Mitsubishi Electric FR-F820-00046 Instruction Manual page 166

 N: Communication operation
parameters
Parameters for the setting of communication operation such
as the communication
characteristics.
Pr.
Pr.
group
N000 549 Protocol selection
Communication EEPROM write
N001 342
selection
MODBUS RTU communication
N002 539
check time interval
Stop mode selection at
N013 502
communication error
Operation frequency during
N014 779
communication error
N020 117 PU communication station number
N021 118 PU communication speed
N022 119 PU communication data length
N023 119 PU communication stop bit length
N024 120 PU communication parity check
N025 121 PU communication retry count
PU communication check time
N026 122
interval
PU communication waiting time
N027 123
setting
PU communication CR/LF
N028 124
selection
RS-485 communication station
N030 331
number
N031 332 RS-485 communication speed
RS-485 communication data
N032 333
length
RS-485 communication stop bit
N033 333
length
RS-485 communication parity
N034 334
check selection
N035 335 RS-485 communication retry count
RS-485 communication check time
N036 336
interval
RS-485 communication waiting
N037 337
time setting
RS-485 communication CR/LF
N038 341
selection
USB communication station
N040 547
number
USB communication check time
N041 548
interval
N050 726 Auto Baudrate/Max Master
N051 727 Max Info Frames
Device instance number (Upper 3
N052 728
digits)
Device instance number (Lower 4
N053 729
digits)
N054 390 % setting reference frequency
N080 343 Communication error count
N500 to 1300 to
Communication option parameters.
N543, 1343,
For details, refer to the Instruction Manual
N550 to 1350 to
of the option.
N559 1359
specifications or operating
Refer
Name
to page
478,
511
478
498
478
478
482
482
482
482
482
482
482
482
482
482,
511
482,
511
482
482
482
482
482
482
482
523
523
511
511
511
511
511
498
 G: Control parameters
Parameters for motor control.
Pr.
Pr.
group
G000 0
Torque boost
G001 3
Base frequency
G002 19 Base frequency voltage
G003 14 Load pattern selection
G010 46 Second torque boost
G011 47 Second V/F (base frequency)
G030 60 Energy saving control selection
G040 100 V/F1 (first frequency)
G041 101 V/F1 (first frequency voltage)
G042 102 V/F2 (second frequency)
G043 103 V/F2 (second frequency voltage)
G044 104 V/F3 (third frequency)
G045 105 V/F3 (third frequency voltage)
G046 106 V/F4 (fourth frequency)
G047 107 V/F4 (fourth frequency voltage)
G048 108 V/F5 (fifth frequency)
G049 109 V/F5 (fifth frequency voltage)
SF-PR slip amount adjustment
G060 673
operation selection
SF-PR slip amount adjustment
G061 674
gain
Reverse rotation excitation current
G080 617
low-speed scaling factor
DC injection brake operation
G100 10
frequency
G101 11 DC injection brake operation time
G105 522 Output stop frequency
G106 250 Stop selection
*2
G107 Parameter for manufacturer setting. Do not set.
70
DC injection brake operation
G110 12
voltage
Regeneration avoidance operation
G120 882
selection
Regeneration avoidance operation
G121 883
level
Regeneration avoidance at
G122 884
deceleration detection sensitivity
Regeneration avoidance
G123 885 compensation frequency limit
value
Regeneration avoidance voltage
G124 886
gain
Regeneration avoidance
G125 665
frequency gain
Increased magnetic excitation
G130 660
deceleration operation selection
G131 661 Magnetic excitation increase rate
Increased magnetic excitation
G132 662
current level
G200 800 Control method selection
G201 85 Excitation current break point
Excitation current low-speed
G202 86
scaling factor
G203 245 Rated slip
G204 246 Slip compensation time constant
Constant output range slip
G205 247
compensation selection
G211 820 Speed control P gain 1
Refer
Name
to page
Simple Simple Simple 527
Simple Simple Simple 528
528
530
527
528
532
533
533
533
533
533
533
533
533
533
533
534
534
531
535
535
536
538
535
545
545
545
545
545
545
547
547
547
169
531
531
548
548
548
182
5. PARAMETERS
5.1 Parameter list
1
2
3
4
5
6
7
8
9
10
165