Canon imageRUNNER ADVANCE C350 series Service Manual page 870

COPIER> ADJUST> FEED-ADJ
ADJ-C4RE Write start pstn in horz scan:Cst4 2nd
Lv.1 Details To adjust the image write start position in the horizontal scanning
direction for 2nd side when feeding paper from the Cassette 4.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Left margin becomes larger (An image moves to the right.)
-: Left margin becomes smaller (An image moves to the left.)
When replacing the Reader Controller PCB/clearing RAM data, enter
the value of service label.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
ADJ-MFRE Write start pstn in horz scan:MPTray 2nd
Lv.1 Details To adjust the image write start position in the horizontal scanning
direction for 2nd side when feeding paper from the Multi-purpose
Tray.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Left margin becomes larger. (An image moves to the right.)
-: Left margin becomes smaller. (An image moves to the left.)
When replacing the Reader Controller PCB/clearing RAM data, enter
the value of service label.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
REG-THCK Register start timing adj: 1/2 speed
Lv.1 Details To adjust the top margin by changing the timing to turn ON the
Registration Motor at 1/2 speed.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Top margin becomes larger. (An image moves downward.)
-: Top margin becomes smaller. (An image moves upward.)
Use case When adjusting the leading edge margin
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
8
Service Mode > COPIER > ADJUST > FEED-ADJ
8 Service Mode > COPIER > ADJUST > FEED-ADJ
COPIER> ADJUST> FEED-ADJ
REG-DUP1 Rgst start timing adj: Plain, 2nd side
Lv.1 Details To adjust the top margin by changing the timing to turn ON the
Registration Motor when feeding the second side of plain paper.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Top margin becomes larger. (An image moves downward.)
-: Top margin becomes smaller. (An image moves upward.)
Use case When adjusting the leading edge margin
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
LP-FEED1 Adj of per-rest arch amount: 1/1 speed
Lv.1 Details To adjust the arch amount before registration at 1/1 speed.
The setting is applied in case of pickup from a cassette/Multi-purpose
Tray and 1-sided/2-sided printing.
As the value is incremented by 1, the arch amount changes by 0.1
mm.
+: Increase
-: Decrease
Use case When adjusting the arch amount before registration at 1/1 speed
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -20 to 20
Unit 0.1 mm
Default value 0
LP-FEED2 Adj of pre-rgst arch amount: 1/2 speed
Lv.1 Details To adjust the arch amount before registration at 1/2 speed.
The setting is applied in case of pickup from a cassette/Multi-purpose
Tray and 1-sided/2-sided printing.
As the value is incremented by 1, the arch amount changes by 0.1
mm.
+: Increase
-: Decrease
Use case When adjusting the arch amount before registration at 1/2 speed
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -20 to 20
Unit 0.1 mm
Default value 0
8-100
8-100