Canon imageRUNNER ADVANCE C350 series Service Manual page 823

COPIER> ADJUST> ADJ-XY
STRD-POS Adj read pstn in DADF mode: front side
Lv.1 Details To adjust the reading position at DADF reading (front side).
When replacing the Scanner Unit or Main Controller PCB/clearing
the Reader-related RAM data, enter the value of service label.
Use case - When replacing the Scanner Unit
- When replacing the Main Controller PCB/clearing the Reader-
related RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -30 to 20
Unit 0.1 mm
Default value 0
Related service mode COPIER> FUNCTION> INSTALL> STRD-POS
ADJ-X-MG Fine adj img ratio: book mode, vert scan
Lv.1 Details To make a fine adjustment of image magnification ratio in vertical
scanning direction at copyboard reading.
When replacing the Scanner Unit or Main Controller PCB/clearing
the Reader-related RAM data, enter the value of service label.
As the value is incremented by 1, the image magnification ratio
changes by 0.01 %.
+: Enlarge
-: Reduce
Use case - When replacing the Scanner Unit
- When replacing the Main Controller PCB/clearing the Reader-
related RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -200 to 200
Unit 0.01 %
Default value 0
8
Service Mode > COPIER > ADJUST > CCD
T-8-16
8 Service Mode > COPIER > ADJUST > CCD
■ CCD
COPIER> ADJUST> CCD
W-PLT-X White level data(X) entry of White Plate
Lv.1 Details When replacing the Reader Controller PCB/clearing the Reader-
related RAM data, enter the value of P-PRINT. When replacing the
Copyboard Glass, enter the value of barcode label which is affixed
on the glass.
Use case - When replacing the Main Controller PCB
- When clearing the Reader-related RAM data
- When replacing the Copyboard Glass
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution Output the service mode setting values by P-PRINT beforehand.
Display/adj/set range 7000 to 9999
Default value 8273
Related service mode COPIER> ADJUST> CCD> W-PLT-Y/Z
COPIER> FUNCTION> MISC-P> P-PRINT
W-PLT-Y White level data(Y) entry of White Plate
Lv.1 Details When replacing the Reader Controller PCB/clearing the Reader-
related RAM data, enter the value of P-PRINT. When replacing the
Copyboard Glass, enter the value of barcode label which is affixed
on the glass.
Use case - When replacing the Main Controller PCB
- When clearing the Reader-related RAM data
- When replacing the Copyboard Glass
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution Output the service mode setting values by P-PRINT beforehand.
Display/adj/set range 7000 to 9999
Default value 8737
Related service mode COPIER> ADJUST> CCD> W-PLT-X/Z
COPIER> FUNCTION> MISC-P> P-PRINT
W-PLT-Z White level data(Z) entry of White Plate
Lv.1 Details When replacing the Reader Controller PCB/clearing the Reader-
related RAM data, enter the value of P-PRINT. When replacing the
Copyboard Glass, enter the value of barcode label which is affixed
on the glass.
Use case - When replacing the Main Controller PCB
- When clearing the Reader-related RAM data
- When replacing the Copyboard Glass
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution Output the service mode setting values by P-PRINT beforehand.
Display/adj/set range 7000 to 9999
Default value 9427
Related service mode COPIER> ADJUST> CCD> W-PLT-X/Y
COPIER> FUNCTION> MISC-P> P-PRINT
8-53
8-53