Parameters (Functions) And Instruction Codes Under Different Control Methods - Mitsubishi Electric FR-F820-00046 Instruction Manual

9.3
Parameters (functions) and instruction codes
under different control methods
*1 Instruction codes are used to read and write parameters in accordance with the Mitsubishi inverter protocol of RS-485 communication. (For RS-
485 communication, refer to
*2 Function availability under each control method is shown as follows:
○: Available
×: Not available
*3 For Parameter copy, Parameter clear, and All parameter clear, ○ indicates the function is available, and × indicates the function is not available.
*4 Communication parameters that are not cleared by parameter clear or all clear (H5A5A or H55AA) via communication. (For RS-485
communication, refer to
*5 When a communication option is installed, parameter clear (lock release) during password lock (Pr.297 Password lock/unlock ≠ "9999") can be
performed only from the communication option.
*6 Reading and writing via the PU connector are available.
Symbols in the table indicate parameters that operate when the options are connected.
FR-A8AR, FR-A8AX,
A8NL
Pr.
0 Torque boost
1 Maximum frequency
2 Minimum frequency
3 Base frequency
4 Multi-speed setting (high speed)
5 Multi-speed setting (middle speed)
6 Multi-speed setting (low speed)
7 Acceleration time
8 Deceleration time
9 Electronic thermal O/L relay
DC injection brake operation
10
frequency
11 DC injection brake operation time
12 DC injection brake operation voltage
13 Starting frequency
14 Load pattern selection
15 Jog frequency
16 Jog acceleration/deceleration time
17 MRS input selection
18 High speed maximum frequency
19 Base frequency voltage
Acceleration/deceleration reference
20
frequency
Acceleration/deceleration time
21
increments
22 Stall prevention operation level
Stall prevention operation level
23
compensation factor at double speed
24 Multi-speed setting (speed 4)
25 Multi-speed setting (speed 5)
26 Multi-speed setting (speed 6)
27 Multi-speed setting (speed 7)
Multi-speed input compensation
28
selection
Acceleration/deceleration pattern
29
selection
30 Regenerative function selection
31 Frequency jump 1A
32 Frequency jump 1B
638
9. APPENDIX

9.3 Parameters (functions) and instruction codes under different control methods

page 482.)
page 482.)
FR-A8AY, FR-A8NC,
Instruction code
Name
Read Write
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
FR-A8NCE, FR-A8ND,
*1
Control method
Exte
Magnetic flux Magnetic flux Magnetic flux
V/F V/F V/F
nded
80 0 ○
81 0 ○
82 0 ○
83 0 ○
84 0 ○
85 0 ○
86 0 ○
87 0 ○
88 0 ○
89 0 ○
8A 0 ○
8B 0 ○
8C 0 ○
8D 0 ○
8E 0 ○
8F 0 ○
90 0 ○
91 0 ○
92 0 ○
93 0 ○
94 0 ○
95 0 ○
96 0 ○
97 0 ○
98 0 ○
99 0 ○
9A 0 ○
9B 0 ○
9C 0 ○
9D 0 ○
9E 0 ○
9F 0 ○
A0 0 ○
FR-A8NP, FR-A8NF,
*2
Parameter
*3
Copy
PM PM PM
× × ○
○ ○ ○
○ ○ ○
× × ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ × ○
○ ○ ○
× × ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
× × ○
○ ○ ○
○ ○ ○
○ ○ ○
○ × ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
○ ○ ○
FR-
All
*3
Clear
*3
clear
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○