Toshiba e-STUDIO556 Service Manual page 562

Error code Classification
E775 RADF jam
E777
E860
E870
E871
E890
E9F0 Finisher jam
(Puncher section)
EA10 Finisher jam
(Finisher section)
EA20
EA30
EA40
EA50
EA60
EA80 Finisher jam
(Saddle Stitcher
EA90
section)
EAA0
EAB0
EAC0
EAD0 Other paper jam
EAE0 Finisher jam
EB30
EB50 Paper transport jam
EB60
e-STUDIO556/656/756/856/557/657/757/857
ERROR CODE AND TROUBLESHOOTING
Contents
Original reading end sensor paper remaining jam
Original exit sensor paper remaining jam
Original jam access cover open: The Original jam
access cover has opened during RADF operation.
RADF open jam: RADF has opened during RADF
operation.
Cover open jam in the read ready status: Jam
caused by opening of the Original jam access cover
or front cover while the RADF is waiting for the
scanning start signal from the equipment.
ADF time out jam
Hole punch jam: Hole punching is not performed
properly.
Paper transport delay jam: Paper which has passed
the exit sensor does not reach the inlet sensor.
Paper transport stop jam: Paper which has reached
the inlet sensor does not pass the inlet sensor.
Power-ON jam: Paper is remaining at the inlet
sensor when the power is turned ON.
Door open jam: The upper cover or the front cover
of the Finisher has opened, or the upper door or the
front door of the Hole Punch Unit has opened
during printing.
Stapling jam: Stapling is not performed properly.
Early arrival jam: The inlet sensor detects paper
earlier than the specified timing.
Stapling jam: Stapling is not performed properly.
Door open jam: The delivery cover or the inlet cover
has opened during printing.
Power-ON jam: Paper is remaining at the No. 1
paper sensor, No. 2 paper sensor, No. 3 paper
sensor, vertical path paper sensor or delivery
sensor when the power is turned ON.
Paper transport stop jam: Paper which has passed
the inlet sensor does not reach or pass the No. 1
paper sensor, No. 2 paper sensor, No. 3 paper
sensor or delivery sensor.
Transport delay jam: Paper which has reached the
inlet sensor does not pass the inlet sensor.
Print end command time-out jam: The printing has
not finished normally due to the communication
error between the SYS board and LGC board at the
end of the printing.
Receiving period time-out jam: The printing cannot
be finished normally due to the communication
error between the equipment and the Finisher when
the paper is transported from the equipment to the
Finisher.
Ready period time-out jam: The equipment judges
that the paper transport to the Finisher is disabled
due to the communication error between the
equipment and the Finisher at the start of the
printing.
Paper remaining on the transport path: The multiple
feeding of the preceding paper caused the
misfeeding of the upcoming paper.
Paper remaining on the transport path: The multiple
feeding of the preceding paper caused the
misfeeding of the upcoming paper (= re-detection
after no jam is detected at [EB50]).
© 2011 - 2014 TOSHIBA TEC CORPORATION All rights reserved
8 - 10
Troubleshooting
P. 8-71
P. 8-71
P. 8-72
P. 8-72
P. 8-72
P. 8-72
P. 8-73
P. 8-73
P. 8-74
P. 8-75
P. 8-76
P. 8-77
P. 8-77
P. 8-78
P. 8-79
P. 8-80
P. 8-81
P. 8-82
P. 8-86
P. 8-86
P. 8-87
P. 8-57
P. 8-58