Canon imagePRESS 1135 Series Service Manual page 1182

■ DSPLY-SW
COPIER > OPTION > DSPLY-SW
UI-COPY Disp/hide of copy screen
Lv.2 Details Setting to display/hide the copy screen button in the upper area of
the user screen.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Hide (display), 1: Display
Default value 1
UI-BOX Disp/hide of box screen
Lv.2 Details Setting to display/hide the box screen button in the upper area of the
user screen.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 2
0: No BOX function (storing is not available even with PDL to Box)
1: BOX function is active
2: BOX function is active (with limitation; storing is available with PDL
to BOX despite no display on the control panel/remote UI)
Default value 1
UI-SEND Disp/hide of send screen
Lv.2 Details Setting to display/hide the SEND screen button in the upper area of
the user screen.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Hide (display), 1: Display
Default value 1
UI-FAX Disp/hide of FAX screen
Lv.2 Details Setting to display/hide the FAX screen button in the upper area of
the user screen.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Hide (display), 1: Display
Default value 1
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > DSPLY-SW
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > DSPLY-SW
COPIER > OPTION > DSPLY-SW
T-LW-LVL [Not used]
MEAP-DSP Screen switch set from MEAP to standard
Lv.2 Details Setting to enable/disable switch from MEAP screen to the standard
screen (COPY/SEND/BOX screen, etc). (Setting to display/hide the
arrow mark on MEAP screen)
In the case of an error/jam/alarm, the screen is switched to the
standard screen to display warning even if disabling this mode.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Enable, 1: Disable
Default value 0
Related service mode COPIER> OPTION> DSPLY-SW> ANIM-SW
Supplement/memo If disabling the switch with ANIM-SW, the screen will not be switched
to the standard screen even in the case of an error/jam/alarm.
ANIM-SW Screen switch set from MEAP to warning
Lv.2 Details Setting to enable/disable switch from MEAP screen to the error/jam
screen.
If disabling this mode, the screen will not be switched to the warning
screen in the case of an error/jam/alarm, and a message is appeared
on the MEAP screen indicating to contact the service person.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Enable, 1: Disable (no display of warning screen)
Default value 0
Related service mode COPIER> OPTION> DSPLY-SW> MEAP-DSP
Supplement/memo If just disabling the switch with MEAP-DSP, the screen is switched to
the standard screen in the case of an error/jam/alarm. If disabling the
switch with ANIM-SW, the screen will not be switched to the standard
screen and a warning is appeared on MEAP screen.
UI-PRINT Disp/hide of print job screen
Lv.2 Details Setting to display/hide the print job screen.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Hide (display), 1: Display
Default value 1
8-239
8-239