Canon imageRUNNER ADVANCE C350 series Service Manual page 624

Error Detail
Location Item
code Code
E009 0001 05 Title Fixing pressure timeout error
Detection Signal of the Fixing Pressure Release Sensor could not
description be detected at pressure application operation of the Fixing
Pressure Release Cam, and the operation was not completed
within 4 sec from the start of counterclockwise rotation of the
Fixing Motor.
Remedy [Related parts]
- Fixing Assembly (Unit of replacement: Fixing Assembly)
- Harness between the Fixing Drawer (DR01/J5401) and the DC
Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK
ASSEMBLY)
- Harness between the DC Controller PCB (UN04/J135) and the
Fixing Motor (M04/J5412) (Unit of replacement: CABLE, FIXING
DRIVE)
- Harness between the Fixing Drawer (DR01/J5401) and
the Fixing Pressure Release Sensor (PS13/J5403) (Unit of
replacement: CABLE, FIXING ASSEMBLY)
- Fixing Pressure Release Sensor (PS13) (Unit of replacement:
PHOTO INTERRUPTER)
- Fixing Drive Unit (Unit of replacement: FIXING DRIVE
ASSEMBLY)
- DC Controller PCB (UN04) (Unit of replacement: DC
CONTROLLER PCB ASSEMBLY)
- Harness between the Low-voltage Power Supply PCB (UN01/
J315 and J322) and the DC Controller PCB (UN04/J20 and
J22) (Unit of replacement: CABLE, POWER SUPPLY)
- Low Voltage Power Supply PCB (UN01) (Unit of replacement:
POWER SUPPLY ASSEMBLY)
[Points to note at work] When checking the harness/cable or
connector, perform the following work.
1. Disconnect and then connect the connector to check that
there is no bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
[Reference] Before replacing the DC Controller PCB, back up
the service mode data (approx. 2 min) and restore the backup
data after the replacement so the data may be able to be
protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM>
DSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM>
DSRAMRES
7
Error•Jam•Alarm > Error Code > Error Code Details
Description
7 Error•Jam•Alarm > Error Code > Error Code Details
Error Detail
Location Item
code Code
E009 0002 05 Title Fixing disengagement timeout error
Detection Signal of the Fixing Pressure Release Sensor could not be
description detected at pressure release operation of the Fixing Pressure
Release Cam, and the operation was not completed within 4
sec from the start of counterclockwise rotation of the Fixing
Motor.
Remedy [Related parts]
- Fixing Assembly (Unit of replacement: Fixing Assembly)
- Harness between the Fixing Drawer (DR01/J5401) and the DC
Controller PCB (UN04/J134) (Unit of replacement: INTERLOCK
ASSEMBLY)
- Harness between the DC Controller PCB (UN04/J135) and the
Fixing Motor (M04/J5412) (Unit of replacement: CABLE, FIXING
DRIVE)
- Harness between the Fixing Drawer (DR01/J5401) and
the Fixing Pressure Release Sensor (PS13/J5403) (Unit of
replacement: CABLE, FIXING ASSEMBLY)
- Fixing Pressure Release Sensor (PS13) (Unit of replacement:
PHOTO INTERRUPTER)
- Fixing Drive Unit (Unit of replacement: FIXING DRIVE
ASSEMBLY)
- DC Controller PCB (UN04) (Unit of replacement: DC
CONTROLLER PCB ASSEMBLY)
- Harness between the Low-voltage Power Supply PCB (UN01/
J315 and J322) and the DC Controller PCB (UN04/J20 and
J22) (Unit of replacement: CABLE, POWER SUPPLY)
- Low Voltage Power Supply PCB (UN01) (Unit of replacement:
POWER SUPPLY ASSEMBLY)
[Points to note at work] When checking the harness/cable or
connector, perform the following work.
1. Disconnect and then connect the connector to check that
there is no bent pin and cable disconnection.
2. Visually check that the harness is not caught or open circuit.
3. If there is any error, replace the corresponding harness/cable.
[Remedy] Check/replace the related parts.
[Reference] Before replacing the DC Controller PCB, back up
the service mode data (approx. 2 min) and restore the backup
data after the replacement so the data may be able to be
protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM>
DSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM>
DSRAMRES
7-10
Description
7-10