Input Terminal Function Selection - Mitsubishi Electric FR-F820-00046 Instruction Manual

5.9.8

Input terminal function selection

Use the following parameters to select or change the input terminal functions.
Pr. Name
178 STF terminal
T700 function selection
179 STR terminal
T701 function selection
180 RL terminal function
T702 selection
181 RM terminal function
T703 selection
182 RH terminal function
T704 selection
183 RT terminal function
T705 selection
184 AU terminal function
T706 selection
185 JOG terminal
T707 function selection
186 CS terminal function
T708 selection
187 MRS terminal
T709 function selection
188 STOP terminal
T710 function selection
189 RES terminal
T711 function selection
Pr. Name
699
Input terminal filter
T740
*1 The initial value is for standard models and IP55 compatible models.
*2 The initial value is for separated converter types.
 Input terminal function assignment
• Use Pr.178 to Pr.189 to set the functions of the input terminals.
• Refer to the following table and set the parameters.
Signal
Setting
name
Pr.59 = 0 (initial value)
0 RL
Pr.59 ≠ 0
Pr.59 = 0 (initial value)
1 RM
Pr.59 ≠ 0
Pr.59 = 0 (initial value)
2 RH
Pr.59 ≠ 0
3 RT Second function selection
4 AU Terminal 4 input selection
5 JOG Jog operation selection
Selection of automatic restart after instantaneous power failure /
flying start
6 CS
Electronic bypass function
7 OH
External thermal relay input
Initial
Initial signal
value
60 STF (Forward rotation command)
61 STR (Reverse rotation command)
0 RL (Low-speed operation command)
1 RM (Middle-speed operation command)
2 RH (High-speed operation command)
3 RT (Second function selection)
4 AU (Terminal 4 input selection)
5 JOG (Jog operation selection)
9999 No function
*1
MRS (Output stop)
24
*2
X10 (Inverter run enable)
10
25 STP (STOP) (Start self-holding selection)
62 RES (Inverter reset)
Initial
Setting range
value
5 to 50 ms
9999
9999
Function
Low-speed operation command
*1
Remote setting (setting clear)
Middle-speed operation
command
*1
Remote setting (deceleration)
High-speed operation command
*1
Remote setting (acceleration)
*2
0 to 8, 10 to 14, 16, 18, 24, 25, 28, 37 to 40, 46
to 48, 50, 51, 57, 58, 60, 62, 64 to 67, 70 to 73,
77 to 81, 84, 94 to 98, 9999
0 to 8, 10 to 14, 16, 18, 24, 25, 28, 37 to 40, 46
to 48, 50, 51, 57, 58, 61, 62, 64 to 67, 70 to 73,
77 to 81, 84, 94 to 98, 9999
0 to 8, 10 to 14, 16, 18, 24, 25, 28, 37 to 40, 46
to 48, 50, 51, 57, 58, 62, 64 to 67, 70 to 73, 77
to 81, 84, 94 to 98, 9999
Description
Set the time delay for the input terminal response.
No filter for the input terminal
Related parameter
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.59
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.59
Pr.4 to Pr.6, Pr.24 to Pr.27,
Pr.232 to Pr.239
Pr.59
Pr.44 to Pr.51, Pr.450 to
Pr.463, Pr.569, Pr.832, etc.
Pr.267
Pr.15, Pr.16
Pr.57, Pr.58, Pr.162 to
Pr.165, Pr.299, Pr.611
Pr.57, Pr.58, Pr.135 to
Pr.139, Pr.159
Pr.9
5.9 (T) Multi-function input terminal parameters
Setting range
Refer to
page
249
222
249
222
249
222
358
330
248
446, 451
387
252
355
5. PARAMETERS
1
2
3
4
5
6
7
8
9
10