Canon imageRUNNER ADVANCE C350 series Service Manual page 877

FUNCTION
■ INSTALL
COPIER> FUNCTION> INSTALL
STRD-POS Adj reading position:DADF stream reading
Lv.1 Details To adjust the reading position at DADF stream reading.
After the adjustment, write the value displayed by COPIER>
ADJUST> ADJ-XY> STRD-POS in the service label.
Use case At DADF installation/uninstallation
Adj/set/operate method 1) Close the DADF.
2) Select the item, and then press OK key.
It stops automatically.
Caution Write the adjusted value in the service label.
Display/adj/set range At normal termination: OK, At abnormal termination: NG
Related service mode COPIER> ADJUST> ADJ-XY> STRD-POS
CARD Card number setting
Lv.1 Details To set the card number to be used for Card Reader.
A series of numbers from the entered number to the number of cards
specified by CARD-RNG can be used.
Use case - At installation of the Card Reader
- After replacement of the HDD
Adj/set/operate method 1) Enter the number, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution The card management information (department ID and password) is
initialized.
Display/adj/set range 0 to 2001
Default value 0
Related service mode COPIER> OPTION> FNC-SW> CARD-RNG
AINR-OFF ON/OFF warm-up rotn deact:dor open/close
Lv.1 Details To set whether to disable the warm-up rotation when opening and
closing the door.
By selecting 1, printing can be executed without auto adjustment at
warm-up rotation when analyzing the cause of a problem.
Use case When printing and checking without auto adjustment at warm-up
rotation when analyzing the cause of a problem
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF (warm-up rotation enabled), 1: ON (warm-up rotation
disabled)
Default value 0
8
Service Mode > COPIER > FUNCTION > INSTALL
8 Service Mode > COPIER > FUNCTION > INSTALL
COPIER> FUNCTION> INSTALL
E-RDS Set use/no use of Embedded-RDS function
Lv.1 Details To set whether to use the Embedded-RDS function.
Use case When using Embedded-RDS
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to use E-RDS, RGW-PORT, COM-TEST, COM-LOG and
RGW-ADR as a set.
Display/adj/set range 0 to 1
0: Not used, 1: Used (All the counter information is sent.)
Default value 0
Related service mode COPIER> FUNCTION> INSTALL> RGW-PORT, COM-TEST, COM-
LOG, RGW-ADR
COPIER> FUNCTION> CLEAR> ERDS-DAT
Supplement/memo Embedded-RDS: Function to send device information such as the
device counter, failure, and consumables to the sales company's
server via SOAP protocol
RGW-PORT Set port number of Sales Co's server
Lv.1 Details To set the port number of the sales company's server to be used for
Embedded-RDS.
Use case When using Embedded-RDS
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to use E-RDS, RGW-PORT, COM-TEST, COM-LOG and
RGW-ADR as a set.
Display/adj/set range 1 to 65535
Default value 443
Related service mode COPIER> FUNCTION> INSTALL> E-RDS, COM-TEST, COM-LOG,
RGW-ADR
COPIER> FUNCTION> CLEAR>ERDS-DAT
Supplement/memo Embedded-RDS: Function to send device information such as the
device counter, failure, and consumables to the sales company's
server via SOAP protocol
COM-TEST Dspl connect result w/ Sales Co's server
Lv.1 Details To display the result of the connection test with the sales company's
server.
Use case When using Embedded-RDS
Adj/set/operate method Select the item, and then press OK key.
Caution Be sure to use E-RDS, RGW-PORT, COM-TEST, COM-LOG and
RGW-ADR as a set.
Display/adj/set range During operation: ACTIVE, When connection is completed: OK,
When connection is failed: NG
Related service mode COPIER> FUNCTION> INSTALL> E-RDS, RGW-PORT, COM-LOG,
RGW-ADR
Supplement/memo Embedded-RDS: Function to send device information such as the
device counter, failure, and consumables to the sales company's
server via SOAP protocol
8-107
8-107