Monitor Item Selection On Operation Panel Or Via Communication - Mitsubishi Electric FR-F820-00046 Instruction Manual

Parameters referred to
Pr.1 Maximum frequencypage 271
Pr.52 Operation panel main monitor
Pr.81 Number of motor polespage 169
Pr.800 Control method selectionpage 169
5.8.2 Monitor item selection on operation panel or via
communication
The monitor item to be displayed on the operation panel or the parameter unit can be selected.
Pr. Name
52 Operation panel main
M100 monitor selection
774 Operation panel monitor
M101 selection 1
775 Operation panel monitor
M102 selection 2
776 Operation panel monitor
M103 selection 3
992 Operation panel setting dial
M104 push monitor selection
170
Watt-hour meter clear
M020
563 Energization time carrying-
M021 over times
268 Monitor decimal digits
M022 selection
891 Cumulative power monitor
M023 digit shifted times
171
Operation hour meter clear 9999
M030
564 Operating time carrying-
M031 over times
290 Monitor negative output
M044 selection
1018
Monitor with sign selection 9999
M045
1106
Torque monitor filter
M050
1107 Running speed monitor
M051 filter
1108 Excitation current monitor
M052 filter
288
5. PARAMETERS
5.8 (M) Item and output signal for monitoring
selectionpage 288
Initial value Setting range
0, 5 to 14, 17, 18,
20, 23 to 25, 34, 38,
0 (output
40 to 45, 50 to 57,
frequency)
61, 62, 64, 67 to 69,
81 to 96, 98, 100
1 to 3, 5 to 14, 17,
18, 20, 23 to 25, 34,
38, 40 to 45, 50 to
9999
57, 61, 62, 64, 67 to
69, 81 to 96, 98,
100, 9999
0 to 3, 5 to 14, 17,
18, 20, 23 to 25, 34,
0 (set 38, 40 to 45, 50 to
frequency) 57, 61, 62, 64, 67 to
69, 81 to 96, 98,
100
0
10
9999
9999
(0 to 65535)
0
(Read-only)
0
9999 1
9999
0 to 4
9999
9999
0
9999
(0 to 65535)
0
(Read-only)
0 0 to 7
0
9999
0 to 5 s
9999
9999
0 to 5 s
9999
9999
0 to 5 s
9999
9999
Description
Select the item monitored on the operation panel or
parameter unit.
Refer to page 289 for the monitor item selection.
Each of the initial items monitored on the operation panel or
parameter unit in the monitor mode (output frequency,
output current, and output voltage) can be switched to a
user-designated item.
9999: Follows the Pr.52 setting.
Select the monitor item displayed on the operation panel at
the time when the setting dial is pressed.
Set "0" to clear the watt-hour meter.
Set "10" to monitor the cumulative power in the range of 0 to
9999 kWh via communication.
Set "9999" to monitor the cumulative power in the range of 0
to 65535 kWh via communication.
The number of times that the cumulative energization time
exceeded 65535 hours is displayed (read-only).
Value is displayed in 1 increments (an integer).
Value is displayed in 0.1 increments.
No function
Set the number of digits to move the decimal point of the
cumulative energy monitored value to the left.
The readout peaks out at the upper limit of readout.
The function of moving the decimal point is not available.
The readout is reset to 0 when it exceeds the upper limit.
Set "0" to clear the operation hour meter.
The readout is always 9999. Nothing changes when "9999"
is set.
The number of times that the operating time reaches 65535
hours is displayed. Read-only.
Set the availability of negative signals output via terminal
AM, to the operation panel, and through communication.
Select the item group to enable the indication of negative
signed numbers.
The filter time constant is selectable for monitoring of the
torque. A larger setting results in slower response.
0.3 s filter
The filter time constant is selectable for monitoring of the
running speed. A larger setting results in slower response.
0.08 s filter
The filter time constant is selectable for monitoring of the
motor excitation current. A larger setting results in slower
response.
0.3 s filter