Canon imagePRESS 1135 Series Service Manual page 1130

COPIER> ADJUST> HV-TR
2TR-SHR2 Adj sec trns paper allotted voltge: set2
Lv.2 Details To adjust the paper allotted voltage of secondary transfer in setting 2.
Setting 2 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV2, TR-PPR2,
TR-DUP2. When this condition is true, paper allotted voltage that is
set here is applied to the secondary transfer inner roller.
As the value is increased by 1, voltage is increased by 100 V.
Use case When an image failure that is subject to paper type occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time.
Display/adj/set range -10 to 10
Unit 100 V
Related service mode COPIER> ADJUST> HV-TR> TR-ENV2, TR-PPR2, TR-DUP2
2TR-SHR3 Adj sec trns paper allotted voltge: set3
Lv.2 Details To adjust the paper allotted voltage of secondary transfer in setting 3.
Setting 3 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV3, TR-PPR3,
TR-DUP3. When this condition is true, paper allotted voltage that is
set here is applied to the secondary transfer inner roller.
As the value is increased by 1, voltage is increased by 100 V.
Use case When an image failure that is subject to paper type occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time.
Display/adj/set range -10 to 10
Unit 100 V
Related service mode COPIER> ADJUST> HV-TR> TR-ENV3, TR-PPR3, TR-DUP3
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > HV-TR
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > HV-TR
COPIER> ADJUST> HV-TR
2TR-SHR4 Adj sec trns paper allotted voltge: set4
Lv.2 Details To adjust the paper allotted voltage of secondary transfer in setting 4.
Setting 4 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV4, TR-PPR4,
TR-DUP4. When this condition is true, paper allotted voltage that is
set here is applied to the secondary transfer inner roller.
As the value is increased by 1, voltage is increased by 100 V.
Use case When an image failure that is subject to paper type occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time.
Display/adj/set range -10 to 10
Unit 100 V
Related service mode COPIER> ADJUST> HV-TR> TR-ENV4, TR-PPR4, TR-DUP4
2TR-SHR5 Adj sec trns paper allotted voltge: set5
Lv.2 Details To adjust the paper allotted voltage of secondary transfer in setting 5.
Setting 5 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV5, TR-PPR5,
TR-DUP5. When this condition is true, paper allotted voltage that is
set here is applied to the secondary transfer inner roller.
As the value is increased by 1, voltage is increased by 100 V.
Use case When an image failure that is subject to paper type occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time.
Display/adj/set range -10 to 10
Unit 100 V
Default value 0
Related service mode COPIER> ADJUST> HV-TR> TR-ENV5, TR-PPR5, TR-DUP5
8-187
8-187