Canon imageRUNNER ADVANCE C350 series Service Manual page 832

COPIER> ADJUST> CCD
MTF-S4 MTF value 4 setting: vert scan [DADF]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case - When replacing the Scanner Unit
- When replacing the Main Controller PCB/clearing the Reader-
related RAM data
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range 0 to 100
Unit 1 %
Default value 100
MTF-S5 MTF value 5 setting: vert scan [DADF]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case - When replacing the Scanner Unit
- When replacing the Main Controller PCB/clearing the Reader-
related RAM data
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range 0 to 100
Unit 1 %
Default value 100
MTF-S6 MTF value 6 setting: vert scan [DADF]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case - When replacing the Scanner Unit
- When replacing the Main Controller PCB/clearing the Reader-
related RAM data
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range 0 to 100
Unit 1 %
Default value 100
8
Service Mode > COPIER > ADJUST > CCD
8 Service Mode > COPIER > ADJUST > CCD
COPIER> ADJUST> CCD
MTF-S7 MTF value 7 setting: vert scan [DADF]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case - When replacing the Scanner Unit
- When replacing the Main Controller PCB/clearing the Reader-
related RAM data
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range 0 to 100
Unit 1 %
Default value 100
MTF-S8 MTF value 8 setting: vert scan [DADF]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case - When replacing the Scanner Unit
- When replacing the Main Controller PCB/clearing the Reader-
related RAM data
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range 0 to 100
Unit 1 %
Default value 100
MTF-S9 MTF value 9 setting: vert scan [DADF]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case - When replacing the Scanner Unit
- When replacing the Main Controller PCB/clearing the Reader-
related RAM data
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range 0 to 100
Unit 1 %
Default value 100
8-62
8-62