Canon imageRUNNER ADVANCE C350 series Service Manual page 157

2
Technical Explanation > Pickup / Feed System > Controls > Jam Detection
The Duplex Solenoid (SL02) is turned ON 100 msec before the leading edge of the fed paper
reaches the duplex standby position. After the Duplex Solenoid (SL02) is turned ON, the drive
of the Duplex Feed Lower Roller is terminated, and the paper stops at the duplex standby
position. After the designated time has elapsed, the Duplex Solenoid is turned OFF, the
Duplex Feed Lower Roller is driven, and then the paper is picked up again.
Delivery Sensor (PS12)
22.3 mm
● Duplex Circulation
The following shows the number of circulating sheets at the 2-sided print.
Length in paper feed direction
297.0 mm or less
Greater than 297.0 mm
2 Technical Explanation > Pickup / Feed System > Controls > Jam Detection
Duplex Feed
Lower Roller
M08
SL02
M06
Duplex Feed
Upper Roller
Duplex Sensor
(PS01)
Duplex standby position
F-2-148
Number of circulating sheets
3
1
T-2-54
■ Jam Detection
● List of Jam Codes
A jam code consists of 4 alphanumeric characters.
The upper 2 digits indicate the jam type, and the lower 2 digits indicate the sensor that
detected a jam.
ACC ID Jam Code Type
00 0101 Delay Cassette 1 Pickup Sensor
00 0102 Delay Cassette 2 Pullout Sensor
00 0103 Delay Cassette 3 Pullout Sensor
00 0104 Delay Cassette 4 Pullout Sensor
00 0105 Delay Pre-Registration Sensor
00 0106 Delay Delivery Sensor
00 0107 Delay Duplex Sensor
00 0202 Stationary Cassette 2 Pullout Sensor
00 0203 Stationary Cassette 3 Pullout Sensor
00 0204 Stationary Cassette 4 Pullout Sensor
00 0205 Stationary Pre-Registration Sensor
00 0206 Stationary Delivery Sensor
00 0706 Fixing paper Fixing paper wrapping jam
wrapping
00 0709 Fixing paper Fixing paper wrapping jam
wrapping
00 0A01 Power ON Cassette 1 Pickup Sensor
00 0A02 Power ON Cassette 2 Pullout Sensor
00 0A03 Power ON Cassette 3 Pullout Sensor
00 0A04 Power ON Cassette 4 Pullout Sensor
00 0A06 Power ON Delivery Sensor
00 0A07 Power ON Duplex Sensor
00 0A08 Power ON Arch Sensor
00 0A90 Power ON Pre-Registration Sensor
00 0A91 Power ON Multi-purpose Tray HP Sensor
00 0A92 Power ON Multi-purpose Tray HP Sensor
00 0B00 Door Open -
00 0B0D No drum jam* -
00 0CA1 Sequence Software sequence
(Feed status cannot be returned)
00 0CA2 Sequence Software sequence
(ImageReady cannot be sent)
00 0CA3 Sequence Software sequence
(Stop due to jam is not possible)
00 0CA4 Sequence Software sequence (Finisher-related)
00 0CA9 Sequence Software sequence error
(Automatic adjustment-related)
00 0CAF Sequence Finisher sequence jam
2-114
Sensor Name Sensor ID
PS5
PS101
PS102
PS103
PS4
PS12
PS1
PS101
PS102
PS103
PS4
PS12
-
-
PS5
PS101
PS102
PS103
PS12
PS1
PS11
PS4
PS10
PS10
-
-
-
-
-
-
-
-
2-114