Canon imageRUNNER ADVANCE C350 series Service Manual page 928

COPIER> OPTION> NETWORK
SPDALDEL Initialization of SPD value
Lv.2 Details To initialize all the SPD values that are under management.
SPD values can be initialized without clearing SRAM.
Use case At the time of SPD value mismatch when IPSec Board is added
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Supplement/memo SPD: Database that manages SA (Security Association).
SPD value is managed when IPSec Board is used. Normally, SRAM
needs to be cleared in the case of mismatch in SPD value.
NCONF-SW ON/OFF of Network Configurator function
Lv.1 Details To set ON/OFF of Network Configurator function.
If the user does not use the function, select OFF to prevent remote
attack through network.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Supplement/memo Network Configurator function is a function to be used for
communication with NetSpot Device Installer, etc., and the network
setting can be changed from the remote.
IKEINTVL Setting of IKE retry interval
Lv.1 Details To set retry interval in the case of no response from the
communication target at the time of IKE packet transmission.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 10
Unit 1 second
Default value 5
Supplement/memo IKE: Internet Key Exchange
IPSDEBLV For R&D
8
Service Mode > COPIER > OPTION > NETWORK
8 Service Mode > COPIER > OPTION > NETWORK
COPIER> OPTION> NETWORK
SP-LINK Mode setting at 1W sleep
Lv.1 Details To set the condition to shit to sleep mode
When 0 is set, 10base-T standby is executed, therefore standby
power 1W can be realized.
When 1 is set, the machine enters sleep mode after negotiation (same
as conventional machines).
Use case When shifting to sleep mode after negotiation (same as conventional
machines)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: 10base-T standby, 1: Shift to sleep mode after negotiation
Default value 0
AFS-JOB Set of FAX server job reception port
Lv.1 Details To set the reception port of the fax server to which a fax client sends
jobs.
Use case When changing the job reception port of the fax server
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 65535
Default value 20317
Related service mode COPIER> OPTION> NETWORK> AFC-EVNT
AFC-EVNT Set of FAX client event reception port
Lv.1 Details To set the event notification reception port of a fax client.
Use case When changing the event notification reception port of a fax client
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 65535
Default value 29400
Related service mode COPIER> OPTION> NETWORK> AFS-JOB
ILOGMODE Setting of IP address block mode
Lv.1 Details To set all protocols or TCP/UDP/ICMP unicast as the target of IP
block.
When 0 is set, the machine responds to ARP, ICMP multicast and
broadcast which have no direct relation, and consequently the
number of logs is increased.
When 1 is set, the machine filters TCP, UDP and ICMP unicast only.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 3
0: All protocols support mode, 1: TCP/UDP/ICMP unicast support
mode, 2, 3: Not used
Default value 0
8-158
8-158