Advertisement
Quick Links
A l l t e s t I n s t r u me n t s , I n c .
5 0 0 C e n t r a l A v e .
F a r mi n g d a l e , N J 0 7 7 2 7
P : ( 7 3 2 ) 9 1 9 - 3 3 3 9
F : ( 7 3 2 ) 9 1 9 - 3 3 3 2
a l l t e s t . n e t
s s a l e s @ a l l t e s t . n e t
T h e t e s t & me a s u r e me n t
e q u i p me n t y o u n e e d a t
t h e p r i c e y o u w a n t .
A l l t e s t c a r r i e s t h e w o r l d ' s l a r g e s t s e l e c t i o n o f
u s e d / r e f u r b i s h e d b e n c h t o p t e s t & me a s u r e me n t
e q u i p me n t a t 5 0 % t h e p r i c e o f n e w .
O O u r e q u i p me n t i s g u a r a n t e e d w o r k i n g , w a r r a n t i e d , a n d
a v a i l a b l e w i t h c e r t i f i e d c a l i b r a t i o n f r o m o u r i n - h o u s e s t a f f
o f t e c h n i c i a n s a n d e n g i n e e r s .
• 1 0 + f u l l t i me t e c h n i c i a n s w i t h o v e r 1 5 0 y e a r s o f
s p e c i a l i z a t i o n
• 9 0 d a y w a r r a n t y & 5 d a y r i g h t o f r e t u r n o n a l l
e q u i p me n t
• • 1 - 3 y e a r w a r r a n t i e s f o r n e w a n d
p r e mi u m- r e f u r b i s h e d e q u i p me n t
• E v e r y u n i t t e s t e d t o O E M s p e c i f i c a t i o n s
• S a t i s f a c t i o n g u a r a n t e e d
Y o u h a v e p l a n s , w e w i l l h e l p y o u a c h i e v e t h e m.
A n y p r o j e c t . A n y b u d g e t .
t
G e t a q u o t e t o d a y !
C C a l l ( 7 3 2 ) 9 1 9 - 3 3 3 9 o r e ma i l s a l e s @a l l t e s t . n e t .
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Keithley 4210-MMPC-S
Summary of Contents for Keithley 4210-MMPC-S
- Page 1 T h e t e s t & me a s u r e me n t e q u i p me n t y o u n e e d a t t h e p r i c e y o u w a n t . A l l t e s t I n s t r u me n t s , I n c .
- Page 2 I-V and C-V measurements using a single prober cable setup. It is also used with the Keithley Model 4200-PIV-A package to perform pulse I-V measurements. This kit has been assembled for use with the Suss Micro Tec PA200/300 prober series.
-
Page 3: Related Documents
The following documents (in PDF format) are located on the Model 4200 Complete Reference CD: • PA-993: This is a one-page packing list for the Model 4210-MMPC-S Multi-Measurement Prober Cable Kit for the Suss Micro Tec PA200/300 series prober. A photo shows all the components of the cable kit. - Page 4 Model 4210 MMPC-S Quick Start Guide I-V testing For I-V testing, connect the triax cables of your Model 4200 source-measure units (SMUs) to the standard female triax connectors on the bulkhead of the prober. Figure 3 shows two Model 4200 SMU prober connections. NOTE Figure 3 shows SMUs that do not use preamps.
- Page 5 Figure 4: Model 4210-CVU prober connections Pulse I-V testing using the Keithley Model 4200-PIV-A Perform 4-pin pulse I-V measurements using four prober cable kits with the Keithley Instruments Model 4200-PIV-A package, which includes a scope card, pulse generator card, software, and other components.
- Page 6 Model 4210 MMPC-S Quick Start Guide Figure 5: Model 4200-PIV-A instrumentation connections Figure 6: Cables and adapters used for instrumentation connections PA-1000 Rev. B / January 2010...
- Page 7 Model 4210 MMPC-S Quick Start Guide Installing the prober cable kits; basic cable setup Figure 7 shows the basic cable setup for the 2-pin I-V and C-V testing scenarios described in this guide. The 4-pin I-V and 4-pin C-V testing scenarios require minor setup changes; pulse I-V setup, which is more complex, is described later in this quick start guide.
- Page 8 Model 4210 MMPC-S Quick Start Guide • As shown in Figure 8, route the blue cables along the sides of the manipulators. Use the cable clamps to firmly secure the cables to the manipulators. Make sure the clamps are tight enough to keep the cables from moving.
-
Page 9: Usage Scenarios
Model 4210 MMPC-S Quick Start Guide Usage scenarios I-V testing: 2-pin I-V setup NOTE The setup for 2-pin I-V testing requires two prober cable kits. With two Model 4200-SMUs connected to the prober bulkhead, use the fundamental setup shown in Figure 10 to perform 2-pin I-V testing. - Page 10 Model 4210 MMPC-S Quick Start Guide Figure 11: Test setup for 4-pin I-V testing C-V testing: 2-pin C-V setup NOTE The setup for 2-pin C-V testing requires two prober cable kits. With a Model 4210-CVU connected to the prober bulkhead, use the fundamental setup shown in Figure 12 to perform 2-pin C-V testing.
- Page 11 With a Model 4200-CVU connected to the prober bulkhead, use the setup shown in Figure 13 to perform 4-pin C-V testing. Figure 13: Test setup for 4-pin C-V testing Four-pin pulse I-V test setup using the Keithley Model 4200-PIV-A NOTE The setup for 4-pin pulse I-V testing requires four prober cable kits.
- Page 12 Model 4210 MMPC-S Quick Start Guide Figure 14: Connections to the gate and source of the DUT Figure 15: Connections to the drain and bulk Figure 16: Jumper connections PA-1000 Rev. B / January 2010...
Need help?
Do you have a question about the 4210-MMPC-S and is the answer not in the manual?
Questions and answers