Mitsubishi Electric FR-F820-00046 Instruction Manual page 292

Increment
Monitor item
and unit
PID input pressure
0.1%
value
32-bit cumulative
1 kWh
energy (lower 16 bits)
32-bit cumulative
1 kWh
energy (upper 16 bits)
0.01/0.1
32-bit cumulative
*5
energy (lower 16 bits)
kWh
0.01/0.1
32-bit cumulative
*5
energy (upper 16 bits)
kWh
BACnet reception
1
status
BACnet token pass
1
counter
BACnet valid APDU
1
counter
BACnet
communication error 1
counter
BACnet terminal FM/
0.1%
CA output level
BACnet terminal AM
0.1%
output level
Remote output value
0.1%
1
Remote output value
0.1%
2
Remote output value
0.1%
3
Remote output value
0.1%
4
PID manipulated
0.1%
amount
Second PID set point 0.1%
Second PID
0.1%
measured value
Second PID deviation 0.1%
Second PID
0.1%
measured value 2
Second PID
0.1%
manipulated amount
Control circuit
1°C
temperature
*1 To monitor the item on the LCD operation panel (FR-LU08) or the parameter unit (FR-PU07) in the monitor mode, use Pr.774 to Pr.776 or the
monitor function of the FR-LU08 or the FR-PU07 for setting.
*2 The cumulative energization time and actual operation time are accumulated from 0 to 65535 hours, then cleared, and accumulated again from 0.
*3 The actual operation time does not increase if the cumulative running time before power OFF is less than an hour.
*4 On the parameter unit (FR-PU07), the unit "kW" is displayed.
*5 The increment differs according to the inverter capacity. (FR-F820-02330(55K) or lower, FR-F840-01160(55K)or lower / FR-F820-03160(75K) or
higher, FR-F840-01800(75K) or higher)
*6 Since each readout of the output voltage and output current displayed on the operation panel (FR-DU08) is a four-digit number, a value of more
than 9999 is displayed as "----".
*7 The setting is available for the standard model.
*8 The inverter regards the output current which is less than the specified current level (5% of the rated inverter current) as 0 A. Therefore, each
readout of an output current and output power may show "0" if a too small-capacity motor is used as contrasted with the inverter capacity and the
output current falls below the specified value.
*9 Available when the plug-in option is connected.
Negative
Pr. MODBUS
RS-485 indication
setting RTU
69 H45 40269
— H4D 40277
— H4E 40278
— H4F 40279
— H50 40280
81 H51 40281
82 H52 40282
83 H53 40283
84 H54 40284
85 H55 40285
86 H56 40286 ○
87 H57 40287
88 H58 40288
○
89 H59 40289
90 H5A 40290
91 H5B 40291 ○
92 H5C 40292
93 H5D 40293
94 H5E 40294 ○
95 H5F 40295
96 H60 40296 ○
98 H62 40298 ○
Description
(-)
Displays the input pressure value of the PID input
pressure control function.
The upper or lower 16 bits of the 32-bit cumulative
energy is displayed on each indication.
It is monitored via RS-485 communication or other
communication with a communication option installed.
(To find the monitor codes for each communication
option, refer to the Instruction Manual of each
communication option.)
Displays the BACnet reception status.
Displays the count of received token.
Displays the count of valid APDU detection.
Displays the count of communication error detection.
Displays the value set in the Analog Output object (ID=0:
Terminal FM/CA) for BACnet communication.
Displays the value set in the Analog Output object (ID=1:
Terminal AM) for BACnet communication. (A display
without signs displays negative values as absolute
values.)
Displays the value set in Pr.656 to Pr.659 (analog
remote output). (Refer to
The PID control manipulated amount is displayed. (Refer
to page 412.)
The set point, measured value, or deviation is displayed
during the second PID control operation. (Refer to
412.)
The PID measured value is displayed while the second
PID control is enabled (Pr.753 ≠ "0"), even if PID control
operating conditions are not satisfied. (Refer to
412.)
The second PID control manipulated amount is
displayed. (Refer to page
The temperature of the control circuit board is displayed.
(Refer topage 329.)
When negative number not displayed: 0 to 100°C
When negative number displayed: -20 to 100°C
5.8 (M) Item and output signal for monitoring
page 325.)
page
page
412.)
291
5. PARAMETERS
1
2
3
4
5
6
7
8
9
10