Canon imageRUNNER ADVANCE C350 series Service Manual page 687

Error Detail
Location Item
code Code
E350 0003 00 Title System error
Detection System error
description
Remedy Contact to the sales company.
E350 3000 00 Title System error
Detection System error
description
Remedy Contact to the sales company.
E351 0000 00 Title Main Controller PCB communication error
Detection Communication function of the Main Controller PCB did not
description work properly.
Remedy [Remedy] Replace the Main Controller PCB (UN81). (Unit of
replacement: MAIN CONTROLLER PCB ASSEMBLY)
E354 0001 00 Title System error
Detection System error
description
Remedy Contact to the sales company.
E354 0002 00 Title System error
Detection System error
description
Remedy Contact to the sales company.
E355 0001 00 Title System error
Detection System error
description
Remedy Contact to the sales company.
E355 0002 00 Title System error
Detection System error
description
Remedy Contact to the sales company.
E355 0003 00 Title System error
Detection System error
description
Remedy Contact to the sales company.
E355 0004 00 Title System error
Detection System error
description
Remedy Contact to the sales company.
E500 0000 02 Title Finisher communication error
Detection An error was detected on the finisher side.
description
Remedy 1. Check that the connector (CN1/P3/J3) of the Interface
Harness is not disconnected.
2. Replace the Finisher Controller PCB.
3. Replace the Interface Harness.
7
Error•Jam•Alarm > Error Code > Error Code Details
Description
7 Error•Jam•Alarm > Error Code > Error Code Details
Error Detail
Location Item
code Code
E530 0001 02 Title Front Alignment Plate HP Sensor error
Detection The Front Alignment Motor did not move from the HP.
description
Remedy 1. Check that the connector (P8-3/P8/J8) of the Front Alignment
Plate HP Sensor (S4) is not disconnected.
2. Check that the connector (P6-12/P6-2/J6-2/P6/J6) of the
Front Alignment Motor (M4) is not disconnected.
3. Replace the Front Alignment Plate HP Sensor (S4).
4. Replace the Front Alignment Motor (M4).
5. Check the conditions of the front alignment drive parts (belt
and gear).
6. Replace the Finisher Controller PCB.
7. Replace the Harness Assembly.
E530 0002 02 Title Front Alignment Motor error
Detection The Front Alignment Motor did not return to the HP.
description
Remedy 1. Check that the connector (P8-3/P8/J8) of the Front Alignment
Plate HP Sensor (S4) is not disconnected.
2. Check that the connector (P6-12/P6-2/J6-2/P6/J6) of the
Front Alignment Motor (M4) is not disconnected.
3. Replace the Front Alignment Plate HP Sensor (S4).
4. Replace the Front Alignment Motor (M4).
5. Check the conditions of the front alignment drive parts (belt
and gear).
6. Replace the Finisher Controller PCB.
7. Replace the Harness Assembly.
E531 8001 02 Title Staple Motor error
Detection The Staple Motor did not move from the HP.
description
Remedy 1. Check that the connector (P9-1/P9/J9) of the Staple HP
Sensor (S11) is not disconnected.
2. Check that the connector (P10-1/P10/J10) of the Staple
Motor (M9) is not disconnected.
3. Replace the Stapler.
4. Replace the Finisher Controller PCB.
5. Replace the Harness Assembly.
E531 8002 02 Title Staple Motor error
Detection The Staple Motor did not return to the HP.
description
Remedy 1. Check that the connector (P9-1/P9/J9) of the Staple HP
Sensor (S11) is not disconnected.
2. Check that the connector (P10-1/P10/J10) of the Staple
Motor (M9) is not disconnected.
3. Replace the Stapler.
4. Replace the Finisher Controller PCB.
5. Replace the Harness Assembly.
7-73
Description
7-73