WAGO I/O SYSTEM 750 Manual page 12

12 Table of Contents
11.1.2.2
11.1.2.3
11.1.2.4
11.1.3
11.1.3.1
11.1.3.2
11.1.3.3
11.1.3.4
11.1.3.5
11.2
11.3
11.3.1
11.3.2
11.3.3
11.3.4
11.3.5
11.3.6
11.3.7
11.3.7.1
11.3.7.2
12 Diagnostics ................................................................................................ 374
12.1
12.1.1
12.1.2
12.2
12.2.1
12.2.2
12.2.3
12.2.4
13 Service ....................................................................................................... 390
13.1
13.1.1
13.1.2
13.2
13.2.1
13.2.2
13.2.3
14 Removal .................................................................................................... 395
14.1
14.1.1
14.1.2
15 Appendix ................................................................................................... 397
15.1
15.1.1
15.1.1.1
15.1.1.2
15.1.1.3
PROFIBUS Master DP Parameters ............................................. 344
PROFIBUS Master bus parameters ............................................. 346
PROFIBUS Master Module Parameters ...................................... 348
PROFIBUS Slave PLC Configuration ............................................. 349
PROFIBUS Slave Basic Parameters ............................................ 349
PROFIBUS Slave DP Parameters ............................................... 350
PROFIBUS Slave Inputs/Outputs ................................................ 352
PROFIBUS Slave User Parameters ............................................. 354
PROFIBUS Slave Group Allocation ........................................... 356
Access to PROFIBUS Process Data ..................................................... 357
Fieldbus Coupler Diagnostics ............................................................... 359
Enable channel diagnostics ............................................................... 359
DiagGetBusState() and DiagGetState() ............................................ 361
Creating Diagnostics in CODESYS 2.3 ........................................... 362
Calling Up the Diagnostics Function Block ..................................... 364
Performing Bus Diagnostics using DiagGetBusState() .................... 364
Performing Subscriber Diagnostics using DiagGetState() ............... 368
Analyzing PROFIBUS Diagnostics of Individual I/O Modules ...... 369
Description of Diagnostic Information on the Function Block
DiagGetState.EXTENDEDINFO for PROFIBUS ...................... 370
Description of Diagnostic Information for WAGO I/O Modules 372
Operating and Status Messages ............................................................. 374
Power Supply Indicating Elements .................................................. 374
Fieldbus/System Indicating Elements .............................................. 375
Diagnostics Messages via Flashing Sequences ..................................... 381
Flashing Sequences .......................................................................... 381
Example of a Diagnostics Message Indicated by a Flashing Sequence383
Meaning of Blink Codes and Procedures for Troubleshooting ........ 384
Meaning of Blink Codes and Procedures for Troubleshooting ........ 389
Inserting and Removing the Memory Card ........................................... 390
Inserting the Memory Card .............................................................. 390
Removing the Memory Card ............................................................ 390
Firmware Changes ................................................................................ 392
Perform Firmware Upgrade .............................................................. 392
Perform Firmware Downgrade ......................................................... 393
Factory Reset .................................................................................... 394
Removing Devices ................................................................................ 395
Removing the Controller .................................................................. 395
Removing the I/O Module ................................................................ 396
Structure of Process Data for the I/O Modules ..................................... 397
Digital Input Modules....................................................................... 398
1 Channel Digital Input Module with Diagnostics ...................... 398
2 Channel Digital Input Modules ................................................ 398
2 Channel Digital Input Module with Diagnostics ...................... 398
750-8208 PFC200 CS 2ETH RS CAN DPM
Version 1.1.0, valid from FW Version 02.06.20(09)
WAGO-I/O-SYSTEM 750
Manual