Plc Side Setting (Mp2000 Series, Mp920 Series) - Mitsubishi Electric GT16 User Manual


Ethernet setting
Item Description
The host is displayed. (The host is
Host
indicated with an asterisk (*).))
Set the network No. of the
N/W No. connected Ethernet module.
(Default: blank)
Set the station No. of the
*1
connected Ethernet module.
PLC No.
(Default: blank)
Type YASKAWA (fixed)
Set the IP address of the
IP address connected Ethernet module.
(Default: blank)
Set the port No. of the connected
Port No. Ethernet module.
(Default: 10500)
Communication Select a communication protocol.
format (Default: UDP)
*1 Each of [GOT PLC No.] set in the communication detail
setting and [PLC No.] set in the Ethernet setting must be set
to different station numbers.
49.3.2 ■ Communication detail settings
POINT POINT POINT
(1) Communication interface setting by the Utility
The communication interface setting can be
changed on the Utility's [Communication setting]
after writing [Communication Settings] of project
data.
For details on the Utility, refer to the following.
12. COMMUNICATION INTERFACE SETTING
(COMMUNICATION SETTING)
(2) Precedence in communication settings
When settings are made by GT Designer3 or the
Utility, the latest setting is effective.
49 - 14
49. CONNECTION TO YASKAWA PLC
49.3 Ethernet Connection
49.3.3 PLC side setting (MP2000
POINT POINT POINT

Set value
―
(1) Settings for 218IF-01
1 to 239
1 to 64
YASKAWA (fixed)
PLC side IP
address
256 to 65534
Parameter
UDP, TCP
setting
Local Port:
TCP/IP
Setting
series, MP920 series)
YASKAWA PLC
For details of YASKAWA PLCs, refer to the following
manuals.
YASKAWA PLC user's Manual
Parameter settings
Make the parameter settings with a peripheral tool.
Item
Local IP Address
Response Time
Count of Retry (Number of
Retries)
*1
CNO
(Connection Number)
Local Port (Local Station's
Port Number)
Node IP Address (Remote
*2
Station's IP Address)
Node Port (Remote
*2
Station's Port Number)
Connection Type
Protocol Type
Code
Node Name (Remote
Station's Name)
Subnet Mask
Gateway IP Address
System Port No.
(Diagnostic/Engineering
Port No.)
TCP (Transmission
Control Protocol) Zero
Window Timer Value
TCP Retry Time
TCP Close Time
IP Assemble Time
MAX. Packet Length
*1 Set the same the Node IP Address (Remote Station's IP
Address) and the Node Port (Remote Station's Port Number)
as the Local IP Address and the Local Port (Local Station's
Port Number) on the GOT side.
For the Local IP Address and the Local Port (Local Station's
Port Number) on the GOT side, refer to the following.
*2 Set the same the Node IP Address (Remote Station's IP
Address) and the Node Port (Remote Station's Port Number)
as the Local IP Address and the Local Port (Local Station's
Port Number) on the GOT side.
For the Local IP Address and the Local Port (Local Station's
Port Number) on the GOT side, refer to the following.
49.3.2 ■ Ethernet setting
Set value Range
PLC side IP
[ ].[ ].[ ].[ ]
address
Not required for
0 communication
with GOT
Not required for
0 communication
with GOT
1 1 to 20
10500 256 to 65534
IP address
[ ].[ ].[ ].[ ]
of GOT
Port No.
[ ]
of GOT
UDP
UDP/TCP
(recommended)
Extended
MEMOBUS,
Extended MEMOBUS,
MEMOBUS MELSEC,
None,
MODBUS/TCP
BIN RTU, BIN, ACII
GOT1000 Name of GOT
[ ].[ ].[ ].[ ]
[ ].[ ].[ ].[ ]
10000
PLC side
3 sec
setting
500ms
60 sec
30 sec
1500 bytes