Canon imagePRESS 1135 Series Service Manual page 1109

COPIER> ADJUST> CCD
MTF2-S7 MTF value setting 7: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S8 MTF value setting 8: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S9 MTF value setting 9: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
100DF2GB GB color drift crrctVL in img snsr[back]
Lv.2 Details To correct the color drift between G-B lines in sub scanning direction
due to the back side scanner unit.
When the reader controller PCB is replaced or RAM is cleared, enter
the value of service label.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -256 to 256
Default value 0
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
COPIER> ADJUST> CCD
100DF2RG RG color drift crrctVL in img snsr[back]
Lv.2 Details To correct the color drift between R-G lines in sub scanning direction
due to the back side scanner unit.
When the reader controller PCB is replaced or RAM is cleared, enter
the value of service label.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -256 to 256
Default value 0
DFCH2R2 Complex chart No.2 data (R) [Front]
Lv.1 Details To calculate the front/back linearity, set the front Red data of No.2
image in DADF complex chart.
Enter the value of reader's service label.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 2550
Default value 2000
DFCH2R10 Complex chart No.10 data (R) [Front]
Lv.1 Details To calculate the front/back linearity, set the front Red data of No.10
image in DADF complex chart.
Enter the value of reader's service label.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2550
Default value 0
DFCH2B2 Complex chart No.2 data (B) [Front]
Lv.1 Details To calculate the front/back linearity, set the front Blue data of No.2
image in DADF complex chart.
Enter the value of reader's service label.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 2550
Default value 2000
DFCH2B10 Complex chart No.10 data (B) [Front]
Lv.1 Details To calculate the front/back linearity, set the front Blue data of No.10
image in DADF complex chart.
Enter the value of reader's service label.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2550
Default value 0
8-166
8-166