Keithley 4200A-SCS Reference Manual page 1379

Index
KCon configuration • 7-9, A-33
project to new name • 6-20
Schematic of pulse channel and connected DUT • 5-
67
SDM cycle • 3-39
seg_arb_define • 13-174
seg_arb_file • 13-177
seg_arb_sequence • 5-82, 13-133
seg_arb_waveform • 5-82, 13-136
SegARBConfig control type • 6-135
Segment Stress/Measure Mode • 6-184
Selecting • 6-153, 6-191, 6-193, 6-194, 6-195, 6-
320, G-28, H-21, I-5
Send device-dependent string • 13-35
SENSE LO terminal • 2-16, 3-13
SENSE terminal • 3-13, 3-18, 3-26
Sensing considerations • 3-32, 3-33, 3-34
serial connections • H-2
Serial polling • 9-56
series data, change display • 6-239
Set chuck heights • G-20
Set Component Mode • 13-137
Set integration time • 9-44
Set matrix card properties • A-32
Set Reference Die button • H-17
Set X, Y die size button • H-9
setmode • 5-82, 13-137
Setting up communication • G-7
Settings for Analyze sheet • 6-203
Settings worksheet • 6-203
Settling time • 6-112
Shielding • 2-2
short connection compensation data • 4-14
ShortCal4294 user module • 6-332
signal connections • E-2
signal connections, 8110A • E-2
signal integrity • 2-4
Signal limits, maximum • 2-1
signal paths • A-16, A-17
SIMCVsweep82 user module • D-18
Sink overview • 3-35
Site coordinate information • F-7
Sites • 6-152
SMU • 2-13, 2-14, 6-41, 7-13, 9-50
SMU connections • 2-1, 2-4, 2-5, 2-12, 2-14, A-7
SMU terminals and connectors • 2-15, 2-16, 3-
12, 3-13, 3-26
SMU with 4200-PA • 2-4, 2-17, 3-13, 3-15, 3-19
Compliance • 3-14
Software features • 1-4
Software versions • G-1
solarcell • 4-98
Source capacitance • 12-15
Source I measure I and source V measure V • 3-11
Source I, measure V or I • 3-37
Index-10
Model 4200A-SCS Parameter Analyzer Reference Manual
Source or sink • 3-4
Source resistance • 12-15
Source V, measure I or V • 3-37
Source-delay-measure cycle • 3-39
Source-measure concepts • 2-2, 2-13, 3-28, 3-29, 3-
30, 3-36, 3-37, 3-38, 12-11, 12-12, 12-13, 12-14,
12-15, 12-16, 12-17, 12-18
Low-current measurements • 12-11, 12-14, 12-15
Making stable measurements • 12-7, 12-8, 12-9,
12-10
Sensing considerations • 3-32, 3-33, 3-34
Source-Measure Unit (SMU) • 1-3
Basic SMU circuit configuration • 2-14
Operating boundaries • 3-4, 3-6, 3-8, 3-9, 3-11
Sink overview • 3-35
SMU terminals and connectors • 2-15, 2-16, 3-
12, 3-13, 3-26
source or sink • 3-4, 3-8, 3-10, 3-11
V-Source operation examples • 3-10
Speed scroll list • 6-89
Speed settings • 6-87, 6-89
Spline pattern window • H-17
Spot mean • 5-76
Starting KXCI and the GPIB command interpreter •
9-5
Starting the Formulator • 6-244
Status bar • 8-8
Status byte • 9-55
Status check box • 6-51
status-code bit map • 6-51
Step operation modes • 6-31, 6-39
stepping and sweeping • 6-23
Stepping and sweeping example • 6-23
Stressing • 6-166, 6-204, 6-205, 6-206, 6-242
submit device to a library • 6-320
Subsite Analyze sheet • 6-204, 6-205, 6-206, 6-242
Subsite cycling • 6-160, 6-164, 6-166, 6-171, 6-184,
6-196, 6-204, 6-205, 6-206, L-10
subsites • 6-153, 6-166, 6-195, 6-204, 6-205, 6-206
Suss Microtec Model PA-200 Prober • G-1, G-7, G-
15, G-16, G-29
Sweep concepts • 3-38, 3-39, 3-40, 4-6, 6-44
sweep system mode - VAR1 and VAR2 • 9-57
Sweep/step example • 9-17
Switch matrices • 3-32, 6-336, A-2, A-5, A-7, A-12,
A-13, A-15, A-16, A-25, A-29, A-31, A-32, A-33, A-
34
switch matrix, add • A-29
switch, with RPM • 5-8
synchronize graphs • 6-240
System Administration • 1-4, 11-2, 11-3
System Configuration information • 7-12
System Configuration Properties • 7-11
System mode commands • 9-13
System overview • 1-2
4200A-901-01 Rev. C / February 2017