Canon imageRUNNER ADVANCE C350 series Service Manual page 879

COPIER> FUNCTION> INSTALL
HD-CRYP Exe HDD Encrypt Board ini install mod
Lv.1 Details To automatically execute operation necessary for initial installation of
the HDD Encryption Board.
By turning OFF the main power switch after execution, the HDD
Encryption Board can be installed.
Use case At installation of the HDD Encryption Board
Adj/set/operate method Select the item, and then press OK key.
Caution Be sure to install the HDD Encryption Board after executing the
service mode and turning OFF the main power switch. If you make
a mistake in the procedure, remove the HDD Encryption Board and
redo the procedure.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
RDSHDPOS Auto adj of Reader shading position
Lv.1 Details To adjust the shading position automatically based on the result of
reading of the Standard White Plate.
Use case - When replacing the Reading Sensor Unit
- When replacing the Copyboard Glass
- When clearing the Reader-related RAM data
Adj/set/operate method Select the item, and then press OK key.
Caution When this item is executed, the value set by COPIER> ADJUST>
ADJ-XY> ADJ-S may change. After the execution, write the value of
ADJ-S in the service label.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Required time 10 sec
Related service mode COPIER> ADJUST> ADJ-XY> ADJ-S
Supplement/memo The shading position can be adjusted manually by COPIER>
ADJUST> ADJ-XY> ADJ-S.
BIT-SVC OFF/ON of Web service of eRDS
Lv.1 Details To switch ON/OFF of the Web Service function of eRDS.
When OFF is selected, authentication information cannot be
obtained from eRDS.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
8
Service Mode > COPIER > FUNCTION > CCD
T-8-28
8 Service Mode > COPIER > FUNCTION > CCD
■ CCD
COPIER> FUNCTION> CCD
DF-WLVL1 White level adj in book mode: color
Lv.1 Details To adjust the white level for copyboard scanning automatically by
setting the paper which is usually used by the user on the Copyboard
Glass.
Use case - When replacing the Copyboard Glass
- When replacing the Scanner Unit
- When clearing the Reader-related RAM data
Adj/set/operate method 1) Set paper on the Copyboard Glass.
2) Select the item, and then press OK key.
Caution Be sure to execute DF-WLVL2 in a row.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Related service mode COPIER> FUNCTION> CCD> DF-WLVL2
DF-WLVL2 White level adj in DADF mode: color
Lv.1 Details To adjust the white level for DADF scanning automatically by setting
the paper which is usually used by the user on the DADF.
Use case - When replacing the Copyboard Glass
- When replacing the Scanner Unit
- When clearing the Reader-related RAM data
Adj/set/operate method 1) Set paper on the DADF.
2) Select the item, and then press OK key.
Caution Be sure to execute this item after DF-WLVL1.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Related service mode COPIER> FUNCTION> CCD> DF-WLVL1
COPIER> ADJUST> CCD> DFTAR-R/G/B
COPIER> ADJUST> CCD> DFTAR2-R/G/B
COPIER> ADJUST> CCD> DFTAR3-R/G/B
CL-AGC Adj Scan Unit white/black ref level: AGC
Lv.1 Details To adjust the black/white reference level of the Scanner Unit
automatically (automatic gain control).
To make the adjustment with both resolutions 300 dpi and 600 dpi.
Use case - When replacing the Copyboard Glass
- When replacing the Scanner Unit
Adj/set/operate method 1) Select the item, and then press OK key.
2) After "OK!" is displayed, turn OFF/ON the main power switch.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Related service mode COPIER> ADJUST> CCD> OFST-CL0 - OFST-CL5, OFST2CL0
- OFST2CL5, GAIN-CL0, GAIN2CL0, LED-CL-R/G/B, LED2CL-R/
G/B, LED-CLR2, LED-CLG2, LED-CLB2, LED2CLR2, LED2CLG2,
LED2CLB2
8-109
T-8-29
8-109