Box and BMC chassis Remove and discard these screws. Attach the terminal lugs B Chassis 60-pin ribbon cables J3 CONTROL J3 CONTROL J1 READ J1 READ J1 WRITE J1 WRITE J4 BMC/DPP...
  • Page 688 8-8 Section 060-INDP-711 DMS-100 Switch Specific Data From J4, 60-pin ribbon cable header, on right rear of Interface Box, connect ribbon cable to the J9 connector on the side panel of the B BMC chassis. Remove and discard the screw to the left of the J9 connector. Attach the terminal lug from the cable using the screw supplied with the cable.
  • Page 689 Section 060-INDP-711 DMS-100 Switch Specific Data 8-9 Table 8-1 DMS-100/BMC DSI Ribbon Cable Pin/Signal Assignment Chart (for reference only) Signal Signal Signal /CER /FWD /REWS /RDYS /BOTS /ONLS /FPRS /EOTS /RDS /WDS /EOB /IDB/CRC /WENS Sheet 2 of 2 Note: The “/” in front of the signal name indicates that the signal uses inverted logic.
  • Page 690 8-10 Section 060-INDP-711 DMS-100 Switch Specific Data Maintenance Terminal Information This system can accept up to three maintenance terminals to provide human- to-machine communications with the BMC. Communications with the BMC include such procedures as entering or changing site dependent data, requesting certain system operations, outputting specified statistical reports, and providing maintenance messages that indicate system operating conditions.
  • Page 691 Section 060-INDP-711 DMS-100 Switch Specific Data 8-11 Figure 3-1 Connection DMS-100 Tape Port Cables to Interface Box Connect Read, Write, and Connect Read, Write, and Control Cables from DMS-100 Control Cables from DMS-100 Tape Port 0 Tape Port 1 J3 CONTROL J3 CONTROL J1 READ J1 READ...
  • Page 692 The BMC provides facilities for the connection of up to three maintenance terminals. At least one must be used. The customer is responsible for providing the maintenance terminals. Nortel provides an NT8M99AB cable for DTE connection to one maintenance terminal. The NT8M99AB cable has a DB25P (male) connector at the BMC end of the cable.
  • Page 693 B13 and B12 PCAs. A failure at any step indicates a faulty PCA or faulty wiring on the backplane of the processor that is on-line. Report any defect to Nortel. DSI-DMS-100 Interface Testing It is expected that the DMS-100 user is already familiar with various DMS- 100 magnetic tape commands;...
  • Page 694 8-14 Section 060-INDP-711 DMS-100 Switch Specific Data Note: The following command entries do not provide a thorough test of AMA. Refer to the appropriate DMS-100 documentation for a comprehensive list of test command entries and mounting of AMA ports. Enter the following on the DMS-100 Maintenance and Administration Position (MAP) terminal: >MAPCI;MTC;IOD;IOC m;CARD n;BSY;TST;RTS (cr) where:...
  • Page 695 Section 060-INDP-711 DMS-100 Switch Specific Data 8-15 Figure 3-1 Peripheral Interfaces for BMC-DMS-100 system Maintenance Printer 3 Software Download Maintenance Printer 2 Maintenance Printer 1 DSI 1 (slot 13; A and B chassis) DSI 0 (slot 12; A and B chassis) V.35 Link 1 (9600 baud maximum) V.35 Link 2 (9600 baud maximum) RS-232 Link 1 (9600 baud maximum)
  • Page 696 8-16 Section 060-INDP-711 DMS-100 Switch Specific Data Table 8-2 Connector to Quad SIO PCA Cross-Reference BMC connectors on side Quad SIO PCA settings of A chassis Connecto Function Rotary Switch Option Jumpers Definitions # Settings MTC PTR 1 S5 - Baud 4 J81-2External Transmit Timing* Asychronous 5 - 300...
  • Page 697 Section 060-INDP-711 DMS-100 Switch Specific Data 8-17 Table 8-2 Connector to Quad SIO PCA Cross-Reference BMC connectors on side Quad SIO PCA settings of A chassis Connecto Function Rotary Switch Option Jumpers Definitions # Settings * factory setting for this switch or jumper. Note 7: This PCA supports polling on digital data lines or on analog network.
  • Page 698 8-18 Section 060-INDP-711 DMS-100 Switch Specific Data Figure 3-1 Quad SIO PCA (A6 and B6) options (NT6M60BA) J5 J4 297-6201-502 Standard 01.02 September 2000...
  • Page 699 Section 060-INDP-711 DMS-100 Switch Specific Data 8-19 Figure 3-1 Quad SIO PCA (NT6M60BA) baud rate selector switches Quad SIO printed circuit assembly in slots A6 and B6 Baud 4 (S5) MTC PTR 1 Baud 3 (S4) MTC PTR 2 Baud 2 (S3) Software Download Baud 1 (S2) MTC PTR 3...
  • Page 701 List of terms List of terms Alternating Current Automatic Dial-Up Automatic Message Accounting An automatic recording system that documents all of the necessary billing data of subscriber-dialed long distance. ASCII American Standard Code for Information Interchange Allocation Unit American Wire Gauge Binary Coded Decimal BELLCORE Bell Communications Research...
  • Page 702 9-2 List of terms Billing Media Converter A peripheral device of the Switching System that functions as an AMA data collector and transmitter. The BMC collects AMA data from the switch, formats the data, stores the data on its own internal disk and transmits the data to a data collection center when polled by the collection center.
  • Page 703 List of terms 9-3 DRAM Dynamic Random Access Memory A Random Access Memory system that employs transistor capacitor storage cells. The logic state is stored in the capacitor and buffered by the transistor. The capacitive charge is only held for a short duration and must be refreshed at a periodic rate to maintain it programmed state.
  • Page 704 9-4 List of terms Integrated Circuit Installation Manual Input/Output Input/Output Controller Input/Output Equipment International Standards Organization Light-Emitting Diode LSSGR LATA Switching System Generic Requirements Lamp Test Maintenance and Administration Position Man-Machine Interface Main Processor Magnetic Tape Drive Magnetic Tape Port 297-6201-502 Standard 01.02 September 2000...
  • Page 705 List of terms 9-5 Magnetic Tape Unit Northern Telecom Practices Programmed Assembly Logic Printed Circuit Assembly Product Equipment Code Parallel Input/Output PROM Programmable Read-Only Memory Random Access Memory Revenue Accounting Office Record Descriptor Word Reliable File Transfer Read-Only Memory Serial Controller Chip SCSI Small Computer System Interface BMC II BISYNC Operation, Administration, and Maintenance Guide BMCB001 and up...
  • Page 706 9-6 List of terms Serial Data Interface Serial Input/Output Circuitry in the BMC that passes data from the BMC to external devices. The BMC employs four such circuits in its Quad SIO PCA that provides communications paths between the BMC, the Switching System maintenance terminals, and the remote polling center link.
  • Page 708 Except as expressly authorized in writing by Nortel Networks, the holder is granted no rights to use the information contained herein. Information is subject to change without notice. Nortel Networks reserves the right to make changes in design or components as progress in engineering and manufacturing may warrant.

This manual is also suitable for:

Dms-100 series

Table of Contents

Save PDF