Canon imageRUNNER ADVANCE C350 series Service Manual page 875

COPIER> ADJUST> CST-ADJ
CST-VLM4 Adj Cassette 4 level detect threshold VL
Lv.2 Details To adjust the timing to switch the scale indicating paper level in the
Cassette 4 from "3" to "2".
As the value is larger, switching of the level display becomes earlier.
For example, if you prefer to switch the scale when paper level
reaches 25 mm instead of 15 mm, place a stack of papers which
height is approx. 25 mm in the cassette and then increase the setting
value by 1 at a time until the scale becomes "2".
If the scale is switched although paper level is 40 mm, place a stack
of papers which height is approx. 35 mm in the cassette and then
decrease the setting value by 1 at a time until the scale becomes "3".
If the value that satisfy both of the above conditions is set, the scale
is switched when paper level is in the range of 25 to 35 mm.
Use case Upon user's request (to individually adjust the timing to switch the
paper level display)
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Pull out and then insert the cassette.
Caution - The setting is reflected after removing and then installing the
cassette.
- When the value is increased/decreased greatly, the actual timing
may be deviated from the target. Therefore, change the value by 1 at
a time while checking the scale.
Display/adj/set range -4 to 4
Appropriate target value 0
Default value 0
Supplement/memo The timing to switch the scale of paper level from "3" to "2" varies (9
to 40 mm) due to individual difference of the motor. With this item,
the variation is corrected.
Since paper levels corresponding to the other scales can be detected
almost correctly, there is no need to adjust the timing of switching.
8
Service Mode > COPIER > ADJUST > MISC
T-8-26
8 Service Mode > COPIER > ADJUST > MISC
■ MISC
COPIER> ADJUST> MISC
SEG-ADJ Set criteria for text/photo: front side
Lv.1 Details To set the judgment level of text/photo original in Text/Photo/Map
mode.
As the value is increased, the original tends to be detected as a
photo document, and as the value is decreased, the original tends to
be detected as a text document.
Use case When adjusting the classification level of text and photo in Text/
Photo/Map mode
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not use this at the normal service. Take necessary action in
accordance with the instructions from the QA Center.
Display/adj/set range -4 to 4
Default value 0
K-ADJ Set criteria for black text: front side
Lv.1 Details To set the judgment level of black characters at text processing.
As the value is increased, the text tends to be detected as black.
Use case When preferring the text to be judged as black
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -3 to 3
Default value 0
ACS-ADJ Set criteria for B&W/color in ACS:front
Lv.1 Details To set the judgment level of B&W/color original in ACS mode.
As the value is increased, the original tends to be detected as a
B&W document, and as the value is decreased, the original tends to
be detected as a color document.
Use case When adjusting the color detection level in ACS mode
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -3 to 3
Default value 0
ACS-EN Set judgment area in ACS mode:front
Lv.2 Details To set the judgment area in ACS mode.
As the greater value is set, the judgment area is widened.
Use case When adjusting the judgment area in ACS mode
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -2 to 2
Default value 1
8-105
8-105